User's Guide
Table Of Contents
- Revision History
- Preface
- Chapter 1 Getting Started
- Chapter 2 EasySet
- Chapter 3 System Settings
- Introduction
- Programming Barcode/ Programming Command/Function
- Use of Programming Command
- Use of Programming Barcodes
- Illumination
- Aiming
- Good Read LED
- Power On Beep
- Good Read Beep
- Good Read Vibration
- Scan Mode
- Decode Session Timeout
- Image Stabilization Timeout (Sense Mode)
- Reread Timeout
- Image Decoding Timeout
- Sensitivity (Sense Mode)
- Scanning Preference
- Read Barcode On/Off
- Make a Beeping Sound
- Smart Stand Mode
- Decode Area
- Image Flipping
- Bad Read Message
- Power Off/Battery Off
- Default Settings
- Query Scanner Information
- Query Cradle Information
- Query Remaining Battery of Scanner
- Chapter 4 Wireless Communications
- Chapter 5 RS-232 Interface
- Chapter 6 USB Interface
- Chapter 7 Symbologies
- Introduction
- Global Settings
- Code 128
- EAN-8
- EAN-13
- Restore Factory Defaults
- Enable/Disable EAN-13
- Transmit Check Character
- 2-Digit Add-On Code
- 5-Digit Add-On Code
- Add-On Code Required
- EAN-13 Beginning with 290 Add-On Code Required
- EAN-13 Beginning with 378/379 Add-On Code Required
- EAN-13 Beginning with 414/419 Add-On Code Required
- EAN-13 Beginning with 434/439 Add-On Code Required
- EAN-13 Beginning with 977 Add-On Code Required
- EAN-13 Beginning with 978 Add-On Code Required
- EAN-13 Beginning with 979 Add-On Code Required
- UPC-E
- UPC-A
- Coupon
- Interleaved 2 of 5
- Febraban
- ITF-14
- ITF-6
- Matrix 2 of 5
- Code 39
- Codabar
- Code 93
- China Post 25
- GS1-128 (UCC/EAN-128)
- GS1 Databar (RSS)
- GS1 Composite (EAN UCC Composite)
- Code 11
- ISBN
- ISSN
- Industrial 25
- Standard 25
- Plessey
- MSI-Plessey
- AIM 128
- ISBT 128
- Code 49
- Code 16K
- PDF417
- Micro PDF417
- QR Code
- Micro QR Code
- Aztec
- Data Matrix
- Maxicode
- Chinese Sensible Code
- GM Code
- Code One
- USPS Postnet
- USPS Intelligent Mail
- Royal Mail
- USPS Planet
- KIX Post
- Australian Postal
- Specific OCR-B
- Passport OCR
- Chapter 8 Data Formatter
- Chapter 9 Prefix & Suffix
- Chapter 10 Batch Programming
- Appendix
Enter Setup
141
** Exit Setup
Check Character Verification
A check character is optional for China Post 25 and can be added as the last character. It is a calculated value used to
verify the integrity of the data.
Disable: The scanner transmits China Post 25 barcodes as is.
Do Not Transmit Check Character After Verification: The scanner checks the integrity of all China Post 25
barcodes to verify that the data complies with the check character algorithm. Barcodes passing the check will be
transmitted except the last digit, whereas those failing it will not be transmitted.
Transmit Check Character After Verification: The scanner checks the integrity of all China Post 25 barcodes to
verify that the data complies with the check character algorithm. Barcodes passing the check will be transmitted,
whereas those failing it will not be transmitted.
** Disable
Do Not Transmit Check Character After Verification
Transmit Check Character After Verification
If the Do Not Transmit Check Character After Verification option is enabled, China Post 25 barcodes
with a length that is less than the configured minimum length after having the check character excluded
will not be decoded. (For example, when the Do Not Transmit Check Character After Verification
option is enabled and the minimum length is set to 4, China Post 25 barcodes with a total length of 4
characters including the check character cannot be read.)