HOME BAR SERIES 3 DRAWER BASE Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts.com.
Weight Capacity Countertops Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. 220 lbs. Parts Supplied 3 Drawer Cabinet 55lbs. 55lbs. 48” Countertop. Fits over 2 Cabinets 55lbs. 72” Countertop. Fits over 3 Cabinet 55lbs. 96” Countertop.
Installing the Handles 1 3 Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 3 x Handle Note: Align handle to holes on doors or drawers. Removing Drawer 4 Extend drawer fully. 6 Tilt and remove shelf rack. 5 Press plastic triggers on underside of drawer according to arrows in image. 6 x Handle Bolt (M4x 30mm) Screw in bolts. Inserting Drawer 10 3 Partially extend drawer slides.
Fastening Cabinets 9 Parts Needed. 10 Note: All drawers must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 12 Parts Needed. 13 Place worktop over cabinets and lower onto cabinets. 4 - #8 x 25mm screws 4 - #8 x 25mm screws 11 Mounting the Worktop 14 Using pilot hole as guides, screw into second cabinet. Do not over-tighten screws and punch through other side! Drill 3/32” pilot holes on interior roof of cabinet.
Weight Capacity Countertops (for Base cabinets only.) 50lbs. 50lbs. HOME BAR SERIES WALL WINE RACK Warning: ExcessiveExcessive weight hazard! Warning: weight hazard! Use two or more people to move, assemble or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for UK 0800.031.
Unpacking Installing the Handles Note: Cabinets come with handles installed on inside of drawers/doors. • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. 1 • Dispose / recycle all packaging materials. 2 Parts Needed. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Mounting Cabinets 7 Use stud finder to locate the studs and mark the wall with a pencil. Fastening Cabinets 8 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 9 4 Gather parts. 5 Remove wine rack to make attaching cabinets easier. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. LED Light Guide 12 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. LED Light with power Adapter SKU# 60836/60838 A 13 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. The adapter kit is used to connect to the electrical outlet, and contains the power on/ off switch for the LED lights.
Installing LED Lights for Wall Cabinets 1 Method 1. Using double sided tape provided. Attach double sided tape to back of LED light bar. Peel backing off. 2 Center and press firmly 5.5”, in from walls and 7.5”, in from back wall. 5.5” 7.5” 3 Feed connector cable through pre-drilled holes on tops of cabinet and connect at ends of LED light strips. 3 Installing LED Lights for Wall Cabinets cont. 4 Method 2. Using clips provided. Predrill 3/32 holes, 8.5” in from side walls and 8” in from back wall.
HOME BAR SERIES SHORT WALL DISPLAY Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts.com.
Weight Capacity Countertops (for Base cabinets only) Unpacking • • • • 50lbs. 25 lbs. • 48” Countertop. Fits over 2 Cabinets Tall Wall Display Cabinet Threaded Caps 4 Threaded Washer 4 Handles 2 Handle Bolts ( M4 x 22mm) 2 #8 x 25mm Screws 4 Lag Screw ( 6 mm x 55 mm) 4 Glass Shelves 2 10 Shelf Pins 25 lbs. 72” Countertop. Fits over 3 Cabinets 50lbs. 96” Countertop. Covers over 4 Cabinets Short Display Cabinet Max 150lbs. Begin by placing the package on a covered flat surface.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handle Note: Align handle to holes on doors or drawers. Inserting Glass Shelves 4 Open cabinet doors. Install shelf pins at desired height. 5 Ensure pins are installed at level height. 6 Insert glass shelf at a slight angle. 7 Position over shelf supports . 8 Lower shelf down onto shelf supports. 9 Repeat steps 1-4 for second shelf.
Mounting Cabinets 10 Use stud finder to locate the studs and mark the wall with a pencil. Fastening Cabinets 11 Gather parts. 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 12 15 16 All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 18 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. LED Light Guide LED Light with power Adapter SKU# 60836/60838 A 19 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. The adapter kit is used to connect to the electrical outlet, and contains the power on/ off switch for the LED lights.
Installing LED Lights for Wall Cabinets 1 Method 1. Using double sided tape provided. Attach double sided tape to back of LED light bar. Peel backing off. 2 Center and press firmly 5.5”, in from walls and 7.5”, in from back wall. 5.5” 7.5” 3 Feed connector cable through pre-drilled holes on tops of cabinet and connect at ends of LED light strips. 3 Installing LED Lights for Wall Cabinets cont. 4 Method 2. Using clips provided. Predrill 3/32 holes, 8.5” in from side walls and 8” in from back wall.
HOME BAR SERIES TALL WALL DISPLAY Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts.com.
Weight Capacity Countertops (for Base cabinets only.) Unpacking • • • • 50lbs. 25lbs. • Begin by placing the package on a covered flat surface. Remove all cardboard, foam packaging material and clear plastic bags. Dispose / recycle all packaging materials. Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. 48” Countertop. Fits over 2 Cabinets 25lbs.
Installing the Handles 1 3 Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handle Note: Align handle to holes on doors or drawers. Inserting Glass Shelves 1 Open cabinet doors. Attach shelf clips to desired height. 2 Ensure clips are at level height. 3 Insert glass shelf at a slight angle. 4 Position over shelf supports . 5 Lower shelf down onto shelf supports. 6 Repeat steps 1-4 for all shelves. 2 x Handle Bolt M4 x 22mm Screw in bolts.
Mounting Cabinets 7 Use stud finder to locate the studs and mark the wall with a pencil. Fastening Cabinets 8 12 Gather parts. Parts Needed. 13 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x25mm screws 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 9 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 15 LED Light Guide To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. LED Light with power Adapter SKU# 60836/60838 A 16 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. The adapter kit is used to connect to the electrical outlet, and contains the power on/ off switch for the LED lights.
Installing LED Lights for Wall Cabinets 1 Method 1. Using double sided tape provided. Attach double sided tape to back of LED light bar. Peel backing off. 2 Center and press firmly 5.5”, in from walls and 7.5”, in from back wall. 5.5” 7.5” 3 Feed connector cable through pre-drilled holes on tops of cabinet and connect at ends of LED light strips. 3 Installing LED Lights for Wall Cabinets cont. 4 Method 2. Using clips provided. Predrill 3/32 holes, 8.5” in from side walls and 8” in from back wall.
HOME BAR SERIES SPLIT CABINET Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts.com.
Weight Capacity Countertops Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. Parts Supplied 220 lbs. 55 lbs. 25 lbs. 200 lbs. Split Base Cabinet Max 500 lbs. 48” Countertop. Fits over 2 Cabinets 72” Countertop. Fits over 3 Cabinets 96” Countertop.
Installing Drawer Handle 1 1x Handle 3 2 Parts Needed. Screw in bolts. Note: Cabinets come with handles installed on inside of drawers/ doors. Align handle to holes on doors or drawers. Installing the Handles 4 2x Drawer Handle Bolt M4 x 30mm 2 x Handles 6 5 Parts Needed. Screw in bolts. 4 x Door Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Inserting Shelf 1 3 Open cabinet doors. Attach shelf clips to desired height. Insert shelf at a slight angle. Removing Drawer 2 4 7 Extend drawer fully. 9 Tilt and remove shelf rack. 8 Ensure clips are at level height. Press plastic triggers on underside of drawer according to arrows in image. Position over shelf supports . Lower shelf down onto shelf supports. Inserting Drawer 5 10 3 Partially extend drawer slides.
Fastening Cabinets 12 Parts Needed. 13 Note: All shelves and drawers must be removed prior to fastening cabinets together. Drill 3/32 pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws Mounting the Worktop 15 Place worktop over cabinets and lower onto cabinets. 4 - #8 x 25mm screws pilot hole as guides, screw into second cabinet. 14 Using Do not over-tighten screws and punch through other side! 16 Drill 4, 3/32” pilot holes on interior roof of cabinet.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 18 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 19 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. B Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
HOME BAR SERIES DISPLAY CABINET Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts.com.
Weight Capacity Countertops Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below. Parts Supplied 220lbs. 25 lbs. 48” Countertop. Fits over 2 Cabinets 25 lbs. 72” Countertop. Fits over 3 Cabinet 25 lbs. 205 lbs.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handles Note: Align handle to holes on doors or drawers. Fastening Cabinets 4 Parts Needed. 5 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4- #8 x25mm screws 4 x Handle Bolt M4 x 22mm 6 Using pilot hole as guides, screw into second cabinet.
Mounting the Worktop 7 Parts Needed. 8 Inserting Cabinets Shelves on an angle Place worktop over cabinets and lower onto cabinets. 11 Open cabinet doors. Attach shelf clips to desired height. 13 4 Insert rack at a slight angle and position over shelf supports. 15 Ensure shelf supports sits in groove on lower edge of rack. 12 The shelf supports are inserted into front and middle hole positions. 4- #8 x25mm screws 9 Drill 3/32” pilot holes on interior roof of cabinet.
Inserting Cabinets Shelves Horizontal 17 Open cabinet doors. Attach shelf clips to desired height. 18 The shelf supports are inserted into front and back holes. Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 23 19 Insert rack at a slight angle and position over shelf supports. 20 Lower shelf down onto shelf supports. A 24 21 Lower shelf down onto shelf supports.
Installing LED Lights for Display Cabinets cont. LED Light Guide 3 For bottom Display cabinet drill holes on back panel following Diagram 1. The hole can be placed on either side of cabinet at point A. or B., depending on outlet location. Using installation method from Steps 2 or 5 above center and install LED light 3 - 4 inches in from front. 1.
