Instructions / Assembly

ManualsBrandsNICOR ManualsDoorbell KitsPrimeChime Plus 2 Video Compatible Wired Door Bell Chime Kit

NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com May 29, 2020 4:02 PM PRCP2 Rev - Page 1 of 4

What’s In The Box

One (1) Prime Chime Plus Two (2) Lighted Doorbell Buttons

Prime Chime Plus

INSTALLATION INSTRUCTIONS

Model:

PRCP2

Tools Needed

The Prime Chime Plus requires very few tools for installation. A screwdriver and a pair of wirecutters will be

required to install the chime.

WARNING - RISK OF SHOCK

1. This xture is to be installed by only a qualied electrician.

2. This xture is to be used at 120V AC/60Hz power supply only.

3. This xture is designed for use in a circuit protected by a fuse or circuit breaker.

4. Turn o the power supply at the fuse or circuit breaker box before you install this xture.

5. Turn o the power supply again when you perform maintenance.

6. Double check all connections to be sure they are all tight and correct.

7. Operation environment: to be installed indoors under dry and ventilated environment. It should NOT be installed damp locations or

environment with high temperature. Installation of this xture should be kept away from other electrical devices.

One (1) Hardware Pack

Junction Box

Pre-install a dual voltage box (CARLON Model#SC200DV or equivalent, not provided) before installation of this device.

Video Doorbell Compatibility Notes

For all video doorbells:

1) To ensure proper operation of the PRCP2, no more than one video doorbell should be attached (Front Door or Back Door)

2) Make sure the video doorbell is fully charged prior to installation. Low battery levels may cause abnormal performance of the PRCP2.

3) Wiring must not exceed the following: 70’ from doorbell to rst unit. 200’ total length if installing more than one PRCP2

For Ring products:

1) Adjust the “Ring tone length” in the App to 2 seconds to avoid multiple chime cycles (see Ring instructions for details).

2) The Ring Power Kit (diode) should not be installed when using the NICOR PRCP2

Summary of content (4 pages)

PAGE 1
Prime Chime Plus INSTALLATION INSTRUCTIONS Model: PRCP2 WARNING - RISK OF SHOCK 1. This fixture is to be installed by only a qualified electrician. 2. This fixture is to be used at 120V AC/60Hz power supply only. 3. This fixture is designed for use in a circuit protected by a fuse or circuit breaker. 4. Turn off the power supply at the fuse or circuit breaker box before you install this fixture. 5. Turn off the power supply again when you perform maintenance. 6.
PAGE 2
Prime Chime Plus - INSTALLATION INSTRUCTIONS Model: PRCP2 Installing a single Prime Chime Plus 1 Carefully unpack fixture and faceplate. Make sure all power is turned off before beginning installation 2 Connect line voltage wiring (120VAC, 18ga or greater) per the diagram. 120V/60Hz only Junction Box 3 Connect low voltage bell wires (18ga or 22ga) into ports 1(+) and 2(-). 4 Black (Line) White (Neutral) Black (Line) White (Neutral) Install chime into junction box using four (4) included screws.
PAGE 3
Prime Chime Plus - INSTALLATION INSTRUCTIONS Model: PRCP2 Installing multiple Prime Chime Plus (2 max, 70’ spacing to first unit. 200’ total length) 1 Carefully unpack fixture and faceplate. 2 Connect line voltage wiring (120VAC, 18ga or greater) at each unit per the diagram. 120V/60Hz only Junction Box 3 Connect low voltage bell wires (18ga or 22ga) into the first unit into ports 1(+) and 2(-).
PAGE 4
Prime Chime Plus - INSTALLATION INSTRUCTIONS 7 For Button Installation see steps 6-7 for single unit installation. Note: Wiring of video doorbells is identical to standard doorbell wiring. Please follow doorbell manufacturer’s installation instructions for complete information. 8 Model: PRCP2 Apply power. The button should illuminate. Test functionality of the chime. Note: Wiring of video doorbells is identical to standard doorbell wiring (step 6).