User's Guide
Table Of Contents
- Revision History
- Preface
- Chapter 1 Getting Started
- Chapter 2 EasySet
- Chapter 3 System Settings
- Introduction
- Programming Barcode/ Programming Command/Function
- Use of Programming Command
- Use of Programming Barcodes
- Illumination
- Aiming
- Good Read LED
- Power On Beep
- Good Read Beep
- Good Read Vibration
- Scan Mode
- Decode Session Timeout
- Image Stabilization Timeout (Sense Mode)
- Reread Timeout
- Image Decoding Timeout
- Sensitivity (Sense Mode)
- Scanning Preference
- Read Barcode On/Off
- Make a Beeping Sound
- Smart Stand Mode
- Decode Area
- Image Flipping
- Bad Read Message
- Power Off/Battery Off
- Default Settings
- Query Scanner Information
- Query Cradle Information
- Query Remaining Battery of Scanner
- Chapter 4 Wireless Communications
- Chapter 5 RS-232 Interface
- Chapter 6 USB Interface
- Chapter 7 Symbologies
- Introduction
- Global Settings
- Code 128
- EAN-8
- EAN-13
- Restore Factory Defaults
- Enable/Disable EAN-13
- Transmit Check Character
- 2-Digit Add-On Code
- 5-Digit Add-On Code
- Add-On Code Required
- EAN-13 Beginning with 290 Add-On Code Required
- EAN-13 Beginning with 378/379 Add-On Code Required
- EAN-13 Beginning with 414/419 Add-On Code Required
- EAN-13 Beginning with 434/439 Add-On Code Required
- EAN-13 Beginning with 977 Add-On Code Required
- EAN-13 Beginning with 978 Add-On Code Required
- EAN-13 Beginning with 979 Add-On Code Required
- UPC-E
- UPC-A
- Coupon
- Interleaved 2 of 5
- Febraban
- ITF-14
- ITF-6
- Matrix 2 of 5
- Code 39
- Codabar
- Code 93
- China Post 25
- GS1-128 (UCC/EAN-128)
- GS1 Databar (RSS)
- GS1 Composite (EAN UCC Composite)
- Code 11
- ISBN
- ISSN
- Industrial 25
- Standard 25
- Plessey
- MSI-Plessey
- AIM 128
- ISBT 128
- Code 49
- Code 16K
- PDF417
- Micro PDF417
- QR Code
- Micro QR Code
- Aztec
- Data Matrix
- Maxicode
- Chinese Sensible Code
- GM Code
- Code One
- USPS Postnet
- USPS Intelligent Mail
- Royal Mail
- USPS Planet
- KIX Post
- Australian Postal
- Specific OCR-B
- Passport OCR
- Chapter 8 Data Formatter
- Chapter 9 Prefix & Suffix
- Chapter 10 Batch Programming
- Appendix
Enter Setup
41
** Exit Setup
Bad Read Message
You may scan the appropriate barcode below to select whether or not to send a bad read message (user-programmable)
when a good read does not occur before trigger release, or the decode session timeout expires.
** Bad Read Message OFF
Bad Read Message ON
Set Bad Read Message
A bad read message can contain up to 7 characters (HEX values from 0x00 to 0xFF). To set a bad read message, scan the
Set Bad Read Message barcode, the numeric barcodes representing the hexadecimal values of desired character(s) and
the Save barcode. The default setting is “NG”.
Set Bad Read Message
Set the bad read message to “F” (HEX: 0x46):
1. Scan the Enter Setup barcode.
2. Scan the Set Bad Read Message barcode.
3. Scan the numeric barcodes “4” and “6” from the “Digit Barcodes” section in Appendix.
4. Scan the Save barcode from the “Save/Cancel Barcodes” section in Appendix.
5. Scan the Exit Setup barcode.