NEWCONT NEWCONT 2.4GHz CORDLESS CALLER ID TELEPHONE WITH CALL WAITING 40 CHANNEL AUTOSCAN NTP-6309 OWNER'S MANUAL INSTALLATION AND OPERATING INSTRUCTIONS NEWCONT PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE. Made in China 2002.8 NEWCONT 2.
Special Features C ongratulations on your selection of a quality NEWCONT product. With proper care and by following the setup and user instructions in this manual, this unit will provide you with years of trouble free service. NEWCONT is committed to providing quality products that fit your needs. We would like to have any comments or suggestions you might have on this product . You may mail your comments to: 40 Floor, Block C, Electronics science &Technology Bldg, Shennanzhonglu, Shenzhen , P.R.
Special Features Notes Luminous LCD Screen - The LCD Screen emits light for 8 seconds every time you press IMPORTANT any of the TELEPHONE KEYPAD buttons. In order to get maximum life from the HANDSET battery pack, be sure to charge the HANDSET for 12 hours before initial use. HANDSET Ringer Volume Level - Select the ringer volume level (HI, LOW, OFF). HANDSET Volume Control Switch - Select the receiver volume level(HI.MID,LOW).
HANDSET Controls Technical Information Technical Information This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could after operation of your system. 1. HANDSET ANTENNA Noise 2. NEW CALL/MESSAGE WAITING LED INDICATOR 9.BATT LOW INDICATOR LDCCF 3. LARGE LCD SCREEN CALLS BATT MSG DIR 10.SCROLL UP-DOWN/ SHIFT LEFT-RIGHT AM PM 4.
Problem Solving HANDSET Controls Problem Solving section 1.HANDSET ANTENNA For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. BASE UNIT is plugged into power source. 2. HANDSET is charged. 3. TONE/PULSE Select switch is in the right position. 4.TELEPHONE LINE CORD is plugged in the TELEPHONE JACK. 2. NEW CALL/MSG(MESSAGE )WAITING LED Indicator: Blinks when recording a new Range of phone limited, check the following: 1.
Changing the Battery Pack BASE UNIT CONTROLS Changing the BATTERY PACK The BATTERY PACK provides power for the HANDSET of your cordless telephone. 1. TELEPHONE LINE CONNECTION JACK pg.5,9,30 2. POWER-IN CONNECTION JACK pg.5 3. TONE/PULSE SELECT SWITCH pg.6.30 To Replace the BATTERY PACK: 1. Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it down. 2. Pull out the BATTERY CONNECTOR PLUG and remove the BATTERY PACK. 3. Plug the new BATTERY PACK into the BATTERY CONNECTOR. 4.
Recharging the Battery Pack BASE UNIT CONTROLS Battery Type 1. TELEPHONE LINE CONNECTION JACK Use the following type and size of BATTERY PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh 2. POWER-IN CONNECTION JACK NOTE: During a power interruption, the BASE UNIT does not operate, and a phone conversation cannot be made on the HANDSET. 3. TONE/PULSE Select Switch 4. ANTENNA: Raise or reposition for the best reception. 5.
FCC REGULATIONS This equipment complies with FCC REGULATIONS 15 and 68 of the Federal Communications Commission (FCC) rules for the United States. A label is located on the underside of the base unit containing the FCC registration number and Ringer Equivalence Number (REN) You must, upon request, provide this information to your local telephone company. This equipment is compatible with inductively coupled hearing aids.
Caller ID System Operation Contents TELEPHONE KEYPAD Characters Safety Instructions............................................................................................................3 The TELEPHONE KEYPAD Getting Started................................................................................................................. 5 button are used to enter characters when entering names. You can enter names in the UPPER CASE or LOWER CASE letters.
Caller ID System Operation Contents Saving in the Phone Book.............................................................................15 Preferred Calls.............................................................................................. .15 Blocked Calls................................................................................................15 Editing the Number in the Phone Book ......................................................... 16 I .
Caller ID System Operation 4. Use the dial pad to enter the three digit area code there your phone numbers begins with. 5. Press and hold down the 6. Press the SAVE /RE/PA button. / VOICE MAIL button to return to STANDBY mode. G. FLASH TIME This unit enables you to select the standard FLASH TIME applicable to your calling area. If you are not sure of the FLASH TIME you are using ,call your local telephone company. / VOICE MAIL button and hold down. 1.Press the 2.Press the TELEPHONE KEYPAD button. 3.
Safety Instructions E. If the telephone has been dropped or the case has been damaged. F. If the telephone exhibits a distinct change in performance. 16. Never install telephone wiring during a lighting storm. 17. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 18. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 19.
Caller ID System Operation Getting Started A. LANGUAGE Connecting Your Phone This telephone offers English, Spanish and French languages for your convenience. This section is a reference guide to the basic functions and operations of your cordless telephone. For more detailed descriptions of the operations and features of this telephone, refer to the Contents on page 1. 1. Carefully remove your cordless telephone from its shipping carton.
Getting Started Caller ID System Operation Function Operation BASE UNIT BASE UNIT ANTENNA TONE/PULSE SELECT SWITCH POWER-IN CONNECTION JACK This unit contains the following special functions: A. LANGUAGE F. AREA CODE TELEPHONE LINE CONNECTION JACK B. FIRST RING ON/OFF G. FLASH TIME C. TIME SET H. PAUSE TIME D. RINGER VOLUME I. VOICE MAIL E. LCD CONTRAST J.
Caller ID System Operation Getting Started Deleting All Records in the PHONE BOOK TALK 1. Press the DIR button to enter the phone book list. (If the phone book is not full, the LCD screen will disply "NEWDATA", press scroll UP or DOWN to enter the phone book list) 2. Press and hold down the DEL HANDSET /SCAN , the LCD screen will display "ERASE ALL" LDCCF Press the button to confirm that you have a dial tone. If you do not get a dial tone, review steps 3 through 12.
Cordless Telephone Operation Caller ID System Operation Preparing for Use Placing Calls from the PHONE BOOK Before you can use cordless telephone ,you must charge the HANDSET for 12 hours. Failure to do so will require recharging of the BATTERY PACK more often. (See page 26 for more information on the BATTERY PACK) 1. Press the DIR button. 2. Press the SCROLL UP 1. Place the HANDSET on the BASE UNIT for 12 hours . 2. After 12 hours ,remove the HANDSET from the BASE UNIT. 3.
Caller ID System Operation Cordless Telephone Operation Editing the Name and Number in the PHONE BOOK Placing Calls 1. press the 1. Press the button, the Call Timer starts to count. The HANDSET LCD Screen will display "CALLS " and "TALK ", and the BASE UNIT IN USE LED indicator will light up. button. DIR 2. Press the SCROLL UP EDIT button to find the record you want to edit. # TOTAL # 3. Press the or DOWN 2. Listen for a dial tone. /FLASH button to edit the name. 3. Dial the phone number.
Cordless Telephone Operation Caller ID System Operation Using the Headset Feature Speed Viewing the PHONE BOOK 1. Press the button. 2. Enter the first letter of a name. (See page 26 detail of entering a letter ). MICROPHONE 3. Press the SCROLL UP letter. button to find all names with the same first 4. Press the SCROLL DOWN Saving in the PHONE BOOK 1. Press the DIR button. The LCD screen will display "PHONE BOOK".
Caller ID System Operation Caller ID System Operation Caller ID System Deleting All Records in the Caller List This telephone automatically displays an incoming caller's name and telephone number together with the date and time of the call. It records up to 80 calls and stores the data in Memory. 1. Press and hold down the DEL /SCAN button while in the caller list, and display "ERASE ALL" 2. Press DEL /SCAN button again to delete all records, the display "NO CALL" AM # NEW TOTAL 3.
Caller ID System Operation Call Waiting When you subscribe to a Call Waiting service from your local telephone company, this telephone will display the name and number of the second caller while you are having a phone conversation with your first caller. 1. When you are having a conversation, this tele- e.g. phone will automatically display the name and number of the second caller. The name will be blinking. 2. Press the /FLASH button to answer the 1st caller second caller .The first caller's name.
