HOME BAR SERIES CABINETS 2 Door Cabinet Display Cabinet Wall Wine Rack Split Double Display Cabinet Wine Storage Cabinet Short Wall 3 Drawer Cabinet Tall Wall SHELVING 63” Shelf 42” Shelves COUNTERTOPS 84” Countertop 63” Countertop 42” Countertop
HOME BAR SERIES 21in. 2 DOOR CABINET Warning: Excessive weight hazard! ! STOP Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts. com.
Weight Capacity Countertops 220lbs. 42” Countertop. Fits over 2 Cabinets 25 lbs. 63” Countertop. Fits over 3 Cabinet 205 lbs. Bottle Display Base Cabinet Max 500lbs. 84” Countertop.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handles Note: 4 x Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Fastening Cabinets 4 Parts Needed. 5 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4- #8 x25mm screws 6 Using pilot hole as guides, screw into second cabinet.
Inserting Cabinets Shelves on an angle 11 Open cabinet doors. Attach shelf clips to desired height. 13 4 Insert rack at a slight angle and position over shelf supports. Rotate shelf so it is level. 15 Rest shelf on shelf supports 12 16 Make sure shelf supports are located at the same height. 14 Lower shelf down onto shelf supports. Insert remaining shelves.
HOME BAR SERIES 21in. DISPLAY CABINET Warning: Excessive weight hazard! ! STOP Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts. com.
Weight Capacity Countertops 220lbs. 25 lbs. 42” Countertop. Fits over 2 Cabinets 25 lbs. 63” Countertop. Fits over 3 Cabinet 25 lbs. 205 lbs. Bottle Display Base Cabinet Max 500lbs. 84” Countertop.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handles Note: 4 x Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Fastening Cabinets 4 Parts Needed. 5 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4- #8 x25mm screws 6 Using pilot hole as guides, screw into second cabinet.
Inserting Cabinets Shelves on an angle 11 Open cabinet doors. Attach shelf clips to desired height. 13 4 Insert rack at a slight angle and position over shelf supports. 15 Ensure shelf supports sits in groove on lower edge of rack. 12 The shelf supports are inserted into front and middle hole positions. 14 16 Lower shelf down onto shelf supports. Insert remaining shelves.
Inserting Cabinets Shelves Horizontal 17 Open cabinet doors. Attach shelf clips to desired height. 19 Insert rack at a slight angle and position over shelf supports. 21 Lower shelf down onto shelf supports. 18 The shelf supports are inserted into front and back holes. 20 22 Lower shelf down onto shelf supports. Insert remaining shelves.
HOME BAR SERIES 42in. DISPLAY CABINET Warning: Excessive weight hazard! ! STOP Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@newageproducts. com.
Weight Capacity Countertops 220lbs. 220lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 25 lbs. 205 lbs. 205 lbs. Bottle Display Base Cabinet Max 500lbs. 42” Countertop. Fits over 2 Cabinets 63” Countertop. Fits over 3 Cabinet 84” Countertop.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 4 x Handles Note: 8 x Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Fastening Cabinets 4 Parts Needed. 5 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4- #8 x25mm screws 6 Using pilot hole as guides, screw into second cabinet.
Mounting the Worktop 7 Parts Needed. 8 Place worktop over cabinets and lower onto cabinets. 4- #8 x25mm screws 9 Drill 3/32” pilot holes on interior roof of cabinet. 10 3 Tighten screws to secure cabinets.
Inserting Cabinets Shelves on an angle 11 Open cabinet doors. Attach shelf clips to desired height. 13 4 Insert rack at a slight angle and position over shelf supports. 15 Ensure shelf supports sits in groove on lower edge of rack. 12 The shelf supports are inserted into front and middle hole positions. 14 16 Lower shelf down onto shelf supports. Insert remaining shelves.
Inserting Cabinets Shelves Horizontal 17 Open cabinet doors. Attach shelf clips to desired height. 19 Insert rack at a slight angle and position over shelf supports. 21 Lower shelf down onto shelf supports. 18 The shelf supports are inserted into front and back holes. 20 22 Lower shelf down onto shelf supports. Insert remaining shelves.
HOME BAR SERIES 21in. TALL WALL DISPLAY Warning: Excessive weight hazard! ! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@ newageproducts.com.
Weight Capacity Countertops (for Base cabinets only.) 30lbs. 20lbs. 42” Countertop. Fits over 2 Cabinets 20lbs. 63” Countertop. Fits over 3 Cabinets 20 lbs. 30 lbs. Tall Display Cabinet Max 120 lbs. 84” Countertop.
Unpacking • • • • • Begin by placing the package on a covered flat surface. Remove all cardboard, foam packaging material and clear plastic bags. Dispose / recycle all packaging materials. Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handle Note: 2 x Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Inserting Glass Shelves 1 Open cabinet doors. Attach shelf clips to desired height. 2 Ensure clips are at level height. 3 Insert glass shelf at a slight angle. 4 Position over shelf supports . 5 Lower shelf down onto shelf supports. 6 Repeat steps 1-4 for all shelves.
Mounting Cabinets 7 Use stud finder to locate the studs and mark the wall with a pencil. 8 Gather parts. 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 9 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet. Pilot Holes Place cabinet flush against wall and attach using screws and washers. Wall Studs Wall Studs 10 11 Use threaded caps to cover screws.
Fastening Cabinets 12 Parts Needed. 13 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x25mm screws 14 Using pilot hole as guides, screw into second cabinet.
HOME BAR SERIES 21”WALL WINE RACK ! Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@ newageproducts.com.
Weight Capacity Countertops (for Base cabinets only.) 40lbs. 42” Countertop. Fits over 2 Cabinets 30lbs. 63” Countertop. Fits over 3 Cabinet 30 lbs. 84” Countertop. Fits over 4 Cabinet Wall Wine Rack Max 100 lbs.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handle Note: 4 x Handle Bolt M4 x 22mm Screw in M4 x 22mm bolts. Align handle to holes on doors or drawers.
Mounting Cabinets 4 Use stud finder to locate the studs and mark the wall with a pencil. Note: Remove wine rack to make attaching cabinets easier. 5 Gather parts. 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 6 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet. Pilot Holes Place cabinet flush against wall and attach using screws and washers.
Fastening Cabinets 9 Parts Needed. 4 - #8 x 25mm screws 11 10 Note: Remove wine rack to make attaching cabinets easier. Drill 3/32” pilot holes on interior wall of cabinet being fastened. X4 Using pilot hole as guides, screw into second cabinet.
Tip-over Hazard Only open one drawer at a time. If this cabinet is installed on its own, it must be fastened to a permanent structure. HOME BAR SERIES 21” 3 DRAWER BASE ! Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.
Weight Capacity Countertops 220 lbs. 55lbs. 42” Countertop. Fits over 2 Cabinets 55lbs. 63” Countertop. Fits over 3 Cabinet 55lbs. 84” Countertop. Fits over 4 Cabinet 3 Drawer Base Cabinet Max 440 lbs.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 3 x Handle Note: 6 x Handle Bolt (M4x 30mm) Align handle to holes on doors or drawers.
Removing Drawer 4 Extend drawer fully. 6 Tilt and remove shelf rack. 5 Press plastic triggers on underside of drawer according to arrows in image. Inserting Drawer 7 3 Partially extend drawer slides. 8 Put drawer on slides and slide each drawer slide forward until you hear a click sound.
Fastening Cabinets 9 Parts Needed. 10 Note: All drawers must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 11 Using pilot hole as guides, screw into second cabinet. Do not over-tighten screws and punch through other side! X4 Securing Cabinet to Wall to prevent tipping 12 To securely fasten the cabinet to the wall, drill 1/4” pilot holes on back inside wall of cabinet.
Tip-over Hazard Only open one drawer at a time. If this Cabinet is installed on its own please fasten to a permanent structure. HOME BAR SERIES 21in. SPLIT CABINET Warning: Excessive weight hazard! ! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.
Weight Capacity Countertops 220 lbs. 30 lbs. 42” Countertop. Fits over 2 Cabinets 25 lbs. 63” Countertop. Fits over 3 Cabinets 200 lbs. 84” Countertop. Fits over 4 Cabinets Split Base Cabinet Max 500 lbs.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing Drawer Handle 1 1x Handle 3 2 Parts Needed. Screw in bolts. 2x Drawer Handle Bolt M4 x 30mm Note: Cabinets come with handles installed on inside of drawers/ doors. Align handle to holes on doors or drawers.
Installing the Handles 4 2 x Handles 6 5 Parts Needed. Screw in bolts. 4 x Door Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Inserting Shelf 1 Open cabinet doors. Attach shelf clips to desired height. 2 Ensure clips are at level height. 3 Insert shelf at a slight angle. 4 Position over shelf supports . Lower shelf down onto shelf supports.
Removing Drawer 6 Extend drawer fully. 8 Tilt and remove shelf rack. 7 Press plastic triggers on underside of drawer according to arrows in image. Inserting Drawer 9 3 Partially extend drawer slides. 10 Put drawer on slides and slide each drawer slide forward until you hear a click sound.
Fastening Cabinets 11 Parts Needed. 12 Note: All shelves and drawers must be removed prior to fastening cabinets together. Drill 3/32 pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 11 Using pilot hole as guides, screw into second cabinet. Do not over-tighten screws and punch through other side! X4 Securing Cabinet to Wall to prevent tipping 12 To securely fasten the cabinet to the wall, drill 1/4” pilot holes on back inside wall of cabinet.
HOME BAR SERIES 21in. WINE STORAGE Warning: Excessive weight hazard! ! Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@ newageproducts.com.
Weight Capacity Countertops 220 lbs. 30 lbs. 42” Countertop. Fits over 2 Cabinets 25 lbs. 63” Countertop. Fits over 3 Cabinets 200 lbs. 84” Countertop. Fits over 4 Cabinets Split Base Cabinet Max 500 lbs.
Unpacking • Begin by placing the package on a covered flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 4 2 x Handles 6 5 Parts Needed. Screw in bolts. 4 x Door Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Inserting Shelf 1 Open cabinet doors. Attach shelf clips to desired height. 2 Ensure clips are at level height. 3 Insert shelf at a slight angle. 4 Position over shelf supports . Lower shelf down onto shelf supports.
Fastening Cabinets 11 Parts Needed. 12 Note: All shelves and drawers must be removed prior to fastening cabinets together. Drill 3/32 pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 11 Using pilot hole as guides, screw into second cabinet. Do not over-tighten screws and punch through other side! X4 Securing Cabinet to Wall to prevent tipping 12 To securely fasten the cabinet to the wall, drill 1/4” pilot holes on back inside wall of cabinet.
HOME BAR SERIES 21in. SHORT WALL DISPLAY Warning: Excessive weight hazard! ! STOP Use two or more people to move, assemble, or install cabinets to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed incorrectly: securely attach cabinets to the wall to avoid serious injury. For assistance, call 1.877.306.8930; for U.K 0800.031.4069: e-mail at info@ newageproducts.com.
Weight Capacity Countertops (for Base cabinets only) 40lbs. 20 lbs. 42” Countertop. Fits over 2 Cabinets 20 lbs. 63” Countertop. Fits over 3 Cabinets 30lbs. 84” Countertop. Fits over 4 Cabinets Short Display Cabinet Max 130lbs.
Unpacking • • • • • Begin by placing the package on a covered flat surface. Remove all cardboard, foam packaging material and clear plastic bags. Dispose / recycle all packaging materials. Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 3 Screw in bolts. Cabinets come with handles installed on inside of drawers/doors. 2 Parts Needed. 2 x Handle Note: 4 x Handle Bolt M4 x 22mm Align handle to holes on doors or drawers.
Inserting Glass Shelves 4 Open cabinet doors. Install shelf pins at desired height. 5 Ensure pins are installed at level height. 6 Insert glass shelf at a slight angle. 7 Position over shelf supports . 8 Lower shelf down onto shelf supports. 9 Repeat steps 1-4 for second shelf.
Mounting Cabinets 10 Use stud finder to locate the studs and mark the wall with a pencil. 11 Gather parts. 4 x Lag Screw 4 x Threaded Washer 6mm x 55mm 12 4 x Threaded Caps Near the top of the cabinet, drill 1/4” holes through the back of the cabinet that are in line with marked studs. Repeat for drilling two holes near the bottom of the cabinet. Pilot Holes Place cabinet flush against wall and attach using screws and washers. Wall Studs Wall Studs 13 14 Use threaded caps to cover screws.
Fastening Cabinets 15 Parts Needed. 16 Note: All shelves must be removed prior to fastening cabinets together. Drill 3/32” pilot holes on interior wall of cabinet being fastened. 4 - #8 x 25mm screws 17 Using pilot hole as guides, screw into second cabinet.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 18 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 19 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. B Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
Mounting the Worktop 13 Place worktop over cabinets and lower onto cabinets. 4 - #8 x 25mm screws 14 Drill 4, 3/32” pilot holes on interior roof of cabinet. 15 3 Tighten screws to secure cabinets.
LED Light Guide LED Light with power Adapter SKU# 60836/60838 The adapter kit is used to connect to the electrical outlet, and contains the power on/ off switch for the LED lights. It is used when one single light unit is needed or as the first light used when linking multiple light units together. It controls on/off power for all light units linked to it. Includes adapter, LED light, plastic clips, and double sided tape.
Installing LED Lights for Display Cabinets 1 2 3 Method 1. Using double sided tape provided. Attach double sided tape to back of LED light bar. Peel backing off. For bottom Display cabinet drill holes on back panel following Diagram 1. The hole can be placed on either side of cabinet at point A. or B., depending on outlet location. Using installation method from Steps 2 or 5 above center and install LED light 3 - 4 inches in from front. 1.5” 1.5” A 3/8”Dia. B Diagram 1.
LED Light Guide LED Light with power Adapter SKU# 60836/60838 The adapter kit is used to connect to the electrical outlet, and contains the power on/ off switch for the LED lights. It is used when one single light unit is needed or as the first light used when linking multiple light units together. It controls on/off power for all light units linked to it. Includes adapter, LED light, plastic clips, and double sided tape.
Installing LED Lights for Wall Cabinets 1 Method 1. Using double sided tape provided. Attach double sided tape to back of LED light bar. Peel backing off. 2 Center and press firmly 5.5”, in from walls and 7.5”, in from back wall. 5.5” 7.5” 3 Feed connector cable through pre-drilled holes on tops of cabinet and connect at ends of LED light strips. Installing LED Lights for Wall Cabinets cont. 4 Method 2. Using clips provided. Predrill 3/32 holes, 8.5” in from side walls and 8” in from back wall.
Manufacturer One Year Limited Warranty When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of One Year from the purchase date of the product. NEWAGE PRODUCTS INC. WILL NOT PAY FOR: 1.
Shelf_ INSTALL 1.0 63” Shelf 42” Shelves 72” Shelf 48” Shelves HOME BAR SHELF SYSTEM WARNING: ! Use two or more people to move, assemble or install the shelf system to avoid back or other injury. Follow instructions carefully and routinely inspect your system to ensure all components are fastened securely. For assistance, call 1.877.306.8930; for U.K 0800.031.4069; e-mail at info@newageproducts.com.
Index Tools Needed/ Weight Capacity Warranty 4 Parts Supplied 5 Installing Shelf System to drywall 3 6-7 Unpacking • • • • Begin by placing the package on a covered flat surface. Remove all cardboard, foam packaging material and clear plastic bags. Dispose / recycle all packaging materials. Verify all the contents in the box and gather the required tools. See “Tools Needed”, and “Parts Supplied” list.
Tools Needed 1 x 24"-48" Level 1 x Cordless Power Drill 1 x #2 Phillips head screwdriver 1 x Stud Finder 1 x Tape Measure 1 x Pencil 1 x #2 Phillips Bit 1x 3 mm or 1/8” Drill Bit 1x 2.
Parts Supplied 42" Floating Shelf 42" Floating Wine Glass Shelf 63" Floating Shelf 48" Floating Shelf Shelf 1 1 1 1 1 Lag Screws (6mm x 55mm) 2 2 3 2 2 3 Threaded Washers 2 2 3 2 2 3 Threaded screw cover 2 2 3 2 2 3 Lag Screw 48" Floating Wine Glass Shelf Threaded Screw Cover 42” Shelf System 72" Floating Shelf 1 Threaded Washer 63” Shelf System 42” Floating Shelf 63” Floating Shelf 42” Floating Wine Glass Shelf 48” Shelf System 48” Floating Shelf 48” Floating Wine
Fastening the Shelf System to drywall 1 Use stud finder to locate the studs and mark the wall with a pencil. 3 Begin by measuring up from the countertop to the desired height of the shelf position. Using a level, mark a horizontal line. Mark a vertical line centered on each stud perpendicular to the horizontal pencil line. Diagram (A). 2 The shelf system must be secured to wall studs.
Fastening the Shelf System to drywall 7 5 Using a 1/4 “ drill bit , pre-drill through the shelf backer and into the wall stud. The 63” length shelf must be fastened with minimum three lag screws, the 42” length shelf must be fastened with minimim 2 lag screws 6 Using a #2 Phillips head screwdriver fasten the shelf to the wall with lag screws and threaded washers. 7 Finish by screwing on the threaded screw head cover.
Manufacturer One Year Limited Warranty When this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship for a period of One Year from the purchase date of the product. NEWAGE PRODUCTS INC. WILL NOT PAY FOR: 1. 2.
