Installation Guide

Recommended Installation by a Professional Plumbing Contractor
Note: The use of petroleum base plumbers putty on our products will nullify the warranty. We recommend
the use of clear silicone sealing materials. Recommended deck hole Ø1.25.
1. Place flange NUT (1) and WASHER (2) on valve BODY (3). Insert BODY (3), (blue cold & red hot), through hole in
the mounting surface. Adjust and secure with additional WASHER (2) and flange NUT (1) so that the top of valve stem
is 2" above top of mounting surface. Before tightening down flange NUT (1), check HANDLE (16) alignment by plac-
ing onto valve stem. Any adjustments for rotational alignment must be made to the valve BODY (3), not to the car-
tridge. See Figure 1.
2. Place the SPOUT (4) HOSES (5) and STUD (6) through base RING (7) and the center hole of mounting surface.
Secure SPOUT (4) into place with rubber GASKET (8), mounting CRESENT (9) and NUT(10), (align (8) and (9) slot
in direction of pop-up rod). See Figure 2.
3. Connect end of flexible HOSES (5) to side outlet of each valve BODY (3). (Hand-tighten and secure each connection
with a wrench ¼ turn.) See Figure 3.
4. Connect hot/cold water supply to appropriate 1/2” NPSM valve BODY (3), utilizing one of the three following types of
risers. Supply risers not included. See Figure 3.
a. 1/2” IPS flexible riser
: discard rubber nosecone WASHER (11), friction WASHER (12) and coupling NUT (13).
b. 3/8” or 1/2” OD bullnose riser: utilize friction WASHER (12) and coupling NUT (13).
c. 1/2” copper riser
:
utilize rubber nosecone WASHER (11), friction WASHER (12) and coupling NUT (13).
5. Place ESCUTCHEON (14), BONNET (15) and HANDLE (16) over cartridge. Any adjustments for rotational align-
ment must be made to the valve BODY (3) - not to the cartridge. (Note: Allow minimum spacing between HANDLE
(16) and BONNET (15) to prevent damage to the surface finish.) Secure HANDLE (16) into place with SCREW (17).
Press BUTTON (18) on HANDLE (16). See Figure 4.
6. Remove drain PLUG (19) from FLANGE (20). Place FLANGE (20) and white WASHER (21) through sink drain open-
ing. (Clear silicone may be used in place of white washer.) From bottom side of sink, place cone shaped rubber WASH-
ER (22) onto FLANGE (20) and slide up against sink bottom. Note: Cone portion of WASHER (22) to face upward.
Next slide on clear flat WASHER (23) and secure with flange NUT (24). Place clear WASHER (25) into drain BODY
(26) & tighten to FLANGE (20). Apply thread sealant to TAILPIECE (27) and attach to drain BODY (26). Attach TAIL-
PIECE (27) to p-trap drain (not included). See Figure 5.
7. Place drain PLUG (19) into FLANGE (20). Insert pop-up ROD (28) through spout and secure to STRAP (29), approx-
imately 1" from end of ROD (28), with SCREW (30). Insert ball ROD (31) into the drain's rod opening, secure with ball
rod NUT (32). Adjust the rise of the plunger and CLIP (33) into place. Adjust ball ROD (31) and pop-up ROD (28) so
drain will open and close properly. See Figure 6.
8. Remove AERATOR (34) from SPOUT (4), turn on water supply, and flush both valves until water is clear. Check for
leaks and make any final adjustments required. Re-attach AERATOR (34) to the SPOUT(4).
NWP-1760