Datasheet

LHseries
Chip Type, High Voltage.
High Reliability.
Chip type, High voltage and High Reliability.
Load life of 4000 hours at +125°C.
Applicable to automatic mounting machine
using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Performance CharacteristicsItem
LH
Series
Voltage(2G : 400V)
Lot No.
Plastic platform
0.3MAX.
φD±0.5
B±0.2
A±0.2 A±0.2
C±0.2
0.5MAX.
E
H
Positive
Negative
U
1
L
2
H
3
2
4
G
5
5
6
R
7
6
8
M
9
N
10
L
11
1
12
G
13
S
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated capacitance
( 5.6µF )
Rated voltage ( 400V )
Series name
Type
L±1.0
8 × 10
φD × L
A
B
C
E
2.9
8.3
8.3
3.1
10 × 10
3.2
10.3
10.3
4.5
10 × 13.5
3.2
10.3
10.3
4.5
L
10 10 13.5
H
0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
(mm)
Trade mark
A2 5.6 2G LH
Pressure relief vent
Capacitance
Chip Type
(φ8 × 10L, φ10)
Type numbering system (Example : 400V 5.6
µ
F)
ALUMINUM ELECTROLYTIC CAPACITORS
LT
Category
Temperature Range
–40 to +125°C
Rated
Voltage Range
160 to 450V
Rated
Capacitance Range
2.2 to 27µF
±20% at 120Hz, 20°C
Capacitance Tolerance
Measurement frequency : 120Hz
The specifications listed at right shall be met when the
capacitors are restored to 20
°C
after the rated voltage is
applied for 4000 hours at 125
°C.
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
160
6
200
6
250
10
400
10
450
15
Rated voltage (V)
tan δ (MAX.)
160
0.20
200
0.20
250
0.25
400
0.25
450
0.30
Measurement frequency : 120Hz at 20°C
Capacitance change
Leakage current
tan δ
Within ±30% of the initial capacitance value
Less than or equal to the initial specified value
300% or less than the intial specified value
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
The capacitors are kept on a hot plate for 30 seconds,
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Black print on the case top.
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After 1 minute's application of rated voltage, leakage current is not more than 0.04CV+100 (µA).
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
Dimensions
2.2
3.3
3.9
5.6
7.5
10
12
15
18
22
27
2R2
3R3
3R9
5R6
7R5
100
120
150
180
220
270
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
8 × 10
10 × 10
10 × 13.5
45
60
65
45
60
65
30
45
50
30
45
50
20
35
40
2C 2D 2E 2G 2W
160 200 250 400 450
V
Code
Cap.(µF)
Rated
ripple
Case size
φD
×
L (mm)
Frequency coefficient of rated ripple current
Coefficient
Frequency
50 Hz
0.70
1.00 1.17 1.36 1.50
120 Hz 300 Hz 1 kHz
10 kHz or more
Rated ripple current (mArms) at 125°C 120Hz
Long Life
CAT.8100B