Important Safety Instructions ， CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.
Important Safety Instructions NOTES 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a damp cloth. 7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Important Safety Instructions Warning Failure to avoid the following potentially hazardous situations may result in injury or property damage. The unit is designed to provide you with route suggestions. It does not reflect road closures or road conditions, traffic congestion, weather conditions, or other factors that may affect safety or timing while driving. Use the unit only as a navigational aid.
Important Safety Instructions Note: This equipment has been tested and found to comply with limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Accessories Accessories List ITEM NAME QTY Instruction Manual 2 AC Adaptor 1 Car Adaptor 1 Mounting Bracket 1 Mounting Cradle 1 Dashboard Mount Disk 1 USB Cable 1 Stylus 1 SD Card 1 Pouch 1 NOTE Accessories and their parts numbers are subject to modification without prior notice due to improvements.
Contents Important Safety Instructions …………………………………..………..1 Accessories ……………………………….…………...5 View of Main Unit ……………………………….…………...7 System Connections ……………………………….……….…..8 Power Supply Preparation …………………………….……….….….10 General Setup ……………………………….…………..12 Playing Music …………………………….……………..16 Photo Viewer ……………………………….…………..18 Use of the Mount Accessories ……………………………….…………..20 Troubleshooting ……………………………….…………..21 Specifications ……………………………….…………..
View of Main Unit 1. POWER Button Press for a longer time to enter or exit the standby mode. 2. Card Slot Insert the SD card into the slot. 3. Earphone Jack Used to connect earphones for private listening. When the earphones are connected to this jack, the speaker will be turned off automatically. 4. DC 5V Input Jack Used to connect to the supplied adaptor. 5. LCD Screen 6. USB Port Used to connect to the USB device. 7. RESET Button Press to reset the system.
System Connections z Always ensure that the unit and any other external device connected to the unit are switched off and unplugged from the power supply before you attempt to connect the unit to any external device. Connecting to PC The unit is designed with a USB port which allows you to connect the unit to a PC for map updating.
System Connections Inserting SD Card The unit is designed with an SD Card slot which allows you to insert the SD card into the unit as shown below: To remove the card, gently press the card in with your fingernail. The card unlocks and protrudes slightly. You can now remove the card. Connecting to Earphones Connect the earphones to the right side of the unit for private listening. When earphone is connected, the speakers will automatically turn off. Note: Overly loud volume could damage your hearing.
Power Supply Preparation Using the AC Adaptor The unit is supplied with an AC adaptor for powering and charging its battery. 1. Connect AC adaptor to the right side of the unit in the jack marked DC 5V IN, as shown on the right. Plug the two-prong end of the power cord into a grounded electrical outlet. 2. Note: ¾ ¾ Turn unit's power off before unplugging. When using the adaptor, the LCD screen will be brighter than with the rechargeable battery.
Power Supply Preparation Working conditions and precautions for the rechargeable battery ¾ ¾ ¾ Battery should only be used and charged when temperatures are between 32°-100°F. Maintain well-ventilated conditions around the product to avoid overheating. Don’t put the product on a bed, sofa or anything that may block ventilation to the product. When the battery is weak, an indication menu will appear on the LCD screen and the unit will power off automatically after a while.
General Setup System Main Menu When in navigation mode, tap button in the Menu screen. A confirmation message appears asking if you want to exit the program now, as shown below. In the confirmation screen, tap and the system main menu appears. In the main menu, there are four items for selecting. Touch the corresponding item to enter. Tap to enter navigation mode; tap to enter the MP3 Player; tap to enter to enter the setting menu.
General Setup Language Tap in the setting menu to enter Language setting menu for language selecting, as shown below: Tap the buttons to select language. Then tap D to confirm or tap U to cancel. Backlight Tap in the settings menu to enter Backlight setting menu for backlight adjusting, as shown below: Tap the first group buttons to adjust the backlight level. After setting, tap D to confirm or tap U to cancel.
General Setup Date & Time Tap in the settings menu to enter Date & Time setting menu for changing to the current time zone, as shown below: Tap the buttons to select the proper Time Zone. Tap the buttons of Date group to change the corresponding date and tap the buttons of Time group to change the corresponding time. Tap to return. Power Tap in the settings menu to enter Power menu for the current battery status, as shown below: The power menu will display the current battery status.
General Setup Calibrate Tap in the settings menu to calibrate, the screen will display as below: This item is used to calibrate the sensitivity of the touch screen. Tap the center of “+” as it moves around the screen. If you touch the center of “+” every time, it will disappear after having moved through a cycle (center→top left→bottom left→bottom right→top right). Tap the screen to return to the settings menu. Note: If “+” doesn’t disappear, you should calibrate again.
Playing Music The unit is designed with an SD card slot and supports MP3 and WMA format files playback. To use the MP3 player, you will need to have an SD card with your MP3 music files preloaded. Please note that you cannot use the navigation function of the device at the same time you are using the MP3 player. Remove the mapping software SD card that comes with the device from the SD card slot on the side of the unit. Then insert your SD card with your MP3 or WMA music files.
Playing Music In the screen, tap the MENU button to enter the MP3 play list menu, as shown below: When you open the play list, the system will look for audio files on its SD memory card and create a play list automatically. If the play list consists of more than one screen, tap the up arrow for the previous page and the down arrow for the next page. In the play list, double tap the songs to start playback. Tap ; when the button changes to orange, the player will repeat all the songs in the play list.
Photo Viewer The unit is designed with SD card slot and supports JPEG format files playback. To use the Photo Viewer, you will need to have an SD card with your JPEG picture files preloaded. Please note that you cannot use the navigation function of the device at the same time you are using the Photo Viewer. Remove the mapping software SD card that comes with the device from the SD card slot on the side of the unit. Then insert your SD card with your JPEG picture files.
Photo Viewer In the folder menu, double tap the memory card icon to open it, the pictures stored in the memory card will be listed on the screen. If the pictures list consists of more than one screen, tap the up arrow previous page and the down arrow for the next page. Tap menu. Tap a picture to select it and tap for the to return to previous to confirm your selection. In the pictures list, double tap a picture to play it on screen, as shown below.
Use of the Mount Accessories When using the unit in vehicle, you can use the supplied mount accessories (mount bracket, mount cradle and dashboard mount disk) to mount the unit in the vehicle. Take the following steps to operate: Fig. 1 1. Fig. 2 Fig. 3 See Fig. 1. Following the arrow, slide the mount cradle onto the mount bracket to fix it. 2. See Fig. 2. First, set the bottom edge of the unit onto the mount cradle.
Troubleshooting Take steps described in the tables below to solve simple problems before contacting customer service. If you suspect something wrong with this unit, immediately turn the power off and disconnect the power connector from the unit. Never try to repair the unit yourself because it is dangerous to do so. PROBLEM User can’t turn the unit on. There is no sound. Dark screen. The unit can’t receive satellite signals or can’t orient.
Troubleshooting PROBLEM The unit can receive signals now but can’t then or signals received are not stable. POSSIBLE CAUSE POSSIBLE SOLUTION The built-in rechargeable battery is weak. Use the adaptor to supply power or charge the battery. The unit may be obstructed by veil, such as heat insulation paper. Remove the veil. Swing of the unit is too great. Avoid great swing of the unit. System software of the unit fails to function after a change. Turn the unit on again.
Specifications TFT screen size 3.5 inches Frequency Response 20Hz - 20kHz Audio Signal-to-noise Rate ≥65dB Audio distortion+noise ≤-20dB (1kHz) Channel Separation ≥70dB (1kHz) Dynamic Range ≥80dB (1kHz) Power AC 100-240V - 50/60Hz; DC 5V Power Consumption < 8W Dimensions 103mmX77mmX23mm (L*W*D) Weight About 0.16kg Design and specifications are subject to change without notice. NextarTM, a trademark of Nextar (Hong Kong) Limited.
