Bold Series 3.0 48in & 72in Display Wall Shelf Set Warning: Excessive weight hazard! Use two or more people to move, assemble or install shelving to avoid back or other injury. Do not leave children unattended near the shelving. High risk of injury if installed incorrectly: Follow instructions carefully and routinely inspect your system to ensure all components are fastened securely. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
Unpacking Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; email at info@newageproducts.com • Begin by placing the package on a covered flat surface. • Remove all cardboard, packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools.
Tools Needed Tape Measure 3/16” Drill Bit Stud Finder Pencil Safety Glasses 7/16” & 1/2” Socket Wrench 7/16” socket Magnetic Leveler Cordless Power Drill Ladder Manufacturer Warranty Limited Lifetime When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for the Lifetime of the product.
Weight Capacity WARNING: Do not exceed the weight capacity of the wall shelves. Each Shelf has an evenly distributed weight capacity of 250lbs. Each Shelf must be secured between two Locker or Wall Cabinets and attached to the wall. 250lbs 250lbs Display Shelf Installation: Note: Cabinets must be installed before installing display shelves 1 Ensure there is 48in/72in between the Wall Cabinets / Lockers depending on your shelf size.
3 Align the top of the shelf with the top of the Wall Cabinet / Locker and insert the 1/4” Hex bolt and washer through the mounting holes and tighten with a lock nut. Repeat to the opposite side. Note: Refer to Installation Tips for installing the top shelf upside down 4 5 Check and level before securing to Wall. Using a stud finder locate the wall studs and mark the location to drill in the Wall Shelf slot holes. www.newageproducts.
Drill a pilot hole using a 3/16” drill bit. Using a 1/4” x 2-1/2” lag bolt, one 1/4” ID Fender Washer and a 7/16” socket, bolt the Wall Shelf into the Stud. Repeat for remaning studs and second shelf. Parts Needed: Lag Bolt Lag (1/4”dia Screw x 3”) (1/4” dia x 2-1/2”) Fender Washer 7/16” Socket 7/16” socket (1/2” OD) 7 Using two M5 Phillips bolts, screw the Light Valance into the Wall Shelf hex rivet. Repeat for all remaning Light Valances.
SERIE BOLD 3.0 System de Tablettes Murale - 48po & 72po ATTENTION: Risque de poids excessif! Utilisez deux personnes ou plus pour déplacer, assembler ou installer les étagères afin d'éviter tout risque de blessure au dos ou autre. Ne laissez pas les enfants sans surveillance près des étagères. Risque élevé de blessure en cas d'installation incorrecte: suivez les instructions avec soin et inspectez régulièrement votre système pour vous assurer que tous les composants sont bien fixés.
Déballage • Commencez par placer l’emballage sur une surface plane et couverte. • Enlevez tout le carton, le matériel d’emballage et les sacs en plastique transparents. • Éliminer / recycler tous les matériaux d’emballage. • Vérifiez tout le contenu de la boîte et rassemblez les outils nécessaires. Merci d’avoir acheté un produit NewAge! S’il vous plaît appelez-nous ou visitez en ligne si vous avez des questions. Composez le 1.877.306.8930; pour UK 0800.031.4069; email à info@newageproducts.
Les outils nécessaires Ruban à measurer Foret de 3/16” Localisateur de montants Crayon Lunettes de protection 7/16” & 1/2” Clé à douille 7/16” Douille Niveau magnétique Perceuse-visseuse électrique Échelle Garantie à vie limitée du fabricant Lorsque ce produit est installé, utilisé et entretenu conformément aux instructions ci-jointes ou fournies avec le produit, NewAge Products Inc.
Capacité de poids Attention: Ne dépassez pas la capacité de poids des étagères murales. Chaque étagère a une capacité de poids uniformément répartie de 250 lb. Chaque étagère doit être fixée entre deux armoires vestiaires ou murales et fixée au mur.
3 Alignez le haut de l’étagère avec le haut de l’armoire murale / casier et insérez le boulon hexagonal 1/4 ”et la rondelle dans les trous de montage et serrez à l’aide d’un écrou de blocage. Répétez pour le côté opposé. Attention: Reportez-vous aux conseils d’installation pour installer la tablette supérieure à l’envers 4 5 Vérifiez et nivelez-le avant de le fixer au mur.
6 Percez un avant-trou avec un foret de 3/16 ”. En utilisant un tire-fond de 1/4 ”x 2-1 / 2”, une rondelle pare-choc de 1/4 ”et une douille de 7/16”, boulonnez la tablette murale dans le montant. Répétez cette procédure pour les montants restants et la deuxième étagère.