Instructions / Assembly

2727 Chemsearch Boulevard
Irving, Texas 75062
HC660
Ph. [phone]
www.nextbydanco.com
© 2015 Danco, Inc. All Rights Reserved
VISIT OUR WEBSITE: WWW.NEXTBYDANCO.COM
to view an installation video, and get plumber’s tips,
frequently asked questions and trouble shooting advice.
Thumb Screw
Float Lock™
Refill Tube Port
Fill Valve Float
Upper Valve Body
Positive Locking
Mechanism
J-Tube Connection
Rubber Washer
Clip
Refill
Tube
Mini-Valve
®
Smart Nut
®
Sliding
Elbow
J-TubeFlexible tubing may need
to be cut to fit all tanks
Limited Warranty
This Next by Danco product is warranted to be free from defective
materials and workmanship for the period of one (1) year after
initial installation unless otherwise specified in writing. Defective
units returned to Next by Danco will be replaced without charge.
This warranty applies only to the original purchase and installation
of Next by Danco products.
Subject to the “Exclusions” set forth below, Next by Danco
promises to the consumer to repair, or at the option of Next
by Danco to replace any part of this plumbing product which
proves to be defective in workmanship or materials under
normal use from the date of purchase. All costs of removal,
transportation and reinstallation to obtain warranty service shall
be paid by the consumer. During this Warranty, Next by Danco
will provide subject to the “Exclusions” section set forth below,
all replacement parts free of charge, necessary to correct such
defects.
EXCLUSIONS: THIS WARRANTY SHALL BE VOID IF THE PRODUCT
HAS BEEN MOVED FROM ITS INITIAL PLACE OF INSTALLATION;
IF IT IS HAS BEEN SUBJECTED TO FAULTY MAINTENANCE,
ABUSE, MISUSE, ACCIDENT, OR OTHER DAMAGES; IF IT WAS
NOT INSTALLED IN ACCORDANCE WITH NEXT BY DANCO’S
INSTRUCTIONS; OR IF IT HAS BEEN MODIFIED IN A MANNER
INCONSISTENT WITH THE PRODUCT AS SHIPPED BY NEXT BY
DANCO. NEXT BY DANCO SHALL NOT BE RESPONSIBLE OR
LIABLE FOR ANY DAMAGES CAUSED BY PRODUCTS THAT WERE
NOT MANUFACTURED NEXT BY DANCO OR DAMAGES CAUSED
BY IMPROPER INSTALLATION.
NEXT BY DANCO’S OPTION TO REPAIR, EXCHANGE, OR PROVIDE
A REFUND FOR THE PRODUCT UNDER THIS WARRANTY DOES
NOT COVER ANY LABOR OR OTHER COSTS OF REMOVAL OR
INSTALLATION. NEXT BY DANCO SHALL NOT BE RESPONSIBLE
FOR AND DISCLAIMS ANY LIABILITY FOR SUCH COSTS OR
FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION COSTS OF INSTALLATION,
WATER DAMAGE, PERSONAL INJURY, ATTRIBUTABLE TO
A PRODUCT DEFECT OR TO THE REPAIR, EXCHANGE, OR
REFUND OF A DEFECTIVE PRODUCT, ALL OF WHICH ARE
EXPRESSLY EXCLUDED FROM THIS WARRANTY. IMPLIED
WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR
FITNESS FOR PURPOSE INTENDED ARE EXPRESSLY LIMITED
TO THE DURATION OF THIS WARRANTY. (SOME STATES OR
PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF IMPLIED WARRANTIES, SO THIS EXCLUSION OR LIMITATION
MAY NOT APPLY.)
DO NOT USE IN-TANK TOILET BOWL CLEANERS CONTAINING
BLEACH, CHLORINE, ALCOHOL OR OTHER ORGANIC SOLVENTS.
USE OF SUCH PRODUCTS WILL RESULT IN DAMAGE TO TANK
COMPONENTS AND MAY CAUSE FLOODING AND PROPERTY
DAMAGE. USE OF SUCH PRODUCTS WILL VOID THIS WARRANTY.
This warranty gives you specific legal rights. You may have other
statutory rights that vary from state to state or from province
to province, in which case this warranty does not affect such
statutory rights.
OPTIONAL/IF APPLICABLE
This warranty does not apply to local building code compliance.
Since local code requirements vary greatly throughout the
country, Distributors, Authorized Service Representatives, Dealers,
Installation Contractors, and users of plumbing products should
determine whether there are any code restrictions applicable in
any way to the product to insure local code compliance before
installation. Next by Danco makes no representation or warranty
regarding, and shall not be responsible for, any code compliance
There are no special skills required to install this product.
If water line or toilet appear to be leaking after installation,
you should call a plumber immediately.
NOTE: Save Instructions For Future Use
PLUMBER’S TIP:
To check for a leaky flapper, slide the
Float Lock to the off position after the tank
is full of water. Do not use the toilet for 1 hour.
After the hour, recheck the water level
inside the tank. If the water level has dropped,
there is a problem with the flapper’s seal.
PLUMBER’S TIP:
Whenever the main water supply to the building
is turned off, debris can get into faucets,
aerators and toilet fill valves when the water is
turned back on. To prevent this problem,
engage HydroClean’s patented Float Lock and
run the bath tub until the water is clear,
then disengage the Float Lock to fill the tank.
PLUMBER’S TIP:
Taking the time to adjust
the Mini-Valve for the
proper amount of water
added to the bowl can
make your toilet up to
30% more efficient
without effecting
flushing power.
WARNING
DO NOT USE IN-TANK DROP-IN TOILET
BOWL CLEANERS. Use of such products will
RESULT IN DAMAGE to tank components and MAY
CAUSE FLOODING and PROPERTY DAMAGE and
VOID WARRANTY.
DO NOT over tighten nuts or tank/bowl may crack.
Flapper Installation
OFF
OR
OR
ON
If you have installed the HydroClean fill valve,
there’s no need to turn off the water at the supply.
Simply, engage the Float Lock and flush the toilet.
Mounting Arms
Cut collar for plastic flush valve DO NOT cut collar for brass flush valve
Disengage the
Float Lock
OR
54321
109876
Shut water off, flush toilet to empty tank
and remove old flush valve.
Remove the Smart Nut at the bottom of the valve. Familiarize
yourself with the Positive Lock Mechanism and not how it
locks the valve into position. The click means the valve is
unlocked and the height can now be adjusted. No need to
adjust Valve height now. HydroClean adjusts after installation.
Tank sizes vary; lay J-tube along back of bottom of
tank, with Sliding Elbow in back right-hand corner,
as shown. Place Valve in tank to estimate J-tube
length needed.
Before attaching J-tube, adjust length by pulling
J-tube through Sliding Elbow if needed. For small
tanks, trim connection end carefully to fit. Push
J-tube onto bottom part of valve.
Position valve inside of tank making sure the
Rubber Washer is seated as shown.
Our Smart Nut should only be hand tightened
and should make 1-3 audible clicks to signal
it is tight. Wings are designed to bend if the nut
is overtightened, preventing leaks and cracking.
Lightly bump tab while turning the upper valve
body clockwise 1/4 turn. Then adjust the valve
up or down to the proper height.
Adjust the valve height so that the top of the cap is
even with the top of the tank. This height should
allow the final float adjustment to be achieved with
the Thumb Screw. Lock Valve into place by turning
Upper Body counterclockwise.
If the Overflow Tube has a cap, remove it and
discard before installing the bowl Refill Tube.
To install Refill Tube, attach Clip to top of Overflow
Tube. Trim Refill Tube to length to prevent kinking
and connect to Refill Tube Port.
151413
12
11
NOTE: Refill Tube must be positioned above the
overflow tube. DO NOT INSERT REFILL TUBE
DOWN THE OVERFLOW PIPE. This improper
installation violates the plumbing code and
could result in a leak.
If the building’s water supply was turned off, make
sure the Float Lock is engaged before attaching the
water supply to the tank.
DO NOT OVERTIGHTEN. We recommend replacing
an old, rigid metal water supply line with a flexible,
braided supply line.
DO NOT USE PLUMBER’S PUTTY TO SEAL FITTINGS.
Turn on the water and run the bath tub water to
flush out and debris. When water is clear, disengage
Float Lock to fill tank.
If water was turned off at the toilet, disengage the
Float Lock and turn the on water supply to fill the
tank. Use the Thumb Screw to adjust the proper
water level inside the tank as indicated on the tank
or 1/2˝ to 1˝ below the Overflow Tube.
Positive Locking
Mechanism
Smart Nut
Attach Refill Tube
to Refill Tube Port
Cap
Top Of Tank
Overflow
Tube
1˝ min
The C.L.
Line must
be at least
1˝ above
the top of
the overflow
tube.
Engage Float Lock
to turn off water to the valve
Clip to top of
Overflow Tube
Thumb
Screw
Float
Lock
Mini-Valve
Cone
Washer
Metal/Copper
Flared Tubing
Metal Flanged
Tubing
Flexible
Connector
RECOMMENDED
1817
16
Slowly add water to the bowl until level no longer
rises. Wait 2 minutes for the excess water to runoff
down the drain.
Use a pencil to mark 1/8˝ below the water level in
the bowl, then flush the toilet. If the valve is still
filling the bowl after the water reaches the pencil
mark, you will need to adjust the Mini-Valve to
decrease the amount of water filling the bowl.
HydroValve ships with the Mini-Valve at the midway
open position. Turn counterclockwise to decrease
the amount of water filling the bowl, adjusting up or
down until the tank shuts off close to the same time
as water in the bowl reaches the pencil mark.
Tank Bottom
Shank Washer
Valve Shank
Lightly bump tab
while turning the
Upper Valve Body
clockwise
HYDROCLEAN
®
INSTALLATION INSTRUCTIONS
HC 660 E/S 02/2015
3
22
1
4