Specification Sheet

t: 949.417.5207 l www.newportbrass.com
©2019 Brasstech, Inc.
Water Dispener Faucet
Features
• Solid brass construction
• Quarter-turn washerless ceramic disc valve cartridge
• ADA compliant contemporary cold lever handle
• Spout assembly with integral supply hoses
• 6-1/4” (15.9 cm) spout height at outlet
• 4” (10.2 cm) spout reach (c-c)
• For single hole configurations
• 1 gallon (3.6 liters) per minute maximum flow rate*
Codes / Standards Compliance
Meets or exceeds the following at date of manufacture:
• ASME A112.18.1/CSA B125.1
• IAPMO/cUPC
• NSF 61
• ADA (Handle Only)
• Energy Policy Act of 1992
• All applicable US Federal and State material regulations
Colors / Finishes
• 10B: Oil Rubbed Bronze
• 15: Polished Nickel
• 15S: Satin Nickel - PVD
• 26: Polished Chrome
• Other: Refer to the Newport Brass
catalog for additional color/finish options.
3180-5623
SEAGER
15S
10B 26 Other15
Specied Model
Model Description Colors | Finishes
3180-5623 Cold Water Dispenser Faucet
20-281 Integrated Air Gap Base **
Page 1 of 2 Spec_3180-5623
Product Specication Add “Color / Finish” sufx to Model number, below.
The Cold Water Dispenser Faucet shall be made of solid brass construction. Faucet shall incorporate a spout assembly with integral
supply hoses and feature a quarter-turn washerless ceramic disc valve cartridge. Faucet shall incorporate an ADA compliant transional
cold lever handle design. Cold Water Dispenser Faucet shall have a 1 gallon (3.6 liters) per minute maximum flow rate and accommodate
single hole configurations. Product shall incorporate a 6-1/4” (15.9 cm) spout height at outlet and a 4” (10.2 cm) spout reach (c-c). Cold
Water Dispenser Faucet shall be Newport Brass Model 3180-5623/____ . [Integrated Air Gap Base shall be Newport Brass Model 20-
281/____].
page 1 of 2 spec_
Product Specication:
Add "Color / Finish" sufx to Model number, below.
Features
• Solid brass construction
• Brass valve bodies
• Quarter-turn washerless ceramic disc valve cartridges
• ADA compliant traditional cross handles
• Spout assembly with integral supply hoses
• Pop-up drain with tailpiece
• 1-7/16" (3.7 cm) spout height at outlet
• 5-5/8" (14.3 cm) spout reach (c-c)
• For 8" (20.3 cm) centers - Maximum 20" (50.8 cm)
• 1.5 gallons (5.7 liters) per minute maximum flow rate
Codes / Standards Compliance
Meets or exceeds the following at date of manufacture:
• ASME A112.18.1/CSA B125.1
• IAPMO/cUPC
• IPC
• NSF 61
• ADA
• ICC/ANSI A117.1
• Energy Policy Act of 1992
• All applicable US Federal and State material regulations
• EPA WaterSense
®
Colors / Finishes
• 10B: Oil Rubbed Bronze
• 15: Polished Nickel
• 15S: Satin Nickel
• 26: Polished Chrome
• Other: Refer to the Newport Brass catalog for
additional color/nish options.
Specied Model
Model Description Colors / Finishes
920 Widespread Lavatory Faucet
10B 15 15S 26 Other
©2012 Brasstech, Inc.
t: 949.417.5207 | www.newportbrass.com920_rev-a
920
ASTOR
The two-handle Widespread Lavatory Faucet shall be made of solid brass construction. Faucet shall incorporate a spout assembly with
integral supply hoses and feature brass valve bodies with quarter-turn washerless ceramic disc valve cartridges. Faucet shall have a
1.5 gallon (5.7 liter) per minute maximum flow rate. Product shall be for 8" (20.3 cm) centers - Maximum 20" (50.8 cm). Product shall
incorporate a 1-7/16" (3.7 cm) spout height at outlet and a 5-5/8" (14.3 cm) spout reach (c-c). Faucet shall include a pop-up drain with
tailpiece and incorporate ADA compliant traditional cross handles. Widespread Lavatory Faucet shall be Newport Brass Model 920/____ .
Widespread Lavatory Faucet
*A Water Dispenser flow rate of approximately 1 gpm or less is
typical but will vary depending on installation specific factors
including in-line water pressure and water filtration system.
** The use of an air gap is required for dispenser faucets drawing from a reverse osmosis filtration system. The Integrated Air Gap Base
(20-281) affords the functionality of a separate air gap within the design of the product as depicted. Failure to specify the Integrated Air Gap
Base (20-281) will result in a product constructed using the standard base (no internal air gap).