Instructions / Assembly

ManualsBrandsNICOR ManualsAccent LightingUCB Series 18 in. Hardwired White Selectable Integrated LED Under Cabinet Light with On/Off Switch

NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com February 14, 2023 11:09 AM

What’s In The Box

One (1) UCB

One (1) Romex Connector

UCB LED Undercabinet

INSTALLATION INSTRUCTIONS

Models: UCB109*, UCB112*, UCB118*, UCB121*, UCB124*, UCB133*, UCB142*

Installation Steps - Under Cabinet Mount

WARNING:

• To reduce the risk of death, personal injury or property damage from re, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and

instructions included with and on the xture box and all xture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should be performed by a qualied licensed electrician.

• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualied licensed electrician and check your local

electrical code.

• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

• Turn o electrical power at fuse or circuit breaker box before wiring xture to the power supply.

• Turn o the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• All wiring connections should be capped with UL approved wire connectors.

• ATTENTION:

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

• Burn risk. Disconnect power and allow xture to cool before changing/handing xture

Tools & Materials Needed

This LED Undercabinet requires very few tools for

installation. A drill or screwdriver and a pair of wire

cutters will aid in installation.

Turn o power to appropriate circuit at the breaker box.

Remove the round knock-out in the luminaire housing

that is nearest the location of incoming power.

3 4

Three (3) Wire Nuts

Two (2) Mounting Screws

Remove the lens by squeezing and peeling away from xture.

Open the driver cover by uncliping tray and swinging open.

Position the housing in the desired location then mark and

drill mounting holes at the narrow ends of the keyhole slots.

Screw in mounting screws leaving space for housing thickness.

Slide housing over mounting screws, shift into position and

tighten screws.

Summary of content (3 pages)

PAGE 1
UCB LED Undercabinet INSTALLATION INSTRUCTIONS Models: UCB109*, UCB112*, UCB118*, UCB121*, UCB124*, UCB133*, UCB142* WARNING: • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 2
Installation Steps - Under Cabinet Mount(continued) 5 Using the included cord grip, insert supply wiring into housing and make wiring connections per the wiring diagram. 6 Reattach the driver cover, pressing until it is retained by 3 Reattach the lens to the housing, making sure it is fully installed across its length. 4 Apply power and test for proper function. For model with On/ Off switch, test to control illumination. The CCT selection slider can be positioned to the desired color temperature.
PAGE 3
Installation Steps - Wall Mount with 4/O box (continued) 5 Position the housing in the desired location then mark and drill mounting holes at the narrow ends of the keyhole slots. Screw in mounting screws leaving space for housing thickness. Slide housing over mounting screws, shift into position and tighten screws. 6 Reattach the driver cover, pressing until it is retained by 7 Reattach the lens to the housing, making sure it is fully installed across its length.