Instructions / Assembly

HYDROSEAT
®
INSTALLATION INSTRUCTIONS
WARNING
DO NOT overtighten nuts or
tank/bowl may crack.
DO NOT USE PLUMBER’S PUTTY
TOOLS NEEDED:
• Pliers or adjustable wrench
• Screw driver or screw gun
• Putty knife
• Wax ring (depending on the depth of your flange)
• Bucket, sponge, paper towels
• Old towel or rug
21
543
876
Shut off the water to the tank and disconnect the supply line
from tank. Flush toilet and hold tank lever down to drain water
from tank. Sponge out water from tank and bowl.
Remove decorative caps that are covering the bolts, and set
aside for later use. Loosen and remove nuts and washers that
are holding toilet in place.
WARNING: TOILETS ARE HEAVY!
THIS MAY REQUIRE 2 PEOPLE
Remove bolts from floor flange and set aside. If floor flange
is damaged, replace. Use putty knife to scrape off wax and
residue from the floor flange. Wipe clean with paper towels.
If old bolts are being re-used to set toilet, wipe clean with
paper towel and re-install them in floor flange. If using new
bolts, place bolts in floor flange. Set wax ring onto floor flange,
making sure to center over pipe opening.
Note: Not compatible with the Perfect Seal product.
Remove toilet – you may need to gently rock the toilet to break
the seal. Lay down large towel or old rug and relocate toilet
onto the rug. CAREFULLY lay the toilet on its side or tilt toilet
and wipe off old, waxy residue from underside of toilet base
with paper towels.
Place Metal HydroSeat over the opening (with the BACK
towards the wall).
If the angled feet touch the floor without pressing down on the
wax, then a thicker or additional wax ring is needed.
Feet 3/8˝
above floor
If the angled metal feet are more than 3/8˝ above floor, then
remove the HydroSeat and use your hand to press down to
evenly flatten out the wax.
Replace the HydroSeat and recheck height until the feet are
about 3/8˝ above the floor.
Center bolts from the back wall. The bolts should be parallel
with the wall so that the toilet will be straight.
Note: Based on the flooring material, you may need to pre-drill
the screw holes or use alternative fasteners.
Screw HydroSeat down evenly, alternating sides, until screws
are snug, using included or other appropriate fasteners, based
on the floors surface.
WARNING: PLEASE MAKE SURE TO REMOVE
DEBRIS COVER BEFORE RESETTING TOILET
Line up bolts through the holes in base and reset the toilet.
Tighten nuts to secure toilet to the HydroSeat. Do not
overtighten. Reconnect water supply line (we recommend
replacing old, stiff supply line, with a new flexible supply line)
Turn on water and check supply line for leaks. Allow toilet to
fill. Flush to check for leaks.
Limited Warranty
This Next by Danco product is warranted to be free from defective materials and workmanship for the period of one (1) year after initial installation unless otherwise specified in writing. Defective units returned to Next by Danco
will be replaced without charge. This warranty applies only to the original purchase and installation of Next by Danco products.
Subject to the “Exclusions” set forth below, Next by Danco promises to the consumer to repair, or at the option of Next by Danco to replace any part of this plumbing product which proves to be defective in workmanship or
materials under normal use from the date of purchase. All costs of removal, transportation and reinstallation to obtain warranty service shall be paid by the consumer. During this Warranty, Next by Danco will provide subject to
the “Exclusions” section set forth below, all replacement parts free of charge, necessary to correct such defects.
EXCLUSIONS: THIS WARRANTY SHALL BE VOID IF THE PRODUCT HAS BEEN MOVED FROM ITS INITIAL PLACE OF INSTALLATION; IF IT IS HAS BEEN SUBJECTED TO FAULTY MAINTENANCE, ABUSE, MISUSE, ACCIDENT, OR OTHER
DAMAGES; IF IT WAS NOT INSTALLED IN ACCORDANCE WITH NEXT BY DANCO’S INSTRUCTIONS; OR IF IT HAS BEEN MODIFIED IN A MANNER INCONSISTENT WITH THE PRODUCT AS SHIPPED BY NEXT BY DANCO. NEXT BY DANCO
SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES CAUSED BY PRODUCTS THAT WERE NOT MANUFACTURED NEXT BY DANCO OR DAMAGES CAUSED BY IMPROPER INSTALLATION. NEXT BY DANCO’S OPTION TO REPAIR,
EXCHANGE, OR PROVIDE A REFUND FOR THE PRODUCT UNDER THIS WARRANTY DOES NOT COVER ANY LABOR OR OTHER COSTS OF REMOVAL OR INSTALLATION. NEXT BY DANCO SHALL NOT BE RESPONSIBLE FOR AND
DISCLAIMS ANY LIABILITY FOR SUCH COSTS OR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, NCLUDING WITHOUT LIMITATION COSTS OF INSTALLATION, WATER DAMAGE, PERSONAL INJURY, ATTRIBUTABLE TO
A PRODUCT DEFECT OR TO THE REPAIR, EXCHANGE, OR REFUND OF A DEFECTIVE PRODUCT, ALL OF WHICH ARE EXPRESSLY EXCLUDED FROM THIS WARRANTY. IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR
FITNESS FOR PURPOSE INTENDED ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. (SOME STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, SO THIS EXCLUSION
OR LIMITATION MAY NOT APPLY.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.
OPTIONAL/IF APPLICABLE
This warranty does not apply to local building code compliance. Since local code requirements vary greatly throughout the country, Distributors, Authorized Service Representatives, Dealers, Installation Contractors, and users
of plumbing products should determine whether there are any code restrictions applicable in any way to the product to insure local code compliance before installation. Next by Danco makes no representation or warranty
regarding, and shall not be responsible for, any code compliance
HS 10672 E/S 02/2015
Back
Wall
2727 Chemsearch Boulevard
Irving, Texas 75062
10672
Ph. [phone]
www.nextbydanco.com
© 2015 Danco, Inc. All Rights Reserved