Installation Guide

ManualsBrandsNICOR ManualsCommercial LightingT4AR Retrofit White Integrated LED Troffer in 4000K

LED TROFFER RETROFIT KIT

INSTALLATION INSTRUCTIONS

To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or

Canadian Electrical Code (CSA 22.1) in Canada.

Risk of re or electric shock. The electrical rating of these products are 120-277 Vac, the installer must determine whether they have 120-277 V

at the luminaire before installation.

Risk of re or electric shock. LED Retrot Kit installation requires knowledge of luminaires electrical systems. If not qualied, do not attempt

installation. Contact a qualied electrician.

Risk of re or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown below and where

the input rating of the retrot kit does not exceed the input rating of the luminaire.

To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot kit.

Check for enclosed wiring and components.”

Disconnect power before installing the product or servicing it.

Wait until xture has cooled down before installing or servicing the xture.

MIN. 90°C SUPPLY CONDUCTORS

Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other

open holes in an enclosure of wiring or electrical components.

What’s In The Box

Troer Retrot Installation

One (1) LED Troer Retrot kit xture

This LED Troer Retrot Kit requires

very few tools for installation. A drill or

a screwdriver and a pair of wirecutters

will help to remove the old ballast.

Sheet metal screws can be used to

attach the safety cables to the housing.

Carefully unpack the xture from its packaging. Inspect

product for defects due to shipping. NOTE: End Brackets have

oval slots.

Turn o power to appropriate circuit at the breaker panel.

Two (2) End Bracket Mounting

Brackets (with oval slots)

Two (2) Side

Mounting Brackets

Minimum dimensions for existing uorescent luminaire housing.

Housing Designation Overall inner Dimensions

2’ x 2’ 24” x 24” x 3.25” high

2’ x 4’ 48” x 24” x 3.25” high

Model(s):

T4AR-22-MV-35

T4AR-22-MV-40

T4AR-22-MV-50

T4AR-24-MV-35

T4AR-24-MV-40

T4AR-24-MV-50

Tools Needed

Summary of content (3 pages)

PAGE 1
LED TROFFER RETROFIT KIT INSTALLATION INSTRUCTIONS Model(s): T4AR-22-MV-35 T4AR-22-MV-40 T4AR-22-MV-50 T4AR-24-MV-35 T4AR-24-MV-40 T4AR-24-MV-50 To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA 22.1) in Canada. Risk of fire or electric shock.
PAGE 2
Troffer Retrofit Installation Continued 3 Remove existing lens/louvers, tombstones, ballasts, and ballast cover. Ensure that power wires are fed through housing after removing ballast. 4 Lift troffer housing and place both End Mounting Brackets under the existing housing. with the wide flat edge facing the floor and the notched edge facing the ceiling. 5 6 Next place the Side Mounting Brackets in the same way as the End Mounting Brackets. Attaching the bracket notches together as show.
PAGE 3
Troffer Retrofit Installation Continued 9 Connect wiring as shown. Grey and purple wires are for 0-10V dimming systems. Cap off if not used. Black (line) Black (line) Ground Green (ground) White (neutral) White (neutral) Purple (dim +) Purple (dim +) Grey (dim -) Grey (dim -) LINE 10 Swing fixture up, depress pins to lock into place. T4AR 11 NOTE: The 2 silicone “buttons” provide access if service is 12 Turn power on and verify that the panel is lit. needed.