PRO3.INSTALL.REV.03 Pro 3.0 Series Warning: Excessive weight hazard! WARNING: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069; e-mail at info@newageproducts.com.
INDEX Index - 2 Guidelines and weight capacity - 2-3 Parts list - 4 Tools needed - 5 Warranty - 5 Attaching feet - 6 Attaching casters - 7 Removing and inserting drawers - 8 Installing corner cabinet - 9 Stacking cabinets - 10 Installing worktop support bracket - 11 Attaching worktop( on 2 cabinets) - 12 Installing closet rod -13 Installing shelves - 14 Securing cabinets to drywall/stud wall -15 Hanging cabinets on stud wall - 16-19 Hanging cabinets on slatwall - 20-21 Fastening cabinets together - 22 Atta
Worktop 24” Corner Worktop 56” Worktop. Fits over 2 Cabinets 84” Worktop. Fits over 3 Cabinets Weight Capacity 100 lbs. 100 lbs. Wall Cabinets Max 200 lbs. 200 lbs. 300 lbs. 300 lbs. 600 lbs. 600 lbs. 100 lbs. 100 lbs. 100 lbs. 100 lbs. 5 lbs. 500 lbs. 100 lbs. 300 lbs. 100 lbs. 200 lbs. 100 lbs. 100 lbs. 300 lbs. Split Cabinets Max 1000 lbs. Base Cabinets Max 1000 lbs. 200 lbs. Tool Cabinets Max 1000 lbs. 300 lbs. Lockers Max 1000 lbs.
Parts Supplied Muli-use Locker Hardware Box #8 x 5/8" Wood Screw 1/4" x 0.9" Fender Washer 1/4" ID x 1/2" OD Washer 1/4" Lock Nut 1/4" x 2.
Tools Needed 1 x Adjustable wrench 1 x 12” Magnetic Leveler 1 x Stud Finder 1 x Tape Measure 3 2 1 1 1 x 7/16” Socket driver wrench 1 x 8mm” Socket driver 1 x 7/16” socket wrench 2 3 1 x Set Square 1 x Pencil 1 x #2 Phillips Bit 1 x Cordless Power Drill 1 x Hammer Drill 1 x Masonry Bit 1 x #2 Phillips 1 x #3 Phillips head screw driver head screw driver [optional for masonry] Manufacturer Warranty Limited Lifetime When this product is installed, operated and maintained according to the instruct
Installing the Feet Parts Needed. 16 X Foot Attachment Screws 6 1 Open cabinet, remove any shelves or loose items. Align foot with edge of cabinet. Screw in 4 x foot attachment screws using #3 Phillips Bit Height-Adjustable Steel Leveling Legs 2 Flip cabinet upside down, locate holes at corners. 3 4 Repeat step 3 for each corner. 5 Stand & level feet.
Installing Casters Parts Needed. 4 x Casters 16 X Hex Bolt (1/4” x 5/8”) 16 X Washer (1/4”) 16 X Lock Nut (1/4”) 2 Flip cabinet upside down, locate holes forming a square. 4 Repeat step 3 for each corner. Note: Caster kits sold separately. shopnewage.com 1 Open cabinet, remove any shelves or loose items. 3 Align foot with holes. Attach with 4 hex bolts, washers, and nuts.
Installing the Drawers Inserting Drawers. Align Rails Slide In Removing Drawers.
Installing Corner Worktop Parts Needed. 4x Lock Nut (1/4”) 1 Note: Ensure there is enough assembly room. Cabinets must be assembled away from corner to access backs of cabinets. On adjacent edges attach 2 support brackets to underside of corner top using the supplied (4) 38 x 5/8” screws. 4x Washer (1/4”) 3 4x # 8 x 5/8” 4x 1/4” x 5/8 screw hex bolt 2x Support Bracket 2 1x Corner Worktop Attach top to one cabinet using 1/4” x 5/8 hex bolts, nuts, and washers.
Stacking Cabinets Parts Needed. 1 Position a second base cabinet on top of an existing base cabinet. 4 X Hex Bolt (1/4” x 5/8”) I 8 X Washer (1/4”) 4 X Lock Nut (1/4”) 2 Locate punch holes on adjoining surface and insert bolts. 4 Tighten all bolts 10 3 Attach cabinets using the supplied 1/4” x 5/8” hex bolts, washers, and nuts.
Installing Worktop Side Support Bracket Parts Needed. 2 1x Support Bracket 2 X Hex Bolt (1/4” x 5/8”) 4 X Washer (1/4”) 2 X Lock Nut (1/4”) 1 Note: Support bracket included with locker. Open locker and locate holes on either side. Align bracket. 3 Fasten nuts, bolts, and lock washers. X2 5 Level bracket and ensure it is at the same height as the base cabinet. 4 Tighten nuts & bolts.
Mounting the Worktop (On 2 Cabinets) 1 Place worktop on cabinets. 2 Locate 2 punch holes both sides. X2 X2 I 3 Drill into the worktop using the #8 x 5/8” wood screwes. Optional: For locker support bracket. X4 Use 2 washers & #8 x 5/8” wood screws. Provided in the locker packaging.
Inserting Locker Utility Rod and Hangars 1 Open cabinet Doors. 2 3 Place hangar against locker wall above supports. 4 Interior Side View 5 Lower rod into cradle. Insert clips into slots in corners. Rotate to engage. Ensure rear lange slides down behind clips and that the bracket is secure.
Inserting Cabinet Shelves 1 Stand cabinet up. 2 Insert shelf clip on slight angle and rotate to level position. 3 Insert shelf on a angle and rotate to level position. 4 Lower shelf onto supports. Interior Side View 5 Rest shelf on supports. Interior Side View 14 6 Insert remaining shelves.
Mounting Cabinets (Drywall/Studded Wall) 1 Use stud inder to locate the studs and mark the wall with a pencil. 2 Gather parts. Wall Screw (1/4” x 2.5”) Wall Washer (1/4”) Wall & Locker: 4 wall screws and 4 washers Corner Wall: 6 wall screws and 6 washers Base & Tool Cabinet: 2 wall Screws and 2 washers 3 Place cabinet tight against the wall. 6 Drill 4 wall screws and washers through perforated holes into studs. 4 Align cabinet to stud marks. X4 5 Level cabinet Masonry. • Follow steps 3 to 5.
Hanging Cabinets on Wall (optional) Use stud inder to locate the studs and mark the wall with a pencil. 1 Parts Needed. Lag Screw (1/4” x 2.5”) 2 Planning the general position of cabinets. Step A. Determine the height of the ground you would like the base and locker cabinets to be and make a horizontal mark at this position. Step B. Next mark the width of each cabinet in the intended position and ensure the wall studs fall at least 1.25” in from the edge of the cabinets.
Hanging Cabinets on Wall (cont.) Planning the general position of cabinets. (cont.) Step C. Measuring up from the line marked in Step A, make a horizontal mark at the following heights where they intersect the wall stud marks to determine where the top of the cabinet will be (and where the hanging bracket will be installed). 1. Locker: Measure 80” vertically from base line and mark at stud locations. 2. Base: Measure 32.25” vertically from base line and mark at stud locations. 3.
Hanging Cabinets on Wall (cont.) 4 Hanging cabinets on wall. Align the top of the wall hanging brackets with the lines marked for the position of the top of the cabinets(Step C) and attach the brackets securely into the studs using the supplied lag bolts and washers. Note: It is possible to ofset the bracket to one side or the other if the bracket is positioned close to the edge of the intended cabinet position by using the secondary hole positions on the bracket. C Base Cabinets 32.
Hanging Cabinets on Wall (cont.) 6 6 Parts Needed. Bolt each subsequent cabinet to the previous one using the supplied ¼” x 5/8” hex bolts and lock nuts provided in each base and wall cabinet. Hex Bolt (1/4” x 5/8”) Washer (1/4”) Lock Nut (1/4”) X4 X4 WARNING: Wall backets are not designed to support the weight of a loaded cabinet. Cabinets must be secured to the wall using supplied 1/4” x 2.5” lag screws.
Note: Securing to Wall Do not load cabinet without irst securing to the wall. Note: Brackets are not designed to support the weight of a loaded cabinet. Cabinets must be secured to the wall using supplied 1/4” x 2.5” lag screws. (4) 1/4” x 2.5” lag screws and washers secure Parts Needed. 7 Using each cabinet to wall stud from inside cabinet. LOCKER WALL STUD X4 Bolt (1/4” x 2.5”) Wall Washer (1/4”) Hanging Cabinets on Slatwall Note: Slatwall Brackets for use with standard 3” slatwall Sold Separately.
2 Attach bracket to slatwall at desired height. 3 Align bolt with slots on back of cabinet and hang cabinet . Note:For Locker cabinet attach second bracket 66” below irst bracket.For Base cabinet attach second bracket 18” below irst bracket. 4 Using 7/16” drill socket or 7/16” wrench securely tighten lock nuts to each wall bracket from inside cabinet .
Fastening Cabinets Parts Needed. 1 Note: Fasten additional cabinets to initial securely mounted cabinet. Align bolts, tighten lightly. Hex Bolt (1/4 x 5/8”) Washer (1/4”) Lock Nut (1/4”) X4 Note: Remove all drawers before fastening cabinets. 2 22 Level cabinets and tighten all bolts.
Attaching Light Valance to Wall Cabinet 1 Align holes of valance with cabinet. 3 Cross Section View 2 Insert and tighten bolt and nuts. Parts Needed.
Utility Access 1 Insert rubber grommet into cut-out hole in bottom panel. 2 Utility hole allows easy access to electrical outlet Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
