User's Manual

ManualsBrandsNextivity ManualsElectronicsProvider-Specific Consumer Signal Booster

tion against harmful interference in a residential

installation. This equipment generates, uses and

can radiate radio frequency energy and, if not

installed and used in accordance with the instruc-

tions, may cause harmful interference to radio

communications. However, there is no guarantee

that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which

can be determined by turning the equipment off

and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equip-

ment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV

technician for help

ISED STATEMENT

BEFORE USE, meet all requirements set out in

CPC-2-1-05.

This device may operate in a xed location only, for

in-building use.

In order to comply with ISED RF Exposure

requirements, this device must be installed to

provide at least 20 cm separation from the human

body at all times.

An de se conformer aux exigences d’exposition

RF de ISED, cet appareil doit être installé pour

fournir au moins 20 cm de séparation du corps

humain en tout temps.

The Manufacturer’s rated output power of this

equipment is for single carrier operation. For

situations when multiple carrier signals are

present, the rating would have to be reduced by

3.5dB, especially where the output signal is re-

radiated and can cause interference to adjacent

band users. This power reduction is to be by

means of input power or gain reduction and not by

an attenuator at the output of the device.

[FRENCH: La puissance de sortie nominale

indiquée par le fabricant pour cet appareil concerne

son fonctionnement avec porteuse unique. Pour

des appareils avec porteuses multiples, on doit

réduire la valeur nominale de 3,5dB, surtout si le

signal de sortie est retransmis et qu’il peut causer

du brouillage aux utilisateurs de bandes adjacentes.

Une telle réduction doit porter sur la puissance

d’entrée ou sur le gain, et ne doit pas se faire au

moyen d’un atténuateur raccordé à la sortie du

dispositif.]

This device complies with Industry Canada license-

exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may

not cause interference, and (2) this device must

accept any interference, including interference that

may cause undesired operation of the device.

[FRENCH: Le présent appareil est conforme

aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes: (1)

l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.]

Gain 95dB (=<1GHz)

100dB (>1GHz)

Bandwidth 75Mhz

Input and Output

Impedances

50 ohm

Output

Power

Uplink 22dBm per band

Downlink 16dBm per band

Compliance Contact

In the event of regulatory compliance issue, please

contact Nextivity Inc. directly. Contact information

is available at www.nextivityinc.com.

Patents

This product is covered by Nextivity, Inc., US

patents and patents pending. Please refer to

cel-.com for details.

reserved. Reproduction or media conversion by

any means is protected by copyright and may only

occur with prior written permission of Nextivity.

legal_GO-X-Eng_17-0302 legal_GO-X-Eng_17-0302