Warning: Excessive weight hazard! Use two or more people to move, assemble or install overhead rack to avoid back or other injury. Do not leave children unattended near overhead rack. High risk of injury if installed incorrectly: Follow instructions carefully and routinely inspect your system to ensure all components are fastened securely. For assistance, call 1.877.306.8930 ; e-mail at info@newageproducts.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. Parts Supplied ItemNo PartNo Description 1 H00002A-01 M6 Flat Washer 56 2 H00004A-01 1/4-20x0.
Spare Parts ItemNo SKU Number Description 1 40494 M6 Flat Washer 2 40493 1/4-20x0.
SAFETY WARNING PLEASE READ THIS FIRST 1. All VersaRac units have a rated load capacity of 600 pounds, evenly distributed, using 3” lag bolt anchored into solid wood joists or supports capable of supporting such a load. 2. Each VersaRac utility hook can hold a maximum of 50lbs, Weight of utility hook storage must be included in maximum load of 600lbs for the overhead rack. 3. 4. Do not load more than 600lbs on to a VersaRac.
Tools Needed Rubber Mallet Magnetic Leveler Pencil Safety Glasses 3/16” Drill Bit 7/16” Socket driver wrench Stud Finder Tape Measure 7/16” socket Cordless Power Drill Ladder Manufacturer Warranty Limited Lifetime When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc.
VersaRac Installation Overview A Plan your VersaRac installation location, determine orientation and verify spacing of joists. (Page 6) Parallel B Perpendicular Install ceiling mounting angles. (Page 7 - 8) C Determine desired VersaRac height and install vertical posts (Page 9) E Install center beam and cross supports followed by wire grid platforms.
Plan the Installation Location 1 Determine if your VersaRac will be installed parallel or perpendicular to the direction of your ceiling joists. Use a stud finder to locate the joists if ceiling is finished with drywall. Parallel 2 Perpendicular Check the spacing of your ceiling joists to ensure that they will work for the size and direction of your VersaRac Install. If the spacing of your joists is 24” there should be ceiling joists located in the necessary position.
Install Ceiling Mounting Angles 3 Locate and mark the center of ceiling joist. Use a stud finder to locate the joists if ceiling is finished with drywall. 4 Align center of keyhole slots on the ceiling mounting angle with the centerline of the ceiling joist and mark the holes on both ends. 6 Install ceiling mounting angle into joist using two 1/4” x 3” lag bolts, two 1/4” washers and a 7/16” socket. 5 Pre drill 3” depth pilot holes fully into 3 inches of solid wood beam using a 3/16” drill bit.
7 Depending on the VersaRac size and orientation as determined on page 6, measure 48, 72 or 96” from the installed ceiling mounting angle to determine the location of the second ceiling mounting angles. Repeat steps 1 - 4 to install the second ceiling mounting bracket in the same orientation as the first. 8 1 2 48, 72 or 96” 4 Locate and mark the is finished center of ceiling jois with dry wall. t.
Install Vertical Angle Posts 11 Determine desired height of VersaRac from Ceiling to bottom of the overhead rack. 12 If desired height is greater than 18”, Bolt an 18” vertical angle post to a 27” post with two 1/4” x 3/4” bolts, two 1/4” lock nuts and four 1/4” washers. Use one bolt on each side of the post with keyholes in the same direction. Repeat for the remaining vertical angle posts.
Assemble and Install Perimeter Beams 14 Bolt together Long Perimeter Beams A and B at the desired 6’ or 8’ (72” or 96”) length assembly. Use four 1/4” x 3/4” bolts and 1/4” lock nuts with eight 1/4” washers per assembly. 6’ Assembly 1st Note: To reduce sag, tighten the bolts on the top of the beams first followed by the bolts on the front of the beams. 2nd 8’ Assembly 2nd 1st 15 Install both short perimeter beams into the bottom of the vertical angle posts.
17 Bolt the Center Support into the holes found in the middle of the 6’ or 8’ assembly. Use two 1/4” x 3/4” bolts and 1/4” lock nuts with four 1/4” washers per side. 18 Place the cross supports into the slots on the top of the long cross beam assemblies. Note: 19 Place both wire grids with notched corners on the ends of the VersaRac. Notched corners should provide clearance for the Vertical Angle Supports. If installing 6’ VersaRac you will have two cross supports left over.
Installation Tips Installing a Joist Hanger If the spacing of your ceiling joists do not match the desired size and direction of your VersaRac installation you will need to install a joist in the correct position. Please consult your local professional contractor for assistance installing a joist hanger. Using suitable joist hangers, install two additional wooden ceiling joists in the desired location.
Spacing VersaRac’s Never install more than one VersaRac unit on any two overhead ceiling joist supports. Installing on Slanted Ceiling Installing against Wall VersaRac can be installed on a slanted ceiling by adjusting the length of the vertical angle post assemblies. The VersaRac must be installed with a horizontally level storage platform, and vertically level vertical angle posts.
Fastening to Engineered Joists If the construction of your ceiling is using engineered ceiling joists you must install an additional ceiling joist (minimum 2” x 8”) perpendicular between two of the engineered ceiling joists.
Réglable étagère de rangement Avertissement:Risque de poids excessif! Utilisez deux ou plusieurs personnes pour déplacer , assembler ou installer porte-bagages pour éviter le dos ou d'autres blessures . Ne pas laisser les enfants sans surveillance à proximité de porte-bagages . Risque élevé de blessure si mal installé : Suivez les instructions soigneusement et régulièrement inspecter votre système pour assurer que tous les composants sont bien fixées . Pour de l’aide composez 1.877.306.
Déballage • Commencez par placer le paquet sur une surface plane recouverte. • Retirez tout carton, matériau d’emballage en mousse et des sacs en plastique transparent . • Jeter / recycler tous les matériaux d’emballage . • Vérifiez tout le contenu de la boîte et de rassembler les outils nécessaires . Voir « Pièces fournies» et « Outils nécessaires » dans la liste ci-dessous. Pièces fournies Nº d’article Nº de pièce Description 1 H00002A-01 Rondelle plate M6 56 2 H00004A-01 20 X Boulons hex.
Pièces de rechange Description Nº d’article Numéro d’UGS 1 40494 Rondelle plate M6 2 40493 20 X Boulons hex. de 0,75 po - 1/4 de po 3 4 40491 40490 20 Contre-écrous de 1/4 de po Vis autotaraudeuse à tête hex.
AVERTISSEMENT DE SÉCURITÉ PRIÈRE DE LIRE TOUT D’ABORD CECI 1. Toutes les unités VersaRac disposent d’une capacité nominale de charge de 600 libres, distribuée de manière égale, utilisant un tire-fond de 3 po ancré dans des solives en bois massif ou des supports capables de supporter une telle charge. 2. Chaque utilitaire crochet VersaRac peut contenir un maximum de 50lbs , Poids de l’utilité de stockage de crochet doit être inclus dans la charge maximale de 600lbs pour le porte-bagages . 3.
Outils nécessaires Mallot en caoutchouc Crayon 3/16” Foret 12” vérin magnétique Lunettes de protection 7/16” cle a douilles Localisateur de montants Ruban à mesurer 7/16” Douille Perceuse mecanique sans flls Échelle Garantie à vie limitée du fabricant Lorsque ce produit est installé, utilisé et entretenu conformément aux instructions ci-jointes ou fournies avec le produit, NewAge Products Inc.
VersaRac Présentation de l’installation A Planifiez votre emplacement d’installation de VersaRac , déterminer l’orientation et de vérifier l’espacement des solives . ( Page 6 ) Parallèle B Perpendiculaire Installer des angles de montage au plafond. (Page 7 - 8) C Déterminer la hauteur VersaRack désirée et installer des poteaux verticaux. (Page 9) E Installer faisceau central et supports transversaux suivis par les plates-formes de la grille métallique.
Planifier l’emplacement d’installation 1 Déterminez si votre VersaRac sera installé parallèlement ou perpendiculairement à la direction de vos solives de plafond . Utilisez un localisateur de montants pour repérer les solives si le plafond est fini avec cloisons sèches . Parallèle 2 Perpendiculaire Vérifiez l’espacement de vos solives de plafond pour veiller à ce qu’ils vont travailler pour la taille et la direction de votre VersaRac.
Installez le montage au plafond angles 3 Repérez et marquez le centre de solive du plafond . Utilisez un localisateur de montants pour repérer les solives si le plafond est fini avec cloisons sèches . 4 Alignez centre de trous de serrure sur l’angle de montage au plafond avec la ligne centrale de la solive de plafond et marquer les trous sur les deux extrémités. 6 Installez le plafond angle de montage en solive avec deux 1/4 “x 3” tirefonds , deux 1/4 “ rondelles et un 7/16” socket .
7 En fonction de la taille et de l’orientation VersaRac tel que déterminé à la page 6 , mesure 48” , 72” ou 96 “du plafond installé angle de montage pour déterminer l’emplacement du deuxième angle de montage au plafond . Répéter les étapes 1 à 4 pour installer le deuxième support de montage au plafond selon la même orientation que la première. 8 1 2 48, 72 or 96” 4 Locate and mark the is finished center of ceiling jois with dry wall. t.
Installer les montants d’angles verticaux la hauteur désirée de VersaRac 11 Déterminer du plafond au fond du etagere. 18” or 27- 42“ 12 Si la hauteur désirée est supérieure à 18 “ , Visser un «poste d’ angle vertical à un 27 “ 18 après avec deux 1/4 “x 3/4” boulons , deux 1/4 “ contre-écrous et quatre 1/4” rondelles . Utilisez un boulon sur chaque côté du poteau avec boutonnières dans la même direction .
Assembler et installer les poutres de perimeters 14 Attaches les poutres (A) et (B) à la longuer desiree, 6’ou 8’ ( 72 “ ou 96 “ ) .Utilisez quatre 1/4 “x 3/4” boulons et 1/4 “ contre-écrous avec 8 rondelles de 1/4” par assemblage. Assemblage 6’ 1er Remarque: Pour réduire l’affaissement , serrer les boulons sur le dessus des premiers faisceaux suivis par les boulons à l’avant des poutres. 2e Assemblage 8’ 2e 1er 15 Installer les poutres dans le bas des poteaux d’angle vertical .
17 19 Visser le poutre central dans les trous dans le milieu de la 6 ‘ou 8’ assemblage. Utilisez deux 1/4 “x 3/4” boulons et écrous 1/4 “ verrouiller avec quatre 1/4” rondelles de chaque côté . Placer les deux grilles métalliques avec des coins entaillés sur les extrémités de la VersaRac . Les coins entailee devraient fournir un dégagement pour l’ angle vertical.
Conseils d’installation Installation d’une poutrelle Si l’espacement de vos solives de plafond ne correspond pas à la taille désirée et la direction de votre installation VersaRac vous aurez besoin d’installer une poutrelle dans la bonne position . Utilisation des solives de plafond appropriés , installer deux solives supplémentaires de plafond en bois à l’endroit désiré .
Espacement des VersaRac’s Ne jamais installer plus d’une unité VersaRac sur les deux supports généraux de solives de plafond . Installation sur plafond incline Installer contre la mur VersaRac peut être installé sur un plafond incliné en ajustant la longueur des ensembles d’angle de poteau vertical . Le VersaRac doit être installé avec une plate-forme de stockage de niveau horizontalement et verticalement au niveau des postes d’angle vertical.
Fixation au Ingénieur Poutrelles Si la construction de votre plafond utilise les solives de plafond d’ingénierie vous devez installer un solive supplémentaire (minimum 2 “x 8”) perpendiculaire entre deux des solives de plafond d’ingénierie.