Datasheet

ALUMINUM ELECTROLYTIC CAPACITORS
CL
Chip Type, Low Impedance
series
V
Code
6.3
j
10
A
16
C
25
E
35
V
50
H
Voltage
Chip type, low impedance, temperature range up to +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Type numbering system (Example : 16V 100µF)
U
1
C
2
L
3
1
4
C
5
1
6
0
7
1
8
M
9
C
10
L
11
1
12
G
13
S
14
Configuration
Size code
Taping code
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (16V)
Series name
Type
10 × 10
A
B
C
E
L
H
4 × 5.8
1.8
4.3
4.3
1.0
5.8
0.5 to 0.8
5 × 5.8
2.1
5.3
5.3
1.3
5.8
0.5 to 0.8
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 to 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 to 0.8
10 × 7.7
3.2
10.3
10.3
4.5
7.7
0.8 to 1.1
8 × 10
2.9
8.3
8.3
3.1
10
0.8 to 1.1
8 × 6.2
3.3
8.3
8.3
2.3
6.2
0.5 to 0.8
3.2
10.3
10.3
4.5
10
0.8 to 1.1
(mm)
10 × 13.5
3.2
10.3
10.3
4.5
13.5
0.8 to 1.1
φ D × L
A2 100C CL
(
φ4 to φ8 × 6.2
)
(
φ8 × 10L, φ10
)
Chip Type
0.3 MAX.
φD
±
0.5
B
±
0.2
A
±
0.2 A
±
0.2
C ± 0.2
0.5 MAX.
E
H
H
0.3 MAX.
φD
±
0.5
B
±
0.2
A
±
0.2 A
±
0.2
C ± 0.2
0.5 MAX.
E
L ± 0.3
L
± 0.5
Series name
Capacitance
Lot No.
Lot No.
Capacitance
Plastic platform
Plastic platform
Series name
Trade mark
Voltage (C : 16V)
Voltage (E : 25V)
Negative
Positive
Negative
Positive
A2 220E CL
Specifications
Item Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Stability at Low Temperature
Endurance
Shelf Life
Resistance to soldering
heat
Marking
– 55 to +105°C
6.3 to 50V
10 to 2200µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at
20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C .
Black print on the case top.
6.3
2
3
4
Z—25°C / Z+20°C
Z—40°C / Z+20°C
Z—55°C / Z+20°C
Measurement frequency : 120Hz
Measurement frequency : 120Hz at 20°C
Capacitance Change
tan δ
Leakage current
Within ± 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Capacitance Change
tan δ
Leakage current
Within ± 30% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Rated voltage
(
V
)
tan δ
(
MAX.
)
Rated voltage
(
V
)
Impedance ratio
ZT / Z20
(
MAX.
)
10
2
3
4
16
2
3
4
25
2
3
3
35
2
3
3
50
2
3
3
6.3
0.26
10
0.19
16
0.16
25
0.14
35
0.12
50
0.10
Tangent of loss angle (tan δ)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
CL
Low Impedance
φ D
4 to 6.3
8
(6.2L)
CL
CL
10
(7.7L)
CL
8 (10L)
•
10(10L,13.5L)
NL
Code
Trade mark
1
1: Size φ8 × 6.2 only
Pressure
relief vent
2
2 : Except : φ 10 × 7.7L
CD
Dimension table in next page.
CAT.8100B