Instructions / Assembly

ManualsBrandsNewAge Products ManualsStorage & OrganizationPro Series 34.5 in. H x 28 in. W x 24 in. D 1 Drawer 18-gauge Welded Steel Base Cabinet with 2-Doors

INSTALL INSTRUCTIONS

NEWAGE STEEL CABINETRY

TOOLS AND PARTS REQUIRED:

Gather the required tools and parts before starting installation.

TOOLS NEEDED:

• 7/16” wrench

• 7/16” socket driver wrench

• Adjustable wrench or pliers

• 12” Magnetic Level

• #2 Philips Bit

• Cordless Power Drill with 7/16” socket attachment

• Tape Measure

• Stud Finder

• Pencil

• Hammer Drill with Masonry Bit (optional)

WARNING:

EXCESSIVE WEIGHT HAZARD

• Use two or more people to move, assemble or install cabinet

or locker, failure to do so can result in back or other injury.

UNPACKING OF THE CABINETS:

• Begin by placing the cabinet on a sound level surface.

• Remove all cardboard and foam packaging material.

• Remove clear plastic bag.

• Dispose / recycle all packaging materials.

• Remove and verify all the contents in the box. See “Parts and

Hardware Supplied List”

NOTE: Black Caps on Sides of Base Cabinets

If you are installing cabinets beside each other, the black caps on

the sides of the base cabinets must be removed in order to allow

the cabinets to sit ﬂush beside each other, without any gaps.

Black caps can be popped out by hand or with a ﬂat screwdriver

head or pliers.

PARTS AND HARDWARE SUPPLIED WITH CABINETS:

Parts

Height-Adjustable Steel Leveling Legs

Threaded Adjustable Leveler

Nameplate

5/8” L x ¼” W Zinc Plated Hex Bolt (7/16” Hex Head

all SAE Standard Threads)

1/4” - 20 Hex Lock Nuts (7 / 16” Hex Head)

Small Lock Washers

#8 x 5/8” Wood Screw, Round Head with Washer,

Deep Thread, with Speedpoint

Drawer Keys

Full Width Adjustable Shelves

Butcher Block Support Bracket

2.5” L X ¼” W Cabinet Mounting Lag Bolts

(7/16” Hex Head)

Large Mounting Fender Washers

(1 ¼” Diameter with ¼” hole in the middle)

1-Drawer,

2-Door

Base

Cabinet

Tool

Drawer

Locker Wall

Cabinet

2-Door

Base

Cabinet

4 4 4 4 0

20 20 20 23 4

4 4 4 3 0

2 2 2 2 2

0 0 0 4 2

0 0 0 1 0

1 1 1 1 1

20 20 20 23 4

4 4 4 7 4

need more information? try, WWW.NEWAGEPRODUCTS.COM or 1 877 306 8930 for answers to commonly asked questions.

WARNING:

DO NOT OVERLOAD CABINETS! CABINETS ARE DESIGNED TO C

ARRY THE FOLLOWING MAXIMUM WEIGHT CAPACITIES:

Cabinet Shelf Weight

Capacity (lbs)

Drawer Weight

Capacity (lbs)

Bottom Weight

Capacity (lbs)

Overall Weight

Capacity

Locker 300 - 300 1200

Wall 100 - 100 200

2 Door Base - 90 300 1200

Tool Drawer - 90 300 1200

1 Drawer, 2 Door Base - 90 300 1200

Summary of content (5 pages)

PAGE 1
NEWAGE STEEL CABINETRY INSTALL INSTRUCTIONS TOOLS AND PARTS REQUIRED: WARNING: EXCESSIVE WEIGHT HAZARD Gather the required tools and parts before starting installation. • Use two or more people to move, assemble or install cabinet or locker, failure to do so can result in back or other injury.
PAGE 2
NEWAGE STEEL CABINETRY INSTALL INSTRUCTIONS ASSEMBLY INSTRUCTIONS: INSTALL THE HEIGHT-ADJUSTABLE STEEL LEVELING LEGS: (for all cabinets except for wall cabinet) 1. Open the cabinet and remove any loose shelves, closet rods, support brackets, etc. 2. Close / lock the cabinet drawers. NOTE: If you need to open the cabinet / locker doors during leveler assembly, open them slowly and do not put any weight on the open doors. This avoids damage to the cabinet hinges. 3.
PAGE 3
NEWAGE STEEL CABINETRY INSTALL INSTRUCTIONS 2. Determine which side of the locker you would prefer to have the butcher block top mounted to. 3. Once side location is determined place the butcher block side support bracket on the outside of the locker by aligning the holes in the locker with the holes in the support bracket. Ensure the bracket is positioned with the side lip pointing up. See below diagram.
PAGE 4
NEWAGE STEEL CABINETRY INSTALL INSTRUCTIONS NOTE: Make sure all shelf tabs are completely in place, see below diagram. 5. Repeat steps 2 – 4 for the remaining shelves. 6. Follow the same process for the Closet Rod by placing the two closet rod brackets on opposite sides (left and right) of the locker, and securing them to the side tabs. Then rest the long closet rod on the two brackets. See diagram. attachment.
PAGE 5
NEWAGE PRODUCTS INC. WELDED-STEEL CABINETRY WARRANTY 10 YEAR LIMITED MANUFACTURER WARRANTY For ten years from the date of purchase, when this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship. NEWAGE PRODUCTS INC. WILL NOT PAY FOR: 1.