Instruction Manual
4 5
TIMER SETTING
1. At standby mode, press and hold the TIMER button on the remote. The hour on the
display will begin blinking on the screen with the flashing timer icon “T”.
2. Press the TUNING/SKIP/SEARCH buttons on the remote to adjust the hour.
3. Press the TIMER button to confirm. The minute on the display will begin blinking.
4. Press the TUNING/SKIP/SEARCH buttons on the remote to adjust the minute.
5. Press the TIMER button on the remote to confirm your setting.
6. After the set time is reached, the unit will power on to the radio automatically.
7. The timer function can be deactivated or activated by short pressing the TIMER button on
the remote.
USB & SD/MMC CARD PLAYBACK
1. Power on the unit, insert an USB or a SD/MMC card into the unit.
2. Press MODE button repeatedly to switch to USB or card mode. The playback will start
automatically.
3. Press the TUNING SKIP/SEARCH FORWARD button on the remote to skip to the next
track; press and hold to search through the track forward.
4. Press the TUNING SKIP/SEARCH BACKWARD button on the remote to skip to the
previous track; press and hold to search through the track backward.
5. Use the numeric buttons to enter the track number to select your desired track for
playback.
BLUETOOTH OPERATING
This unit can receive stereo audio signal from a BLUETOOTH stereo audio source device.
1. Power on the unit, switch to BLUETOOTH mode by pressing MODE button repeatedly.
2. LED indicator rapid blinking while it is pairing.
3. Enable the Bluetooth of the Bluetooth audio source device.
4. Pair and connect to MIB668A(the unit) on the audio source device. If prompted for
passcode, enter “0000”.
5. Pairing successful (LED indicator blue), ready to stream music.
6. During playback, press PLAY/PAUSE button to cease or resume the playback.
7. During playback, press TUNING/SKIP/SEARCH FORWARD button to skip to the next
track; press TUNING/SKIP/SEARCH BACKWARD button twice to skip to the previous
track.
8. During playback, press and hold TUNING/SKIP/SEARCH buttons to search through the
current track forward or backward.
Note:
Pairing mode is canceled about 1.5 minutes.
The above are generic steps to pair a BLUETOOTH device, for more specific instructions
on BLUETOOTH connectivity for your device, please consult your manufacturer’s
manual.
RE-CONNECT TO THE BLUETOOTH AUDIO SOURCE DEVICE
If the device is already paired with the MIB668A, but became unconnected even with both
Bluetooth devices turned on. You can re-connect them by following steps:
1. Press and hold the PAIR button on the unit or on the remote to re-link the audio source
device. The Bluetooth indicator will blink for about 1.5 minutes for connecting.
2. Select MIB668A on the audio source device for connecting. Bluetooth indicator will turn to
solid blue if the MIB668A and the device have been re-connected successfully.
EQ EFFECTS
During playback, press EQ button on the remote repeatedly to cycle through the EQ options;
when your desired EQ effect shows on the screen, release the button.
FM RADIO
TUNING THE FM RADIO
1. Power on the unit, switch to FM (RADIO) mode by pressing MODE button repeatedly.
2. Press the TUNING/SKIP/SEARCH buttons on the remote to fine tune radio station. Press
and hold the TUNING/SKIP/SEARCH buttons on the remote to auto search radio station
forward or backward respectively (When an available station will be found, the unit will
broadcast it immediately and the searching will be stopped). During auto searching, press
the TUNING/SKIP/SEARCH buttons on the remote to stop the searching.
3. At radio mode, it is possible to access the frequency via numeric buttons on the remote
control. For example, press buttons 8, 9 and 8 to get to 89.8 MHz.
STORING YOUR FAVORITE RADIO STATION
1. During playback, press the MEM button on the remote for storing the current station until
a memory cell number flashes on the screen.
2. Use the CH+ or CH- buttons on the remote to select the corresponding memory cell for
storing the station.
3. Confirm your selection by pressing the MEM button on the remote.
4. During radio playback, press the CH+ or CH- buttons on the remote repeatedly to recall
the stored stations.
MUTE THE UNIT
During playback, press the MUTE button on the remote to switch off the audio. Press the
button again to resume the audio.
VOLUME LEVEL/TREBLE/BASS ADJUSTMENT
Press the VOLUME +/- buttons or TREBLE +/- buttons or BASS +/- buttons on the remote to
adjust the volume output level or treble effect or bass effect.
PROFESSIONAL AUDIO MODES
During playback, press the VOICE, MUSIC or MOVIE buttons on the remote to switch
among voice, music and movie audio modes for getting high sound quality. The audio
modes can reveal the characters and details of the sound of the voice, music and movie and
make you liked being there.