Installation Instructions
25 – English
TABLE C – Motor head led signals
GREEN LED Meaning
0 flashes
= at least 1 transmitter memorised and 2 limit positions
programmed.
1 flash
= at least 1 transmitter memorised and 1 limit position
programmed.
2 flashes
= at least 1 transmitter memorised and no limit posi-
tions programmed.
3 flashes
= no transmitter memorised (the limit switch status is
not shown by the led).
RED LED Meaning
0 flashes = no error.
steady on
= serious error - 1 (motor damaged - contact technical
service).
1 flash = thermal protection function in progress.
2 flashes
= the last movement was automatically interrupted by
The “Obstacle detection” function.
3 flashes = load too high relative to motor nameplate rating.
4 flashes = serious error - 2.
5 flashes = serious error - 3.
6 flashes = serious error - 4 (control circuit temperature too high).
7 flashes = serious error - 5 (brake malfunction).
8 flashes = serious error - 6 (brake malfunction).
9 flashes = serious error - 7.
10 flashes = serious error - 8.
11 flashes = serious error - 9.
The motor repeats the report message on the status of the installation by performing
some brief movements when a movement is commanded. To understand the signifi-
cance of these movements read Table D.
TABLE D – Movement signals
No. of MOVEMENTS Meaning
0 movements
= at least 1 transmitter memorised and 2 limit positions
programmed.
1 movement
= no transmitter memorised (the limit switch status is
not shown by the movements).
2 movements
= at least 1 transmitter memorised and at least 1 limit
position still to be programmed.
5 movements = serious motor memory error.
What to do if...
(troubleshooting guide)
In general, to better identify the problem, refer to Table C (and D), section 5.10.
q Powering an electrical phase, the motor does not move:
After excluding the possibility that thermal protection is active, in which case it is
sufficient to wait for the motor to cool down, make sure the mains voltage corre-
sponds to the values indicated in the “technical data” chapter of this manual by
measuring the voltage between the “common” wire and the electrical phase wire
supplied with current. If the problem is still present, disconnect the power cord
from the motor (fig. 3-i) and connect it again.
q When an Up command is sent, the motor does not start:
This can happen if the awning is near the Upper limit switch (“0”). In this case you
must lower the awning a little bit and give the Raise command again.
q The system operates in the emergency condition with an operator pre-
sent (hold-to-run):
– Check to see if the motor has undergone a significant electrical or mechanical
shock.
– Make sure each part of the motor is still in good condition.
– Delete the UP (“0”) and DOWN (“1”) limit position and reprogram them.
Disposal of the product
As in installation, also at the end of product lifetime, the disassembly and scrapping
operations must be performed by qualified personnel.
This product comprises various types of materials: some may be recycled others
must be disposed of. Seek information on the recycling and disposal systems envis-
aged by the local regulations in your area for this product category. Caution! – some
parts of the product may contain pollutant or hazardous substances which, if dis-
posed of into the environment, may cause serious damage to the environment or
physical health. As indicated by the symbol on the left, disposal of this product in
domestic waste is strictly prohibited. Separate the waste into categories
for disposal, according to the methods envisaged by current legislation in
your area, or return the product to the retailer when purchasing a new
version. Caution! – Local legislation may envisage serious fines in the
event of abusive disposal of this product.
The packing materials of the product must be disposed of in compliance with local
regulations.
Technical Characteristics
n Frequency 433.92 MHz n Power emitted: 0 dBm n Radio coding: “BD”.
Refer in any case to the data on the motor’s rating plate..
Note: • All technical specifications stated herein refer to an ambient temperature of
20° C (± 5° C). • Nice S.p.A. reserves the right to apply modifications to products
at any time when deemed necessary, maintaining the same intended use and func-
tionality.
EU DECLARATION OF CONFORMITY
Hereby, NICE S.p.A., declares that the radio equipment type E EDGE SI 332 AC BD,
E EDGE SI 620 AC BD, E EDGE SI 1012 AC BD, E EDGE MI 332 AC BD, E EDGE
MI 632 AC BD, E EDGE MI 1020 AC BD, is in compliance with Directive 2014/53/EU
The full text of the EU declaration of conformity is available at the following internet
address: http://www.niceforyou.com/it/supporto
COMPLIANCE WITH THE FCC RULES (PART 15) AND RSS-210 RULES
This device complies with Industry Canada’s licence-exempt RSS-210s, and with
Part 15 of the FCC rules of the United States of America. Operation is subject to the
following two conditions: (1) this device may not cause interference; (2) this device
must accept any interference, including interference that may cause undesired op-
eration of the device.
Any changes or modications made to this device, without the express permission of
the manufacturer, may void the user’s authority to operate this device.