User's Guide
Table Of Contents
- Revision History
- Preface
- Chapter 1 Getting Started
- Chapter 2 EasySet
- Chapter 3 System Settings
- Introduction
- Programming Barcode/ Programming Command/Function
- Use of Programming Command
- Use of Programming Barcodes
- Illumination
- Aiming
- Good Read LED
- Power On Beep
- Good Read Beep
- Good Read Vibration
- Scan Mode
- Decode Session Timeout
- Image Stabilization Timeout (Sense Mode)
- Reread Timeout
- Image Decoding Timeout
- Sensitivity (Sense Mode)
- Scanning Preference
- Read Barcode On/Off
- Make a Beeping Sound
- Smart Stand Mode
- Decode Area
- Image Flipping
- Bad Read Message
- Power Off/Battery Off
- Default Settings
- Query Scanner Information
- Query Cradle Information
- Query Remaining Battery of Scanner
- Chapter 4 Wireless Communications
- Chapter 5 RS-232 Interface
- Chapter 6 USB Interface
- Chapter 7 Symbologies
- Introduction
- Global Settings
- Code 128
- EAN-8
- EAN-13
- Restore Factory Defaults
- Enable/Disable EAN-13
- Transmit Check Character
- 2-Digit Add-On Code
- 5-Digit Add-On Code
- Add-On Code Required
- EAN-13 Beginning with 290 Add-On Code Required
- EAN-13 Beginning with 378/379 Add-On Code Required
- EAN-13 Beginning with 414/419 Add-On Code Required
- EAN-13 Beginning with 434/439 Add-On Code Required
- EAN-13 Beginning with 977 Add-On Code Required
- EAN-13 Beginning with 978 Add-On Code Required
- EAN-13 Beginning with 979 Add-On Code Required
- UPC-E
- UPC-A
- Coupon
- Interleaved 2 of 5
- Febraban
- ITF-14
- ITF-6
- Matrix 2 of 5
- Code 39
- Codabar
- Code 93
- China Post 25
- GS1-128 (UCC/EAN-128)
- GS1 Databar (RSS)
- GS1 Composite (EAN UCC Composite)
- Code 11
- ISBN
- ISSN
- Industrial 25
- Standard 25
- Plessey
- MSI-Plessey
- AIM 128
- ISBT 128
- Code 49
- Code 16K
- PDF417
- Micro PDF417
- QR Code
- Micro QR Code
- Aztec
- Data Matrix
- Maxicode
- Chinese Sensible Code
- GM Code
- Code One
- USPS Postnet
- USPS Intelligent Mail
- Royal Mail
- USPS Planet
- KIX Post
- Australian Postal
- Specific OCR-B
- Passport OCR
- Chapter 8 Data Formatter
- Chapter 9 Prefix & Suffix
- Chapter 10 Batch Programming
- Appendix
Enter Setup
** Exit Setup 160
Set Length Range for Plessey
The scanner can be configured to only decode Plessey barcodes with lengths that fall between (inclusive) the minimum
and maximum lengths. To accomplish it, you need to set the minimum and maximum lengths.
Set the Minimum Length (Default: 4)
Set the Maximum Length (Default: 48)
If minimum length is set to be greater than maximum length, the scanner only decodes Plessey barcodes
with either the minimum or maximum length. If minimum length is same as maximum length, only
Plessey barcodes with that length are to be decoded.
Set the scanner to decode Plessey barcodes containing between 8 and 12 characters:
1. Scan the Enter Setup barcode.
2. Scan the Set the Minimum Length barcode.
3. Scan the numeric barcode “8” from the “Digit Barcodes” section in Appendix.
4. Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix.
5. Scan the Set the Maximum Length barcode.
6. Scan the numeric barcodes “1” and “2” from the “Digit Barcodes” section in Appendix.
7. Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix.
8. Scan the Exit Setup barcode.