BOLD3.INSTALL.REV.05 Bold 3.0 Warning: Excessive weight hazard! WARNING: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children nearpeople cabinets.to High risk ofassemble, tipping if cabinets are installed Useunattended two or more move, or install cabinets and incorrectly: securely attach cabinets to the wall to avoid serious injury. locker to avoid back injury.
Index Index Guidelines and Weight Capacity Parts List Tools Needed Warranty Attaching Feet Attaching Casters Removing and Inserting Drawers Installing Corner Cabinet Stacking Cabinets Installing Worktop Support Bracket Attaching Worktop to Cabinets Installing Shelves Securing Cabinets to Drywall/Stud Wall Hanging Cabinets on Slatwall Fastening Cabinets Together Attaching Light Valance Utility Hole Grommet 2 2 3 3 5 5 6 7 8 9 10 11 12 13 14 15 16 18 19
Worktop 21” Corner Worktop 48” Worktop. Fits over 2 Cabinets 72” Worktop. Fits over 3 Cabinets Weight Capacity 250 lbs per foot. 1000 lbs. per Set of 4 3in Casters 600 lbs. / set of 4 150 lbs. / caster 4in Casters 1000 lbs. / set of 4 250 lbs. / caster 150 lbs. 100 lbs. Wall Cabinets Max 100 lbs. 200 lbs. 200 lbs. 200 lbs. 100 lbs. 100 lbs. 200 lbs. Base Cabinets Max 600 lbs. 100 lbs. 150 lbs. 150 lbs. 150 lbs. 100 lbs. 200 lbs. Tool Cabinets Max 600 lbs. Lockers Max 800lbs.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. Parts Supplied Type Hardware 30-in. Locker 42-in. Locker #8 x 5/8" Wood Screw 1/4" ID x 1/2" OD Washer Spring Washer 1/4" Lock Nut 1/4" x 0.9" Fender Washer Hardware Pack 1/4" x 2.
Tools Needed 1 x Adjustable wrench 1 x 12” Magnetic Leveler 1 x Stud Finder 1 x Tape Measure 3 2 1 1 1 x 7/16” Socket driver wrench 1 x 8mm” Socket driver 1 x 7/16” socket wrench 2 3 1 x Set Square 1 x Pencil 1 x #2 Phillips Bit 1 x Cordless Power Drill 1 x Hammer Drill 1 x Masonry Bit 1 x #2 Phillips 1 x #3 Phillips head screw driver head screw driver [optional for masonry] Manufacturer Warranty Limited Lifetime When this product is installed, operated and maintained according to the instruct
Installing the Feet 1 Parts Needed. 16 X Foot Attachment Screws 4 X Foot 2 Flip cabinet upside down, locate holes at corners. 3 4 Repeat step 3 for each corner. 5 6 Open cabinet, remove any shelves or loose items. Align foot with edge of cabinet. Screw in 4 x foot attachment screws using #3 philips screwdriver. Stand & level feet.
Installing Casters Parts Needed. 4 x Casters 16 X Hex Bolt (1/4” x 5/8”) 32 X Washer (1/4”) 16 X Lock Nut (1/4”) Note: Casters sold seperately. 1 2 Flip cabinet upside down, locate holes forming a square. 3 4 Repeat steps 3 for each corner. 5 Open cabinet, remove any shelves or loose items.
Installing the Drawers Inserting Drawers. Align Rails Slide In Removing Drawers.
Installing Corner Cabinet 1 Parts Needed. Lock Nut (1/4”) Wall Washer (1/4”) # 8 x 5/8” Screw 1/4” x 5/8 Hex Bolt Note: Ensure there is enough assembly room. Cabinets must be assembled away from corner to access backs of cabinets. On adjacent edges attach 2 support brackets to underside of corner top using the supplied (4) #8 x 5/8” screws. A 3 2 B 1 1 2 Attach top to one cabinet using 1/4” x 5/8 hex bolts, nuts, and washers. 4 Slide in corner and attach remaining cabinets.
Stacking Cabinets Parts Needed. 1 Position a second base cabinet on top of an existing base cabinet. 4 X Hex Bolt (1/4” x 5/8”) I 8 X Washer (1/4”) 4 X Lock Nut (1/4”) 2 Locate punch holes on adjoining surface and insert bolts. 4 Tighten all bolts 10 3 Attach cabinets using the supplied 1/4” x 5/8” hex bolts, washers, and nuts.
Installing Worktop Side Support Bracket Parts Needed. 2 Support Bracket 2 X Hex Bolt (1/4” x 5/8”) 4 X Washer (1/4”) 2 X Lock Nut (1/4”) 1 Note: Support Bracket Sold Separately A support bracket is to be used if the worktop is added to the set without a secondary supporting base/tool cabinet. Open locker and locate holes on either side. Align bracket. 3 Fasten nuts, bolts, and lock washers. X2 5 Level bracket and ensure it is at the same height as the base cabinet. 4 Tighten nuts & bolts.
Mounting the Worktop (On 2 Cabinets) 1 Place worktop on cabinets. 2 Locate 2 punch holes both sides. X2 X2 I 3 Drill into the worktop using the #8 x 5/8” wood screws. Optional: For locker support bracket. X4 Use 2 washers & #8 x 5/8” wood screws. Provided in the locker packaging.
Inserting Cabinet Shelves 1 Stand cabinet up. 2 Insert shelf at a slight angle. 3 Level shelf. 4 Lower shelf onto brackets by sliding tabs into slots. 5 Ensure shelf is clipped in position. 6 Insert remaining shelves.
Mounting Cabinets (Drywall/Studded Wall) Parts Required Wall Screw (1/4” x 2.5”) 1 Use stud finder to locate the studs and mark the wall with a pencil. Wall Washer (1/4”) Wall & Locker: 4 wall screws and 4 washers Corner Wall: 6 wall screws and 6 washers Base & Tool Cabinet: 2 wall Screws and 2 washers 2 Place cabinet tight against the wall. 5 Drill 4 wall screws and washers through perforated holes into studs. 3 Align cabinet to stud marks. X4 14 4 Level cabinet by adjusting feet Masonry.
Hanging Cabinets on Slatwall Note: Slatwall Brackets for use with standard 3” slatwall Sold Separately. Check with your slatwall supplier to determine the rated capacity of your slatwall. DO NOT OVERLOAD. NewAge Slatwall Brackets are only compatible with standard 3” on center Slatwall. 1 Parts Needed. 3 X Hex Bolt (1/4” x 5/8”) Insert bolts through slatwall bracket. Slatwall Bracket 3x Wall Washer (1/4”) 3x Lock Nut (1/4”) 2 Attach braket to slatwall at desired height.
Fastening Cabinets Parts Needed. 1 Note: Fasten additional cabinets to initial securely mounted cabinet. Align bolts, tighten lightly. Hex Bolt (1/4” x 5/8”) Washer (1/4”) Lock Nut (1/4”) X4 X4 Note: Remove all drawers before fastening cabinets 2 16 Level cabinets and tighten all bolts.
Attaching Light Valance to Wall Cabinet 1 Align holes of valance with cabinet. 3 Cross Section View 2 Insert and tighten bolt and nuts. Parts Needed.
Utility Access 1 Insert rubber grommet into cut-out hole in bottom panel. 2 The utility access hole allows easy connection to power outlet. Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
