User's Manual

Step 4
Place the Coverage Unit:
Move to a location in your home where you need to have improved
coverage. Plug the Coverage Unit into an easily accessible outlet. Wait
until the numeric display stops cycling. This could take several minutes.
At this point you should see a green icon indicating
that the unit is working properly. It is possible
to place the Coverage Unit so far away that it
cannot communicate with the Window Unit. If
this happens, a red icon will illuminate indicating
that you need to move the Coverage Unit closer
to the Window Unit.
TOO CLOSE
A zero on the numeric
display indicates that the
Coverage Unit needs to
be moved farther away
from the Window Unit.
GOOD
This green icon indicates
that the Coverage Unit
is functioning normally.
TOO FAR
This red icon indicates that
the Coverage Unit needs
to be moved closer to the
Window Unit.
Step 3
Optimize the Window Unit Placement:
The number of bars you can see on the Window Unit make a
signicant dierence in the operation of the Cel-Fi system. Try
moving the Window Unit to a couple of dierent spots to see if
you can get a better signal; the more bars the better.
Step 5
Optimize The Coverage Unit Placement:
The farther away you place the Coverage Unit from the Window Unit the better the
coverage in your home, so put the Coverage Unit as far away from the Window Unit
as possible. The number shown on the side of the display gives you an indication as to
the quality of the placement. Test two or three locations and for best results; try and get
an 8 or 9 on the display.
COVERAGE
UNIT
WINDOW
UNIT
COVERAGE
UNIT
WINDOW
UNIT
CEL
-
FIRS 2 Trouble Shooting
Indicator Issue Try This
Indicator Issue Try This
Indicator Issue Try This
Improving Performance Issue Try This
No lights on Window Unit display.
Status indicator is ashing green for
more than a minute.
Status indicator is on solid red.
No segment lit on signal display and
status indicator on solid green.
Center three bars on signal display are ashing.
No lights on Coverage Unit
display.
7 segment display is cycling
for more than a minute.
7 segment display shows a
value of 0.
Red “Too Far” Indicator.
Red Status Indicator.
E1
E3
E4
E8
The key to better performance is the placement
of the two units.
There is no power.
The Window Unit is attempting to
select a channel between the units.
Hardware Error.
Not receiving 3G signal.
Network operator data is missing.
There is no power.
The Coverage Unit is taking longer than
normal to make a link.
The Coverage Unit is “Too Close” to the
Window Unit.
The Coverage Unit is “Too Far” from the
Window Unit
Hardware Error.
No 3G signal on Window Unit.
Coverage Unit is overheating.
Window Unit is overheating.
Input signal too strong.
The Window and Coverage Units
are too close together (low coverage
number displayed), or the Window Unit
displayed signal level could be higher.
1. Is the unit plugged in?
2. Is there power at the outlet?
3. Try exchanging the power supplies with the Coverage Unit to see if the power
supply is defective.
1. Wait for the status indicator to stop ashing, this could take several minutes.
1. Try resetting the Window Unit by unplugging it and then plugging it back in.
2. If problem persists return system for service/replacement.
1. Try moving the Window Unit to another room or area where you have more
coverage. (Use your cell phone to nd the best 3G coverage).
1. Insert operator SD card into Window Unit.
1. Is the unit plugged in?
2. Is there power at the outlet?
3. Try exchanging the power supplies with the Window Unit to see if the power
supply is defective.
1. Wait for the display to stop cycling, this could take several minutes
2. Move away from WiFi or other wireless devices.
1. Move the Coverage Unit farther away from the Window Unit.
1. Move the Coverage Unit closer to the Window Unit.
1. Try resetting the Coverage Unit by unplugging it and then plugging it back in.
2. If problem persists return system for service.
Try moving the Window Unit to another room or area where you have coverage.
(Use your cell phone to nd the best 3G coverage).
Make sure that the vents on the unit are not blocked. Move the unit to a cooler area.
The system will start working normally when it cools down.
The signal from the wireless network is too strong to use a booster.
Move Coverage Unit further away from Window Unit to achieve a coverage unit
number of 8 or 9 (even placing the Coverage Unit at the opposite end of the house). A
higher number means better coverage. You can also improve performance by moving
the Window Unit to a location with higher signal. The more bars the better!
WINDOW
UNIT
COVERAGE
UNIT
ERROR
MESSAGES
PERFORMANCE
qsg-RS2.2-English_14-0226
+
((( )))
Signal
Indicators
Power & Status