32”2 Door Stainless Steel 65000 33” Insert Grill Stainless Steel 65004 32” Bar Cart 65007 32” SINK Stainless Steel 65001 32” 3 Drawer Stainless Steel 65002 45 Degree Stainless Steel Set 65005 32” Bar Stainless Steel 65003 90 Degree Shelf Stainless Steel 65006 64” Prep Table 65008 OUTDOOR KITCHEN Stainless Steel Sets Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury.
OUTDOOR KITCHEN 32”2 Door Cabinet SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65000-INSTL-01-Rev.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 115 lbs. 115 lbs. 200 lbs. 32" - 2 Door Cabinet Max 630 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 64" Worktop. Fits over 2 Cabinets 88" Worktop. Fits over 2 Cabinets & Fridge nook. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handle 3 2 Parts Needed. Screw in bolts. Handle Bolt M4 x 30mm Align handle to holes on doors or drawers.
Installing the Legs Parts Needed. 4 X Adjustable Feet 2 1 Open cabinet, remove any shelves or loose items. 3 Align leg with rivet nuts on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down, locate holes on crossbeam. 3 1 4 Repeat step 3 for each corner. 5 4 2 Stand cabinet upright. To level and adjust legs go to next step.
Levelling the Legs Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Glide Wrench 2 Rotate wrench to lower or raise corner of cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Installing the Casters(optional) Parts Needed. 4 X Casters 2 1 Open cabinet, remove any shelves or loose items. 3 Align caster with holes on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down on protected surface and locate holes on crossbeam. 3 4 1 2 4 Repeat step 3 to install all casters 5 Stand cabinet upright.
Fastening Cabinets(to each other) 1 4 X Hex Nut(M5) 3 2 Parts Needed. Remove plastic caps from cabinets. 4 X Hex Bolt (M5 x 50mm”) X8 Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Mounting the Worktop 1 Stand cabinet upright. 2 Place worktop over cabinets. 3 Insert the worktop bolt heads into the keyhole shape slots. 4 Push worktop in to lock. Tighten screws to secure cabinets. Optional: Repeat steps 2-5 for mounting larger worktops.
Inserting Cabinet Shelves 1 Open cabinet doors. Attach shelf clips to desired height. 2 Begin with shelf being level. 3 Insert and position above shelf clips. 4 Lower shelf down onto shelf clips. 5 Install remaining shelves.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise. B Thank you for purchasing a NewAge Product! Please give us a call or visit online if you have any questions. Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.
Tip-over Hazard Only open one drawer at a time. If this Cabinet is installed on its own please fasten to a permanent structure. OUTDOOR KITCHEN 32"-3 Drawer Cabinet SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65002-INSTL-01-Rev.
Weight Capacity Worktops 200 lbs. 56” Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 75 lbs. 75 lbs. 32” - 3 Drawer Cabinet Max 425 lbs. 64” Worktop. Fits over 2 Cabinets 88” Worktop. Fits over 2 Cabinets & Fridge nook. 96” Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Drawers Removing Drawers. Right Side Left Side Slide Out Inserting Drawers.
Installing the Handles 1 Handles 3 2 Parts Needed. Screw in bolts. Handle Bolts (M4 x 30mm) Align handle to holes on doors or drawers.
Installing the Legs 1 Parts Needed. 4 X Adjustable Legs 2 Remove Drawers, remove loose items. 16 X Hex Washer Bolt Flip cabinet upside down, locate holes on crossbeam. 3 Align foot with rivet nuts on crossbeam. Tighten Hex bolts . 3 4 1 2 4 Repeat steps 1-3 for each corner. 5 Stand cabinet upright. To level and adjust feet go to next step.
Levelling the Feet Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Leg Wrench 2 Rotate wrench to lower or raise corner of cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Installing the Casters(optional) 1 Parts Needed. 4 X Casters 2 Open cabinet, remove drawers or loose items. 16 X Hex Washer Bolt Flip cabinet upside down, locate holes on crossbeam. 3 Align foot with holes on crossbeam. Screw in Hex bolts with washer and lock washer. 3 4 1 2 4 Repeat steps 2-3 for each corner. 5 Stand cabinet upright.
Note: Fastening Cabinets 1 3 2 Parts Needed. 4 X Hex Nut (M5) All drawers must be removed prior to fastening cabinets together. Remove plastic caps from cabinets. X8 4 X Hex Bolt (M5 x 50mm) Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Mounting the Worktop 1 Stand cabinet. 2 Place worktop over cabinets. 3 Insert the worktop bolt heads into the keyhole shape slots. 4 Push worktop in to lock. Tighten bolts to secure cabinets. Optional: Repeat steps 2-5 for mounting larger worktops.
*Rear View Shown OUTDOOR KITCHEN 45˚ Cabinet SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65005-INSTL-01-Rev.
Weight Capacity 100 lbs. 50 lbs. 50 lbs. 100 lbs. 45˚ Cabinet Max 300 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handle 3 2 Parts Needed. Screw in bolts. Handle Bolt M4 x 30mm Align handle to holes on doors or drawers.
Installing the Feet Parts Needed. 3 X Adjustable Feet 2 4 1 Flip cabinet upside down, locate holes on crossbeam. 3 Repeat step 2 for each leg. 16 x Hex Washer Bolt Alignleg with holes on crossbeam. Fasten in Hex bolts with washer and lock washer. Stand cabinet upright. To level and adjust legs go to next step.
Levelling the Legs Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Leg Wrench 2 Rotate wrench to lower or raise corners of the cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Fastening Cabinets 1 4 X Hex (1/4) 3 2 Parts Needed. Remove plastic caps from cabinet. 4 X Hex Bolt (1/4 x 2”) X8 Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
OUTDOOR KITCHEN 64"Prep Table SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65008-INSTL-01-Rev.
Weight Capacity 200 lbs. 64" - PREP TABLE Max 200 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Table Assembly Parts Needed. 1 Insert Leg Frame into cross rails. Using M6 bolts to fasten the leg frame to cross rails.
Table to Cabinet Ganging Parts Needed. 4 x Hex Bolt (M6x 30) 1 Align inserts in Table Leg Frame with with 4 Holes in side of Cabinet. Fasten 4 x 4mm x 40 mm Hex Bolts as shown. Note: Table has rivet nuts in legs to thread into. Insert bolt from cabinet side.
Table to Table Ganging Parts Needed. 4 X Pan Head Bolts (M4 x 13mm) 1 4 x Ganging Brackets Washers (M4) 2 Using 4 Ganging Brackets and 2 x M4 Pan Head bolts per each bracket. Attach two tables together. 3 Position Brackets over existing bolt heads using clearance holes. On a Flat Protected Surface flip over two tables and align them right to left sides as shown.
OUTDOOR KITCHEN 90˚ Corner Shelf SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65006-INSTL-01-Rev.
Weight Capacity 50 lbs. 50 lbs. 100 lbs. 90° Corner Shelf Max 200 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Frame Assembly Parts Needed. Hex Washer Bolt (M6 x 25mm) 2 4 1 Attach 2 legs to leg channel with 8 x M6 x25mm hex bolts. 3 Attach 2 uprights to assembly using 4 x 8/32” x 3/8” pan head bolts Pan Head Bolt (30 x 8/32 x 3/8”) Attach Top, Back Panel and Base with 4 x 8/32” x 3/8”pan head bolts. Attach shelf to vertical supports using 4X 8/32” x 3/8” Pan Head Bolts. 5 Repeat step 4 for 2 more vertical supports.
Frame Assembly for Granite Top Parts Needed. 1 Undo Stainless Steel Top by removing 6 x Pan head 8/32” x 3/8” bolts 3 Attach Granite corner top with 6 x #6 x 5/8” Pan Head wood screws into Outdoor plywood granite backer. Pan Head Screw (#6 x 5/8” Wood Screws) 2 4 Attach 2 included Granite rails using 4 x 8/32” x 3/8” pan head bolts at top of supports. Add silicone using 8 small dabs to hold top in place. Wipe up any extra silicone that seeps out during installation.
Levelling the Legs Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Foot Wrench 2 Rotate wrench to lower or raise corner of cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Fastening Cabinets 1 2 Parts Needed. Locate bolt slots on upright supports. 4 X Hex Nut (M5) 4 X Flat Washers (M5) X8 4 X Hex Bolt (M5 x 50mm) 3 Align hole locations , put bolt and washer through holes tighten nut lightly. 4 Level cabinets and tighten all bolts.
OUTDOOR KITCHEN 32"Bar Cabinet SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65003-INSTL-01-Rev.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 64" Worktop. Fits over 2 Cabinets 75 lbs. 88" Worktop. Fits over 2 Cabinets & Fridge nook. 32" - SS Bar Cabinet Max 350 lbs. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handles 3 2 Parts Needed. Tighten in bolts. Handle Bolts (M4 x 30mm) Align handle to holes on doors or drawers.
Installing the Legs 1 Parts Needed. 4 X Adjustable Feet 2 Open cabinet, remove any shelves or loose items. 4 X Adjustable Feet Flip cabinet upside down. Locate holes on crossbeam. 3 Align foot with holes on crossbeam. Tighten in Hex bolts . 3 4 1 2 4 Repeat step 3 for each corner. 5 Stand cabinet upright. To level and adjust legs go to next step.
Levelling the Legs Parts Needed. 1 X Wrench 2 3 Rotate wrench to lower or raise corner of cabinet. Repeat step 1-3 for each corner. 1 Use wrench to level cabinet and adjust height.
Installing the Casters(optional) 1 Parts Needed. 4 X Casters 2 Open cabinet, remove any shelves or loose items. 16 X Hex Washer Bolt Flip cabinet upside down, locate holes on crossbeam. 3 Align foot with holes on crossbeam. Tigh ten in Hex bolts. 3 4 1 2 4 Repeat step 3 for each corner. 5 Stand cabinet upright.
Installing the Drawer Inserting Drawer. Align Rails Slide In Removing Drawers.
Note: Fastening Cabinets 1 3 2 Parts Needed. 4 X Hex(M5) All drawers must be removed prior to fastening cabinets together. Remove plastic caps from cabinets. X8 4 X Hex Bolt (M5 x 50mm) Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Mounting the Worktop 1 Stand cabinet upright. 2 Place worktop over cabinets. 3 Insert the worktop bolt heads into the keyhole shape slots. 4 Push worktop in to lock. Tighten screws to secure top. Optional: Repeat steps 2-5 for mounting larger worktops.
Adjusting the Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
Wine Rack, Ice Tray and Garbage Bin Installation 1 Open Doors. Set rack clips in the desired slot locations on the upright posts. 2 Set rack on top of 4 clips at the same level height. Store beverage bottles. 3 Remove and install beverage chilling tray with formed metal edge. 4 Slide beverage chilling tray into/out of pullout frame. Push in frame to dock. 3 5 Remove and install Garbage bins 5 6 Slide Garbage bins into/out of pullout frame. Push in frame to dock.
OUTDOOR KITCHEN 32" Bar Cart SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65007-INSTL-01-Rev.
Weight Capacity 50 lbs. 30 lbs. 50 lbs. 100 lbs. Bar Cart Max 230 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handle 3 2 Parts Needed. Screw in bolts. Handle Bolt (M5 x 30mm) Align handle to holes on doors or drawers.
Installing the Casters Parts Needed. 4 X Casters 2 4 Flip cart upside down, locate holes on corner brackets. 3 Repeat step 2 for each corner. 16 X Hex Washer Bolt Align foot with holes on crossbeam. Screw in Hex bolts with washer and lock washer. Stand cart upright.
Installing the Drawers Inserting Drawers. Align Rails Slide In Removing Drawers.
Installing the Push Bar, Ice Tray, Liquor Rail 1 Parts Needed. Push handle should be attached by two locations 2 1 Ice Tray Push Bar 2X Pan Head 8mm Bolts 2 Tighten 2 x 8mm x 60mm bolts. In locations shown here. 3 4 Add Ice tray using handles to drop into to cutout in cart top 5 Add Liquor Rail by aligning bolt heads with keyhole slots in tray.
OUTDOOR KITCHEN 33"BBQ Cabinet SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65004-INSTL-01-Rev.
Weight Capacity 200 lbs. BBQ 115 lbs. 200 lbs. 33” - BBQ SS Max 515 lbs.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handle 3 2 Parts Needed. Screw in bolts. Handle Bolt M4 x 30mm Align handle to holes on doors or drawers.
Installing the Feet (Optional) 1 Parts Needed. 4 X Adjustable Feet Open cabinet, remove any loose items. 16 X Hex Bolt 2 Flip cabinet upside down, locate holes on crossbeam. 3 4 Repeat steps 2-3 for each corner. 5 Align foot with holes on crossbeam. Tighten in Hex bolts. Stand cabinet upright. To level and adjust legs go to next step.
Levelling the Legs Parts Needed. 1 X Wrench 2 3 Rotate wrench to lower or raise corner of cabinet. Repeat step 1-3 for each corner. 1 Use wrench to level cabinet and adjust height.
Installing the Casters ( Optional) Parts Needed. 4 X Casters 2 1 Open cabinet, remove any shelves or loose items. 3 Align caster with holes on crossbeam. Tighten in Hex bolts . 16 X Hex Washer Bolt Flip cabinet upside down on protected surface and locate holes on crossbeam. 3 4 1 2 4 Repeat step 3 to install all casters 5 Stand cabinet upright.
Note: Fastening Cabinets 1 3 2 Parts Needed. 4 X Hex (M5) All doors and drawers must be removed prior to fastening cabinets together. Remove plastic caps from cabinets. X8 4 X Hex Bolt (M5 x 50mm) Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Installing the BBQ 1 You may or may not need the adapter brackets depending on the model BBQ you choose 2 Place BBQ so that the rails touch the Brackets 3 Once the BBQ is centered on the Cart lift up edges of BBQ and Dab a little silicone on the rails to hold it in place 4 Place the propane tank in the ring of the tank tray. Rotate tank until bottom slot aligns with wingnut bolt. 5 Turn Wing nut bolt until it is seated in tank slot at bottom of tank. Parts Needed.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
OUTDOOR KITCHEN 32” Sink Base SS Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and shelves to avoid back injury. Do not leave children unattended near cabinets. For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com 65001-INSTL-01-Rev.
OTHER NOTES TO CONSUMER: Discoloration due to the high heat, for example beside a grill, is a trait of stainless steel and is not covered. Surface rust resulting from acid rain or environmental chemicals are not covered. (Please see maintenance information to combat surface rust). NewAge outdoor powder coated finishes are designed to withstand weathering and are UV stable.
Weight Capacity Worktops 32" Worktop. Fits over 1 Cabinet 200 lbs. 56 " Worktop. Fits over 1 Cabinet & Fridge nook. 75 lbs. 64" Worktop. Fits over 2 Cabinets 100 lbs. 32" - Sink Cabinet Max 375 lbs. 88" Worktop. Fits over 2 Cabinets & Fridge nook. 96" Worktop.
Unpacking • Begin by placing the package on a protected flat surface. • Remove all cardboard, foam packaging material and clear plastic bags. • Dispose / recycle all packaging materials. • Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.
Installing the Handles 1 Handle 3 2 Parts Needed. Screw in bolts. Handle Bolt M4 x 30mm Align handle to holes on doors or drawers.
Installing the Feet 1 Parts Needed. 4 X Adjustable Feet Open cabinet, remove any shelves or loose items. 16 X Hex Washer Bolt 2 Flip cabinet upside down, locate holes on crossbeam. 3 4 Repeat steps 2-3 for each corner. 5 Align foot with holes on crossbeam. Screw in Hex bolts with washer and lock washer. Stand cabinet upright. To level and adjust feet go to next step.
Levelling the Legs Parts Needed. 1 Use wrench to level cabinet and adjust height. 1 X Foot Wrench 2 Rotate wrench to lower or raise corner of cabinet. 3 Repeat step 1-3 for each corner. 4 Level Cabinet.
Inserting Cabinets Shelf 1 Open cabinet doors. Attach shelf clips to desired height. 2 Begin with shelf being level. 4 Lower shelf down onto shelf clips. 3 Insert and position over clips.
Fastening Cabinets 1 4 X Hex (M5) 3 2 Parts Needed. Remove plastic caps from cabinets. 4 X Hex Bolt (M5 x 50mm”) X8 Align bolts, tighten lightly. X4 4 Level cabinets and tighten all bolts.
Adjusting The Door Hinges Using a Philips screwdriver, the doors can be adjusted: Left, right, forwards and backwards. 1 To adjust the doors left or right, turn the screw (A) clockwise or counterclockwise. A 2 To adjust the gap between the doors and frame, turn the screw (B) clockwise or counterclockwise.
Plumbing Installation Locate the 3 pre slotted holes in the back of the cabinet. Using tin snips cut small webs to release the knockouts. Back View of Sink Cabinet. 1 Locate the 3 pre slotted holes in the bottom of the cabinet. Using tin snips cut small webs to release the knockouts. 2 3 Bottom View of Sink Cabinet. Connect the drain trap adapter to a p-trap and drainage tubing.