Installation Guide

ManualsBrandsNICOR ManualsCommercial LightingVaportite Series 200-Watt Black Integrated LED Vaportite Work Light in 5000K

NICOR, Inc. | 2200 Midtown Place NE, Albuquerque, NM 87107 | 800.821.6283 | www.nicorlighting.com | June 15, 2015 3:00 PM

VT1 Extreme Environment LED Vaportite

INSTALLATION INSTRUCTIONS

Model: VT1-10H-UNV-50K-BK

VT1-10S-UNV-50K-BK

IMPORTANT - READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS

PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE

CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture.

No user serviceable parts inside.

NOTE: when drilling holes in the plastic J-box, it is highly recommended to use a stepped drill bit to lessen the chances of personal

injury or damage to the xture

The VT1 Extreme Environment LED Vaportite is designed for use in

demanding applications. Thermally conductive plastic & noncorrosive

materials make this xture a versatile choice for any environment.

Carefully unpack the unit from its packaging and inspect for defects

before installation.

Loosen the four screws holding the junction box top to the main

body. It is not necessary to completely remove the screws as they

will be retained by the capture tab, making later re-installation more

convenient. Remove the j-box top. Determine the desired mounting

method: hanging, pendant, or surface mount.

Note: if 0-10V dimming is to be enabled, please go to 0-10V dimming

installation.

Chain or Cable Hanging Mount

Drill the appropriate sized hole in the top of the black plastic junction

box to accommodate the cable gland. Install the cable gland and feed

the AC supply line through the gland into the top of the junction box.

Secure a cable/chain hook to each of the 4 corner mounting loops

on the main xture body. Secure the cable/chain to the supporting

structure, and hang the xture in the desired position being sure to

follow all UL, NEC, and minimum load ratings guidelines.

Feed the AC supply line through the cable gland into the top of the

junction box and tighten the seal around supply line. Connect the

xture driver AC input wires to black (line), white (neutral), and the

xture green grounding tether wire to ground using UL listed wire

connectors.

Re-install the top of the junction box onto the main xture and secure

with the 4 screws. Take care to ensure all wires are inside junction box,

the junction box is seated properly on the gasket, and not to over-

tighten the screws thus cracking the plastic screw bosses.

Warranty

For complete warranty information please visit :

http://nicorlighting.com

Drilling

Location

Summary of content (3 pages)

PAGE 1
VT1 Extreme Environment LED Vaportite INSTALLATION INSTRUCTIONS Model: VT1-10H-UNV-50K-BK VT1-10S-UNV-50K-BK IMPORTANT - READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety.
PAGE 2
INSTALLATION INSTRUCTIONS - (Continued) Pendant Mount To pendant mount this fixture either, (1) purchase an Angled Ceiling Adaptor Kit, Wire Extension Kit & Downrod for Ceiling Fans available at Home Center stores and install per instructions included in the Kit. Or (2) purchase a ¾” NPT(1” outer diameter) fixture conduit stem threaded on both sides, wire of desired length and a commercial flexible fixture hanger or swivel hanger.
PAGE 3
INSTALLATION INSTRUCTIONS - (Continued) 0-10V Dimming Installation 3 After removing the top of the junction box, slide the metal separator 3 plate out. 4 Depending upon the cable gland used, (for example: Weidmueller VG M20-1/K68) drill the appropriate sized hole in the side of the lower j-box such that the hole in the plastic j-box coincides with one of the holes in the aluminum heat spreader plate.