RS Plus Series V2.
Welcome to the world of NEWLINE. Thank you for choosing the NEWLINE RS series Interactive Touch Screen. Please use this document to get the most out of your screen. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Symbol Conventions Symbols are used in this document to indicate operations that need particular attention. The symbols are defined as follows: Provides additional information to supplement operation in the main text. Indicates a potentially hazardous situation that, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results. WARNING Indicates a hazard with risk that, if not avoided, could result in death or injury.
Safety Instruction For your safety, please read the following instruction before you use the product. Serious injury or property damage may be caused by improper operations. Do not try to repair the product on your own. WARNING Disconnect the product from the power supply immediately if major failures occur. Major failures include the following: ⚫ If smoke, a peculiar smell or an abnormal sound is discharged from the product. ⚫ No image or sound is displayed, or the image error occurs.
WARNING Do not put items on the top of the product. ⚫ Do not put items, such as a container for liquid (a vase, flowerpot, cosmetics or liquid medicine) on the top of the product. ⚫ If any water or liquid is spilled on the product, the product may short circuit cause fire or electric shock. ⚫ Do not walk on or hang any items on the product. Do not install the product in an improper place.
CAUTION ⚫ Do not install the product on carpet or cloth. ⚫ Do not use a cloth such as table cloth to cover the product. Keep the product away from the radio. The product complies with the international EMI standard to pervent radio interference. However, interference may still exists and causes noise in the radio. If noise occurs in the radio, try the following solutions. ⚫ Adjust the direction of the radio antenna to avoid the interference from the product. ⚫ Keep the radio away from the product.
CAUTION may be damaged.
1 Parts and Functions 1.
Rear View ⚫ 65 INCH： 75 INCH/86 INCH: 1 Remote Control Receiver 7 Speakers 2 Power On/Off 8 Power Supply Plug 3 Light Sensor 9 Power Switch 4 Front Plate Cover 10 Internal PC Port (OPS) 5 Front Ports 11 Rear Ports 8
6 Front Buttons 9
1.2 Ports CAUTION Front USB ports and rear USB 3.0/USB 2.0 ports switch connections based on signal sources. If the current signal source is reading the data from an external product connecting to the port, please switch the signal source after the data reading is complete. Otherwise, the data or product may be damaged. For USB consumption, USB 2.0 provides up to 500ma whereas USB 3.0 provides up to 900ma.
WARNING The voltage/current of the rear power output port is 5 V/2 A (maximum). Purchase the power code/AC adapter according to customer needs. Please do not connect any products with different power requirement. Otherwise it may cause the damage to products or fire.
12
⚫ Front Buttons Buttons Operations Functions Short press Power on/off ⚫ Steady red color : Display is in shut down mode ⚫ Steady white color : Display is on and working Home Short press Go to the home page Return Short press Return to the last menu/Exit Menu Short press Open the Settings menu Long press for more than 2 seconds Lock the screen Short press Decrease the sound volume Long press for more than 1 second Continously decrease the sound volume Short press Increase the sound
Buttons Operations Power On/Off Mute/Unmute Audio 0-9 Enter number Go to the Home Page Return to Previous/Exit Up/Down/Left/Right Confirm/OK Enter Whiteboard Mode Take a Screenshot Enable Sound Only Mode Freeze the Current Screen, Click Again to Exit Freeze Function Adjust the Sound Volume Adjust the Brightness Enter the Source Selection Page View Currently Running Applications Open the File Manager View all Pre-installed Applications Switch Source to Internal PC Switch Source to Display Port HDMI FRONT
Buttons Operations Open the Browser Application Toggle Display Backlight Mode Start/Exit the Screen Lock Function ⚫ Open the Menu (Short Press) ⚫ Screen Lock (Long Press for More than 2 Seconds) Open the System Settings 15
2 2.
Installation Direction 2.2 Installation Precautions Weight Loading Weight of the product: 161lb/ 73 kg (86INCH), 123lb/56 kg (75INCH), 99lb/ 45kg (65INCH) ⚫ When using a mobile stand, ensure that the weight of the product is less than the loading capacity of the mobile stand. ⚫ When using the wall-mount bracket, ensure that the wall can support the weight of the product. We recommend that the wall surface be reinforced and have a loading capacity 4 times of the weight of the product.
For any problem, please contact our support desk. Our company is not responsible for any damage or losses incurred by users if the users fails to follow the instructions. Ventilation Ensure adequate ventilation and/or an air conditioned environment. We recommend keeping certain distances from the side of the product to the wall or panels. Ventilation requirements are shown in following figure.
2.3 Installation The dimensions of the four bracket mounting holes on the back panel are VESA MISFcompliant (86INCH or 75INCH: 800 x 400 mm/31.50 x 15.75 in; 65INCH: 600 x 400 mm/23.62 x 15.75 in). Use metric M8 screws with a length of 10 mm to 15 mm (0.40 to 0.59 in) to secure the touch screen to the mountingsystem. Dimensions of the mounting holes on the back panel are shown on the following figure. Consult a professional installer to install the display product. 75INCH/86INCH: 65INCH： 2.
The internal PC does not support hot plugging. Therefore, you must insert or remove the internal PC when the display is powered off. Otherwise, the display or internal PC may be damaged. You will need to purchase the internal PC separately. Perform the following steps to install the internal PC. Step 1 Unscrew the M3 screws by hand to remove the internal PC shielding cover. Step 2 Push the internal PC into the internal PC port at the rear of the panel from right to left.
21
3 Turning On/Off 3.1 Power On Step 1 Plug the power supply into the power outlet fully and plug the power connector into the side of the product. Ensure the power supply is in the range of 100V to 240V with frequency at 50 Hz/60 Hz ± 5%. The power current must be grounded. The power outlet should be installed near the equipment and should be easily accessible. Step 2 Flip the power switch located on the side of the product to “On”.
75INCH/86INCH: 65INCH: Step 3 Press the power button on the front control panel or on the remote control. 3.2 Power Off Step 1 Press the power button on the front panel or the power button on the remote control. when an internal PC is equipped, the information will be displayed as shown in the following figure.
Step 2 Press the power button on the front panel or the power button control again, the power indicator will turn to red. on the remote Step 3 If you are not going to use the product for an extended period of time, we recommend you switch the power switch to “Off”. ⚫ If an internal PC is equipped, the internal PC and the screen are powered off simultaneously when you power off the display. ⚫ Do not forcibly disconnect the power supply of the display when the internal PC is on.
4 Operating the Touch Screen 4.
4.
Main Icon Icon Functions Switch to the internal PC source. Click “Screen Sharing” to enable the wireless screen sharing function. Note: By default, the “Screen sharing” icon is displayed after startup. When you click “Add” or “Gadget” icon, “Screen sharing” switches to the “Connection” icon. Click Connection to view the connected sources, including Built-in PC, HDMI 1, HDMI 2, DisplayPort, HDMI Front and VGA. Whiteboard takes you to the whiteboard function and screen annotation functions.
The functions of the side toolbar are as follows: Icon Functions Enter annotation mode, and click again to stop annotation and take a screenshot. Access whiteboard mode. Go to Home page. Return to the previous menu/Exit an app. Go to the internal PC source. Manage currently running applications. Slide up/down the currently running application or click “×” at the upper right corner to close the application.
Icon Functions Go to your favorite source. You can set favorite source in the “tool bar” submenu in the system settings. Status Bar and Settings The upper right corner of the home page displays three working status icons (including USB drive(s), Ethernet, and Wi-Fi), system setting shortcut and return to the start screen page. Icon Functions If USB drive is connected to the USB port, this icon will appear. If the product is connected to Ethernet, the icon will appear.
5 Add Shortcut 5.1 Add Shortcuts to Home Page Step 1 On Home page, click the shortcuts will be displayed. icon in the lower right corner. The interface for adding Step 2 Click the icons on top to switch the list between external signal sources, Windows software shortcuts and pre-installed gadgets. ⚫ Click to view signal sources in Connection. ⚫ Click to view the Windows software shortcuts that the Newline Assistant uploads to the embedded operating system.
⚫ Click to view all Gadget applications. Step 3 Add or delete applications on the tab. ⚫ In the list, click the icon to add it as a shortcut on the Home page. A check icon will appear at the upper right corner of the shortcut icons. Up to 5 shortcuts can be added. ⚫ Tap the icon with the check mark again. The check icon will disappear and the shortcut will be removed from the Home page.
5.2 Newline Assistant 5.2.1 Introduction The Newline Assistant is the tool used as a bridge between the embedded operating system and the Internal PC (OPS). It helps add Windows software shortcut to the Home Page, as well as to protect USB data when switching between sources. Therefore we strongly recommend users install the Newline Assistant after installing the internal PC. 5.2.2 Installation Step 1 Connect Internal PC correctly (See also "Error! Reference source not found.").
Step 2 Click to return to the Home Page. Click the icon and go to the shortcut setting. The page for adding application programs will be displayed. Step 3 At the shortcut setting page, click icon to view all the Windows software shortcuts added by the Newline Assistant in Step 1. By default, the Newline Assistant application is added on the tab. Step 4 Tap the icon and add the shortcut at the Home page. Tap again and remove it. Step 5 Return to Home page.
6 Quick Setting Menu Using two fingers to swipe up from the bottom of the screen, the Quick Settings menu will appear, as shown in the following figure.
Icon Functions Drag the slider to adjust the brightness. Drag the slider to adjust the volume. Click the icon to return to Home page. Click the icon to enter the settings page. Click the icon to turn on/off the Smart system Wi-Fi. Click the icon to mute/unmute. Click the icon to turn on/off the beep sound. Click the icon to enable sound only mode. In sound only mode, the screen LCD displays and LED backlight turns off, other functions are in normal operating condition.
Icon Functions Click the icon to turn on/off the left toolbar. Click the icon to turn on/off the right toolbar. Click the icon to turn on/off the screen freeze function.
7 More Information For More Information Please visit our website (www.newline-interactive.com) for detailed instruction manual. Contact Us for Support Please email us at support@newline-interactive.com. Our company is devoted to product innovation and technology enhancement. Therefore, we may change product specs and information without notice, Product pictures in the manual are for reference only, please refer to actual products.
