User's Guide
Table Of Contents
- Revision History
- Preface
- Chapter 1 Getting Started
- Chapter 2 EasySet
- Chapter 3 System Settings
- Introduction
- Programming Barcode/ Programming Command/Function
- Use of Programming Command
- Use of Programming Barcodes
- Illumination
- Aiming
- Good Read LED
- Power On Beep
- Good Read Beep
- Good Read Vibration
- Scan Mode
- Decode Session Timeout
- Image Stabilization Timeout (Sense Mode)
- Reread Timeout
- Image Decoding Timeout
- Sensitivity (Sense Mode)
- Scanning Preference
- Read Barcode On/Off
- Make a Beeping Sound
- Smart Stand Mode
- Decode Area
- Image Flipping
- Bad Read Message
- Power Off/Battery Off
- Default Settings
- Query Scanner Information
- Query Cradle Information
- Query Remaining Battery of Scanner
- Chapter 4 Wireless Communications
- Chapter 5 RS-232 Interface
- Chapter 6 USB Interface
- Chapter 7 Symbologies
- Introduction
- Global Settings
- Code 128
- EAN-8
- EAN-13
- Restore Factory Defaults
- Enable/Disable EAN-13
- Transmit Check Character
- 2-Digit Add-On Code
- 5-Digit Add-On Code
- Add-On Code Required
- EAN-13 Beginning with 290 Add-On Code Required
- EAN-13 Beginning with 378/379 Add-On Code Required
- EAN-13 Beginning with 414/419 Add-On Code Required
- EAN-13 Beginning with 434/439 Add-On Code Required
- EAN-13 Beginning with 977 Add-On Code Required
- EAN-13 Beginning with 978 Add-On Code Required
- EAN-13 Beginning with 979 Add-On Code Required
- UPC-E
- UPC-A
- Coupon
- Interleaved 2 of 5
- Febraban
- ITF-14
- ITF-6
- Matrix 2 of 5
- Code 39
- Codabar
- Code 93
- China Post 25
- GS1-128 (UCC/EAN-128)
- GS1 Databar (RSS)
- GS1 Composite (EAN UCC Composite)
- Code 11
- ISBN
- ISSN
- Industrial 25
- Standard 25
- Plessey
- MSI-Plessey
- AIM 128
- ISBT 128
- Code 49
- Code 16K
- PDF417
- Micro PDF417
- QR Code
- Micro QR Code
- Aztec
- Data Matrix
- Maxicode
- Chinese Sensible Code
- GM Code
- Code One
- USPS Postnet
- USPS Intelligent Mail
- Royal Mail
- USPS Planet
- KIX Post
- Australian Postal
- Specific OCR-B
- Passport OCR
- Chapter 8 Data Formatter
- Chapter 9 Prefix & Suffix
- Chapter 10 Batch Programming
- Appendix
Enter Setup
** Exit Setup 112
Coupon GS1 Databar Output
If you scan coupons that have both UPC and GS1 Databar codes, you may wish to scan and output only the data from the
GS1 Databar code. Scan the GS1 Output On barcode below to scan and output only the GS1 Databar code data.
When GS1 Output Off is selected, coupons that have both UPC and GS1 Databar codes are transmitted depending on
your selection for the “UPC-A/EAN-13 with Extended Coupon Code” feature.
** GS1 Output Off
GS1 Output On
When using the UPC-A Coupon feature, please ensure that System Character or System Character &
Country Code is selected for the “Transmit UPC-A Preamble Character” feature.