Instruction Manual
INTRODUCTION TO USING YOUR BIKECAM The Nextbase range of cameras have been designed specifically with ease of use in mind, it is recommended NOT to change the default settings, which have been carefully selected to give the best performance for day to day use. Basic operation. The BikeCam is set to record video continuously, in files of just 3 minutes in length. There is no gap between each video file.
TABLE OF CONTENTS INTRODUCTION TO USING YOUR BIKECAM................................................................ 03 TABLE OF CONTENTS ................................................................................................. 04 PRECAUTIONS ............................................................................................................. 05 CAUTIONS ON USING THIS PRODUCT ...................................................................... 05 PRODUCT SPECIFICATION .....................
PRECAUTIONS Please read this manual carefully before operation and keep it for future reference. It will be helpful should you encounter any operational problem. CAUTION: To reduce the risk of electric shock, do not perform any servicing other than that contained in the instruction manual unless you are qualified to do so. Have the unit serviced by a qualified service technician if; The unit does not seem to operate normally. The unit exhibits a marked change in performance.
PRODUCT SPECIFICATION Model Number / Name NBDVR-RIDE / NEXTBASE RIDE BIKECAM Power Requirements 5V / 1.5A Power Supply 12-24Vdc power cable: Fuse Type: 20mm / 2A Output: 5Vdc Hard-wire cable: Fuse Type: 20mm / 2A Output: 5Vdc Sensor Resolution 14M Pixel (14,000,000 Pixel) Wide Angle Lens (front) Type / Angle / Aperture 6G / 110° / F2.0 Recording Resolution (Max.) 1920 x 1080 @ 30fps Screen Size 1.
PACKAGE CONTENTS Please check the contents of your BikeCam product. BikeCam Bar Mount Power Cable USB Cable Manuals & Software Disk Quick Start Guide Hard-wire Cable Quick Start Guide 1. Insert memory card Remove the waterproof cover and insert MicroSD card, 8-32Gb Class10. 3. Mounting Fit the bar mount and install the BikeCam. A) Release the U Bolt clamp, locate mount and re-tighten thumb screws.
PARTS & CONTROLS 10 9 5 1 2 3 8 USB RESET 6 7 4 1. BikeCam screen 2. BikeCam controls Mode / Power Mode: Press to change between video, photo or playback modes. Power: Press and hold for 2 seconds to turn on and off the BikeCam. Record / OK Record: Press to start or stop a recording when in video mode, or take a photo when in photo mode. OK: Press to confirm selection when in menus. Menu / File Protect Menu: Press to open the menu within current mode, press twice to open the general settings.
PARTS & CONTROLS (CONTD.) 10 9 5 1 2 3 8 USB RESET 6 7 4 3. LED indicators Blue = charging / Red = power on / Red flashing = recording 4. End cap Remove to gain access to the MicroSD slot, Micro USB 2.0 socket and RESET button. 5. Base plate Used to secure the BikeCam to the supplied Bar Mount, see page 15 for details. The base plate also has a threaded insert (1/4" UNC type) that can be used to mount the BikeCam with a variety of camera or professional RAM mounts, see page 16 for details. 6.
INSTALLATION Please read the information contained within this manual to ensure the installation of the BikeCam is carried out correctly and safely. 1. Insert memory card Remove the end cap from the rear of the BikeCam and insert a MicroSD card (8-32Gb Class10). Take care to ensure that the MicroSD card is the correct way round (gold contacts facing down). Push the memory card until it clicks into place.
INSTALLATION (CONTD.) 2. Power the BikeCam The BikeCam is supplied with two types of power cable, a standard 12Vdc power cable (cigarette plug) and a 12Vdc hard-wire cable. Both convert 12Vdc down to the required 5Vdc to operate your BikeCam correctly. Choose the preferred power cable to best suit your needs. Standard power cable: For use with a 12-24Vdc outlet typically found in vehicles and some motorbikes. 1 2 3 1.
INSTALLATION (CONTD.) Hard-wire power cable: For use when a 12-24Vdc outlet is not available, or when a permanent installation is required. 1 2 3 5 4 1. Waterproof connector for BikeCam Before connecting the power cable to the BikeCam, pull back the adaptor threaded housing to expose the Mini-USB connector and locating lug. Make sure these are both correctly aligned with the BikeCam sockets and then insert, re-locate the adaptor threaded housing and tighten, finger tight only. 2.
INSTALLATION (CONTD.) Hard-wire power cable installation: These instructions provide the necessary information to install the hard-wire cable properly and safely. Before beginning the installation process, please read these instructions carefully. The hard-wire cable has been supplied with ring terminals to allow quick and easy connection directly to the motorbikes battery. Planning for the 2.
BIKE INSTALLATION (CONTD.) Step 2: Connecting the hard-wire cable to the battery 2.1 Connect the positive (red) ring terminal to the positive (+) pole of the battery. 2.2 Connect the negative (black) ring terminal to the negative (-) battery pole or to the motorbike chassis to ground the hard-wire cable. Image for illustration purposes only. Warnings: - Protect yourself from an electric shock: When connecting the hard-wire kit to the battery, use a screwdriver or spanner with an insulated handle.
INSTALLATION (CONTD.) Mounting The BikeCam is supplied with a bar mount, this is designed to allow the quick and easy installation of the BikeCam without the need for any tools or technical knowledge. The BikeCam also has a threaded insert (1/4" UNC type) in the base plate, this can be used to mount the BikeCam with a variety of camera or professional RAM mounts that are readily available. Bar Mount: The bar mount is easy and quick to install, simply follow the instructions given below.
INSTALLATION (CONTD.) ® Advanced RAM mounting system: When using the BikeCam with a motorbike, it is recommended to use a professional RAM mounting system. The system is readily available to buy online, simply enter the given part numbers into your search engine. The base plate of the BikeCam has a threaded insert to attach the RAM fitting (PN: B-366U). Follow the instructions supplied with the RAM fittings to complete the installation to ensure the best results.
INSTALLATION (CONTD.) 5. Using the BikeCam Please see below for a guide to the basic operation of your BikeCam. Recording Indicator (flashing) Record On / Off Menu Battery LED Power LED On / Off button Press and hold for 2 seconds to turn the BikeCam on and off. Record / OK Button Press to start or stop a recording. Menu Press to open the Video menu, press twice to open the General Settings menu. Battery LED Indicates when the BikeCam is charging.
VIDEO MODE The information given below explains the various items that are displayed on the screen when your BikeCam is in Video mode, some items will only be displayed once the relevant function has been selected within the Video menu, as described below. 2 3 4 5 6 7 8 9 10 1 11 200MS 12 13 17 16 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 14 15 Time Lapse: displays the time lapse setting. WDR: remains on screen permanently as the BikeCam utilises WDR technology.
VIDEO MODE (CONTD.) Video settings menu The Video settings menu is accessed by pressing the MENU button whilst in Video mode. Use the UP and DOWN buttons to highlight setting and press the OK button to enter the options screen. Select the required option and press OK to confirm, press MENU again to return to video mode. Note: - Menus are not accessible during recording. Stop recording firstly to access the menu. 1.
VIDEO MODE (CONTD.) Video settings menu continued. 10. GPS Stamp Turn On / Off both the GPS co-ordinates and speed stamp that are shown on recorded files. When a recording is viewed using the Driving Recorder Player the GPS co-ordinates, speed information and map location remain available. Default Setting: On 11.
PHOTO MODE The information given below explains the various items that are displayed on the screen when your BikeCam is in Photo mode, some items will only be displayed once the relevant function has been selected within the Photo menu, as described below. 3 4 5 5M 2 6 7 8 9 ISO AUTO 2 M 10 1 1. Memory Card: indicates whether a memory card is present. 2. Quality: displays the current image quality. 3. WDR: remains on screen permanently as the BikeCam utilises WDR technology. 4.
PHOTO MODE (CONTD.) Photo settings menu The Photo settings menu is accessed by pressing the MENU button whilst in Photo mode. Use the UP and DOWN buttons to highlight setting and press the OK button to enter the options screen. Select the required option and press OK to confirm, press MENU again to return to photo mode. 1. Image Size Select image size, this will increase or decrease the size of the photographic image Default Setting: 8M 2. Colour Adjust the colour effect of the photographic image.
PLAYBACK MODE The information given below explains the various items that are displayed on the screen when your BikeCam is in Playback mode. Video Playback 1 2 15_0530_180233_006 3 1080P 4 30/05/15 18:02 5 6 OK: / II MODE: :PREV :NEXT 8 1. 2. 3. 4. 5. 6. 7. 8. 7 Video: indicates the BikeCam is displaying a video. Protected File: indicates that the video file is protected. File Number: displays current file number. Resolution: displays the resolution that current video was recorded in.
PLAYBACK MODE (CONTD.) The information given below explains the various items that are displayed on the screen when your BikeCam is in Playback mode. Photo Playback 1 2 15_0530_180233_006 3 3264 x 2448 4 30/05/15 18:02 5 6 7 1. 2. 3. 4. 5. 6. 7. Photo: indicates the BikeCam is displaying a photo. Protected File: indicates that the photo file is protected. File Number: displays current file number. Resolution: displays the resolution that current photo was recorded in.
GENERAL SETTINGS MENU The General settings menu is accessed by pressing the MENU button twice. Use the UP and DOWN buttons to highlight setting and press the OK button to enter the options screen. Select the required option and press OK to confirm, press MENU again to return to the original starting mode. 1. Wifi The Wi-Fi function allows you to view videos whilst recording, adjust the settings, control the basic functions (record, play, pause, etc.
GENERAL SETTINGS MENU (CONTD.) Continued from previous page. 10. Default Settings Reset the device to the default settings. 11. Auto Power Off Adjust the timing of the Auto Power Off function, this can be used to continue recording in event of loss of power within in the vehicle. Default Setting: 10 Seconds The default settings have been carefully selected to allow you to use the BikeCam without the need to change any settings.
FINALCAM (Wi-Fi) APP FOR ANDRIOD The Wi-Fi function allows you to use your smartphone to view videos during recording, adjust the BikeCam settings, control the basic functions (record, play, pause, etc.) and playback videos directly to your smartphone or tablet. The FinalCam App is available for free download from Google Play for Android smartphones.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Turn on the BikeCam Wi-Fi To turn on the Wi-Fi function on the BikeCam, go to the General Settings menu (press menu twice), select 'Wi-Fi' and press OK. The 'On' option will be highlighted, press the OK button to confirm. The menu window will close and the 'AP Mode' (Access Point Mode) window will open, as shown below. This screen gives the name of the BikeCam SSID (network name): 'RIDE******* and also the password: 12345678.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Connect your phone to the BikeCam To connect your phone to the BikeCam open the Wi-Fi connections menu on your phone, the BikeCam will be shown in Wi-Fi networks list as 'RIDE*******'. Tap on the 'RIDE******' and when prompted enter the password '12345678'. Once successfully connected the 'WiFi Connected' window will appear on the BikeCam screen, as shown below.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Using the FinalCam App Open the App by tapping on the FinalCam button on your phone, the first time the App is opened the 'Please click “+” to add camera' screen will appear, see image below. Pictures Settings Tap on the '+' button, select 'RIDE******' from the available networks, as shown below. Enter the password '12345678' and tap ‘Add’, the live video screen will appear. Press back on your smartphone to go to the FinalCam home screen, as shown on next page.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) The key below describes the various information, functions and features available within the FinalCam home screen. Pictures Settings 1. Camera name 2. Open camera Tap here to control the BikeCam. 3. Remove camera Tap here to remove the BikeCam from the FinalCam App. 4. Recordings Tap here to view the video files currently stored on the BikeCam's memory card.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Continued from previous page. 5. Camera Settings: Camera Name (SSID) – Change the SSID from the default setting of 'RIDE*******' and press the save icon. Password – Change the Password from the default setting of '12345678' and press the save icon. Note: - Changing the SSID or Password will disconnect the BikeCam from your phone, simply re-connect using the new details.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Continued from previous page. 6. FinalCam settings Storage Management Manage the storage capacity of files downloaded from the BikeCam to the Final Cam App. Language – Select language used within the FinalCam App. About – FinalCam version, with option to check whether there is an update available. 7. FinalCam home screen Tap here to return to the home screen from the FinalCam settings or Downloads screens. 8.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Basic operation Tap the 'Open camera' button on the home screen to start using the BikeCam. Please see below for a guide to the functions and features available when using the FinalCam App. Note: - Tap on the live image screen to bring up the menu selection as shown below. 1. FinalCam resolution Adjust the viewing resolution of the FinalCam App. Note: - Options available depend on the recording resolution setting of the BikeCam itself. 2.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Continued from previous page. 8. File List Tap to open the file list, this will list recordings or image that are stored on the memory card and have yet to be downloaded to your phone. 9. Camera Settings Tap here to open The Camera Settings menu (described earlier). 10. Volume Adjust the volume level of your phone. 11. Microphone This function is unavailable, as the BikeCam manages the microphone on or off settings. 12. Record Tap to start / stop recording. 13.
FINALCAM (Wi-Fi) APP FOR ANDRIOD (CONTD.) Playback of video files Once a recording has been downloaded from the BikeCam to you phone you can use the FinalCam App to playback the recording. 2 1 3 4 5 8 7 6 1. Filename The filename of the recording being viewed. 2. Back button Tap here to return to the previous screen / menu. 3. Favourites Tap to download the current file to the 'Favourites' folder within the File List directory. 4. Repeat Tap to toggle through the repeat options. 5.
FINALCAM (Wi-Fi) APP FOR iOS The Wi-Fi function allows you to use your smartphone to view videos during recording, adjust the BikeCam settings, control the basic functions (record, play, pause, etc.) and playback videos directly to your smartphone. The FinalCam App is available for free download from the App Store for Apple smartphones. Installing the App on an iOS smartphone: Open the App Store on your iOS smartphone and search for the 'FinalCam' App, tap on 'Get' to install.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Turn on the BikeCam Wi-Fi To turn on the Wi-Fi function on the BikeCam, go to the General Settings menu, select 'Wi-Fi' and press OK. The 'On' option will be highlighted, press the OK button to confirm. The menu window will close and the 'AP Mode' window will open, as shown below. This screen gives the name of the BikeCam SSID (network name): 'RIDE******* and also the password: 12345678.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Connect your phone to the BikeCam To connect your phone to the BikeCam open the Wi-Fi connections menu on your phone, the BikeCam will be shown in Wi-Fi networks list as 'RIDE*******'. Tap on the 'RIDE******' and when prompted enter the password '12345678', once successfully connected the 'WiFi Connected' window will appear on the BikeCam screen, as shown below.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Using the FinalCam App Open the App by tapping on the FinalCam button on your phone, the first time the App is opened the 'Please add a camera' screen will appear, see image below. Pictures Settings Tap on the '+' button, the 'Camera is connecting…' and then the 'Add device successful' screens will appear, as shown below. Pictures Pictures Settings Settings Enter the password '12345678' and tap ‘Add’, the live video screen will appear.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) The key below describes the various information, functions and features available within the FinalCam home screen. Pictures Settings 1. Camera name 2. Open camera Tap here to control the BikeCam. 3. Remove camera Tap here to remove the BikeCam from the FinalCam App. 4. Recordings Tap here to view the video files currently stored on the BikeCam's memory card.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Continued from previous page. 5. Camera Settings: Camera Name (SSID) – Change the SSID from the default setting of 'RIDE*******'. Password – Change the Password from the default setting of '12345678'. Note: - Changing the SSID or Password will disconnect the BikeCam from your phone, simply re-connect using the new details. - Using the 'Default Settings' option to return the BikeCam to the default settings will NOT reset the SSID or Password.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Continued from previous page. 6. FinalCam settings Storage Management Manage the storage capacity of files downloaded from the BikeCam to the Final Cam App. General – Turn on / off the 'Save to Album' option, when turned On images that are downloaded from the BikeCam will be saved in both the FinalCam directory and also your 'Camera Roll' album. Language – Select language used within the FinalCam App.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Basic operation Tap the 'Open camera' button on the home screen to start using the BikeCam. Please see below for a guide to the functions and features available when using the FinalCam App. Note: - Tap on the live image screen to bring up the menu selection as below. 1. FinalCam resolution Adjust the viewing resolution of the FinalCam App. Note: - Options available depend on the recording resolution setting of the BikeCam itself. 2.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Continued from previous page. 8. File List Tap to open the file list, this will list recordings or image that are stored on the memory card and have yet to be downloaded to your phone. 9. Camera Settings Tap here to open The Camera Settings menu (described earlier). 10. Volume Adjust the volume level of your phone. 11. Microphone This function is unavailable, as the BikeCam manages the microphone on or off settings. 12. Record Tap to start / stop recording. 13.
FINALCAM (Wi-Fi) APP FOR iOS (CONTD.) Playback of video files Once a recording has been downloaded from the BikeCam to you phone you can use the FinalCam App to playback the recording. 1. Back button Tap here to return to the previous screen / menu. 2. Favourites Tap to download the current file to the 'Favourites' folder within the File List directory. 3. Repeat Tap to toggle through the repeat options. 4. Delete Tap here to delete current file. 5. Volume Adjust the volume level of your phone. 6.
MASS STORAGE & PC CAMERA Use the supplied USB cable to connect the BikeCam to your PC, doing so will power on the camera with two functions available, as described below. Use the UP and DOWN buttons to select required function and press OK to confirm selection. - Mass Storage - PC Camera Using the BikeCam with a Windows PC: Mass Storage When Mass Storage is selected, the BikeCam screen will show the words ‘Mass Storage’ and then take the function of an SD Card reader for your PC.
DRIVING RECORDER PLAYER FOR WINDOWS This section will guide you through the installation of the Driving Recorder Player software, designed to enable the viewing of recorded files as well as checking journey route / GPS data (location and speed) and G Sensor information.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) INSTALLATION: Open the ‘NBDVR-RIDE Driving Recorder Player for Windows' folder and then open the folder with required version based upon your preferred speed units (MPH or KMH). Run the ‘setup.exe’, for some operating systems a security warning may appear, click ‘RUN’ to proceed. To install this application software you need to have 'Microsoft.NET Framework 4.0 Client' installed upon your PC.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) If your PC already had 'Microsoft.NET Framework 4.0 Client' installed then the 'Welcome to the InstallShield ….' window will open, as shown below. Press 'Next' to continue, the 'License Agreement' window will open, as shown below. Check the 'Accept' button and press 'Next' to proceed.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) The 'Destination Folder’ window will open, as shown below. Choose a destination folder should you not want files saved to the default folder within the Program Files directory. Press 'Next' to proceed, the 'Ready to Install the Program' window will open, as shown below. Click ‘Install’ to begin the installation.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) The 'Installing Driving Recorder Player' window will open. During installation the status window will be on screen, as shown below. Once installation is complete the 'InstallShield Wizard Completed' window will open, as shown below. Installation now is complete, press 'Finish' to close the InstallShield Wizard window. The Driving Recorder Player icon will now be available on your desktop.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) USING THE DRIVING RECORDER PLAYER: Connect the BikeCam to your PC using the supplied USB cable and select Mass Storage by pressing ‘OK’ on your BikeCam. Alternatively remove the MicroSD Card from your BikeCam and using a suitable MicroSD adaptor insert it directly to the card reader on your PC. Close any pop up messages and/or any media players which may automatically open when video or photo files stored upon a memory card are detected.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) FEATURES & CONTROLS The key below explains the various information displayed within the Driving Recorder Player when using a Windows platform. Map 1 16 2 15 N W 3 14 13 13/08/2013 14:08:44 NBDVR-RIDE AB12 3456 29MPH N 51 35 32.72 W 3 58 16.93 4 5 12 6 X: -0.03 Y: -1.06 Z: 0.16 - 7 8 9 10 11 1. Player settings File: Browse for files, change settings for units of speed and language. View: Open / close map window. Help: Player version information. 2.
DRIVING RECORDER PLAYER FOR WINDOWS (CONTD.) 10. Driving Recorder Player controls Screen Capture, this will create a still image for each frame of the image seen within the playback window. Open screen capture folder. Browse for files stored on your computer. Open settings window, adjust language and unit of speed. Open / Close the Map window. 11. Add / Remove files Used to add and remove selected videos to the file list. 12. File list Displays videos currently within the file list. 13.
DRIVING RECORDER PLAYER FOR MAC This section will guide you through the installation of the Driving Recorder Player software, designed to enable the viewing of recorded files as well as checking journey route / GPS data (location and speed) and G Sensor information. MINIMUM SYSTEM REQUIREMENTS: OS X 10.
DRIVING RECORDER PLAYER FOR MAC (CONTD.) INSTALLATION Open the 'NBDVR-RIDE Driving Recorder Player for Mac' folder and then open the folder with required version based upon your preferred speed units (MPH or KMH). Run the 'Driving Recorder Player for MAC' .dmg file, this will place the 'Driving Recorder Player' volume on your desktop, as shown below. Alternatively, once the required Driving Recorder Player software has been downloaded from the Nextbase website open the 'Downloads' folder on your Mac.
DRIVING RECORDER PLAYER FOR MAC (CONTD.) The Driving Recorder Player 'volume' can now be ejected, right-click, select Eject 'Driving Recorder Player” and right-click once more, see image below. The 'Driving Recorder Player' can also be found within the Applications List, see below. At this point may also want to drag a copy onto your desktop, this can then be used as a desktop shortcut or placed on your Dock.
DRIVING RECORDER PLAYER FOR MAC (CONTD.) USING THE DRIVING RECORDER PLAYER: Connect the BikeCam to your Mac using the supplied USB cable and select Mass Storage by pressing ‘OK’ on your BikeCam. Alternatively remove the MicroSD Card from your BikeCam and using a suitable MicroSD adaptor insert it directly to the card reader on your mac. Close any pop up messages and/or any media players which may automatically open when video or photo files stored upon a memory card are detected.
DRIVING RECORDER PLAYER FOR MAC (CONTD.) FEATURES & CONTROLS The key below explains the various information displayed within the Driving Recorder Player when using a Mac platform. Driving Recorder Player Version 1.0 14 1 13 ‘ ‘ 51 35 32.72 N 3 58 16.93 W 12 FILE LIST 11 2 13/08/2013 14:08:44 NBDVR-RIDE AB12 3456 29MPH N 51 35 32.72 W 3 58 16.93 10 3 4 5 FILE INFO Locked: Date: Location: No 2013-08-06 17:18:14 /Users/David/Desktop/402G - videos/17150019.MOV + ADD x REMOVE 6 7 8 9 1.
DRIVING RECORDER PLAYER FOR MAC (CONTD.) Driving Recorder Player Version 1.0 14 1 13 ‘ ‘ 51 35 32.72 N 3 58 16.93 W 12 FILE LIST 11 2 13/08/2013 14:08:44 NBDVR402G AB12 3456 29MPH N 51 35 32.72 W 3 58 16.93 10 3 4 5 FILE INFO Locked: Date: Location: No 2013-08-06 17:18:14 /Users/David/Desktop/402G - videos/17150019.MOV + ADD x REMOVE 6 7 8 9 10. Screen Capture Screen Capture, this will create a still image for each frame of image within the playback window.
TROUBLE SHOOTING PROBLEM SOLUTION Video Image is blurred. Remove the protective lens cover, clean the lens, clean the wind deflector screen! I can not insert the Micro SD card. Micro SD card are very small and require delicate use. Align the card with the diagram shown upon the device and insert the card until you feel a slight spring resistance. You now need to push the card, using your finger nail, until you hear and feel a small latch.
TROUBLE SHOOTING (CONTD.) PROBLEM SOLUTION No power to my BikeCam, but it works upon my PC. The cigarette power cable or hard-wire cable is not working. Inspect the fuse in the Car Power plug / hard-wire. Replacement fuse = 2A 20mm type. If the fuse is found to be blown, inspect the power cable for damage which may have caused the fuse blow. The SD card in my BikeCam can not be read. Use a good quality branded SD card between 4GB and 32GB and format the card from with in the SETUP menu of the BikeCam.
TROUBLE SHOOTING (CONTD.) PROBLEM The LCD screen on my BikeCam gets condensation inside. SOLUTION Not a serious issue. This is due to a combination of warm air inside the BikeCam and the cold air outside, especially whilst riding with the wind chill. Leaving the BikeCam indoors overnight with the SD card slot uncovered in a dry environment will reduce the moisture inside the BikeCam.
NOTES 65
NOTES 66
www.nextbase.co.
