48” WORKBENCH 72” WORKBENCH 96” WORKBENCH Workbench Series Warning: Excessive weight hazard! Use two or more people to move, assemble or install workbench. Failure to do so can result in back or other injury. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
Parts List LONG CROSS BEAM WORKTOP LONG SUPPORT BEAM FOR 96” BENCH TOOL TRAY SHORT SUPPORT BEAM TOOL TRAY DIVIDERS LEG (A) SHORT CROSS BEAM LEG (B) 5/16” X 5/8” HEX BOLTS 5/16” LOCK WASHERS #8-32 X 7/8” BOLTS #8-32 LOCK WASHERS AND NUTS ADJUSTABLE FEET #8-32 X 3/4” SCREWS #8-32 X 1” SCREWS
Tools Needed 1 x 9/16” wrench 1 x 12” Magnetic Leveler 1 x #2 Phillips Bit Screwdriver 1 x Pliers 1 x Tape Measure 1 x Pencil Parts and Hardware Supplied Parts 48” Workbench 72” Workbench 96” Workbench Threaded Adjustable Foot 4 4 4 Long Cross Beam 2 2 2 Long Support Beam 0 0 1 Short Cross Beam 2 2 2 Short Support Beam 2 2 2 Leg (A) 2 2 2 Leg (B) 2 2 2 5/16” x 5/8”L Hex Bolts 32 32 36 5/16” Lock Washers 32 32 36 #8 x 3/4” Wood Screws 12 12 12 #8-32 x 7/8” Bo
Assemble The Frame 1. Select one Leg (A) and one Leg (B) and lay them opposite one another on the floor with the leg brackets positioned on the outside of the two legs, and facing in the same direction. See Figure 1. 2. Select one Short Cross Beam, and one Short Support Beam, and bolt the side frame assembly together with the supplied 5/16” hex bolts and lock washers. See Figure 1. Note: Legs are shown being assembled upside down, as this will be easiest for assembly and installing the top. 5.
Mounting The Tool Tray 1. For Stainless Steel Top: Install four #8 x 1” screws in the locator holes along the edge of the worktop, 3/4 of the way in. Installing Bamboo Top Tray 1 Fig.1 WORKTOP For Bamboo Top: Place tray flush with the top of worktop (Figure 1) and use the tray as a guide to mark the center of the top of the keyholes for the 4 screw locations along the edge. (Figure 2) + MARK CENTER HERE KEYHOLE ON TRAY 2. Slide the keyholes on the side of the tray over the heads of the screws.
Mounting Power Bar 1. Insert the two #8-32 bolts into the slots on the back of the power bar. Secure the screws in the lower gap towards the cord. 2.Install the power bar onto the workbench by inserting the two screws through the corresponding holes on the front, or sides of the workbench. 1 2 If installing the power bar on the front of the workbench you can feed the cord for the power bar through the rubber grommets on the front and back of the workbench. 3.
NEWAGE PRODUCTS INC. WELDED WORKBENCH 10 YEAR LIMITED MANUFACTURER WARRANTY When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of ten years from the date of purchase. NEWAGE PRODUCTS INC. WILL NOT PAY FOR: 1.
ÉTABLI DE 48 PO (121,92 CM) ÉTABLI DE 72 PO (182,88 CM) ÉTABLI DE 96 PO (243,84 CM) Séries Établis Avertissement : Cet article est très lourd et peut représenter un danger! Veuillez à transporter, assembler et installer cet établi avec deux personnes ou plus. Dans le cas contraire, vous pourriez vous blesser au dos ou ailleurs. Pour obtenir de l'aide, composez le 1-887-306-8930; pour le UK, le 0800-031-4069; envoyez un courriel à info@newageproducts.
Liste des pièces LONGUE POUTRE TRANSVERSALE PLAN DE TRAVAIL LONGUE POUTRE DE SOUTIEN POUR ÉTABLI DE 96 PO PLATEAU À OUTILS PETITE POUTRE DE SOUTIEN PETITE POUTRE TRANSVERSALE SÉPARATEURS POUR PLATEAU À OUTILS BARRE (A) BOULONS HEXAGONAUX DE 5/16 PO X 5/8 PO BARRE (B) RONDELLES DE SÉCURITÉ DE 5/16 PO BOULONS #8-32 X 7/8 PO ÉCROUS ET RONDELLES DE SÉCURITÉ #8-32 PIEDS RÉGLABLES VIS #8-32 X 3/4 PO VIS #8-32 X 1 PO
Outils requis 1 Clé anglaise et à douille de 9/16 po 1 Niveau magnétique de 12 po 1 Tournevis à pointe cruciforme #2 1 Ruban à mesurer 1 Crayon 1 Pince Pièces et matériel fournis Pièces Atelier de 48 po Atelier de 72 po Atelier de 96 po Pieds ajustables filetés 4 4 4 Longue poutre transversale 2 2 2 Longue poutre de soutien 0 0 1 Petite poutre transversale 2 2 2 Petite poutre de soutien 2 2 2 Barre (A) 2 2 2 Barre (B) 2 2 2 Boulons hexagonaux de 5/16 po x 5/8 po L 32
Assemblage de la structure 1. Prendre une barre (A) et une barre (B) et les placer à l’opposé l’une de l’autre par terre avec les étriers placés à l’extérieur des barres dans la même direction. Voir figure 1. 2.Prendre une petite poutre transversale et une petite poutre de soutien, et les boulonner à la structure avec les boulons hexagonaux de 5/16 po et les rondelles de sécurité fournis. Voir figure 1. Remarque : Les barres sur l’illustration sont montées à l’envers pour faciliter l’assemblage du plateau.
Assemblage du plateau à outils 1. Pour le plan de travail en acier inoxydable : Installer quatre vis #8 x 1 po dans les trous le long du rebord du plan de travail, à 3/4 de distance des bords. Pour le plan de travail en bambou : Aligner le plateau à outil avec le haut du plan de travail (Figure 1) et utiliser le plateau à outils comme outil de référence pour marquer le centre au-dessus des trous où mettre les 4 vis le long du rebord. (Figure 2) Percer des avant-trous de 1/16 po et insérer les vis au 3/4.
Installation de la barre d’alimentation 1. Insérer les 2 boulons #8-32 dans les fentes au dos de la barre d’alimentation. Fixer les vis dans le creux inférieur vers le cordon. 2. Installer la barre d’alimentation sur l’établi en insérant les deux vis dans les trous correspondants en avant ou sur les côtés de l’établi. 1 2 Si vous installez la barre d’alimentation à l’avant, vous pouvez passer le cordon dans les passe-fils en caoutchouc situés à l’avant et à l’arrière de l’établi. 3.
NEWAGE PRODUCTS INC. ÉTABLI SOUDÉ GARANTIE LIMITÉE DE 10 ANS OFFERTE PAR LE FABRICANT Pendant 10 ans à compter de la date d’achat, lorsque ce produit est installé, exploité et entretenu conformément aux instructions fournies avec le produit, NewAge Products Inc. remplacera les pièces ou le produit défectueux, advenant que le bris provienne d’un défaut de matériel ou de fabrication. NEWAGE PRODUCTS INC. NE PAIERA PAS POUR : 1.