C3-RS-727A LCD PROFESSIONAL 2-WAY LCD REMOTE CAR STARTER & ALARM SYSTEM With Built in Temperature sensor And Two-way Serial Port Data Link Compatible Please see page 23 of this manual for more details OPERATION MANUAL Please register your product at: www.autopageusa.
TABLE OF CONTENTS: A B C LCD REMOTE TRANSMITTER: BATTERY REPLACEMENT THE REMOTE LCD ICONS WITH FUNCTION PROGRAMMING OF THE LCD REMOTE TRANSMITTER 1. Screen Lamp ON 2. Power Save Mode 3. Clear The Flash Icon and Melody Sound 4. Stop The Melody Sound. 5. Button Lock 6. Vibration / Melody Mode 7. Enable / Disable Bi Sound While Pressing Button: 8. Low Battery Indication. 9. Set Up Fixed Count Down Timer 10. Out Of The Range Check D CLOCK & TIMER SETTING 1. Clock Setting. 2. Alert Alarm Timer Setting 3.
M N PANIC FUNCTION TRIGGER THE SYSTEM Clear The Trigger Icons and Melody Sound Stop The Melody Sound Only Noise Abatement Circuit O ANTI CAR- JACKING Active Anti Car Jacking Passive Anti Car Jacking Trigger The Anti Car Jacking Mode Override The System To Turn Off Anti Car Jacking P Q R S T U V W X SYSTEM’S TRIGGER CHECK SYSTEM’S STATUS CHECK DRIVER PAGING (OPTION) DOME LIGHT CONVENIENCE DELAY & SUPERVISION IGNITION CONTROL THE DOOR LOCK/UNLOCK TRUNK RELEASE (CHANNEL 3) OUTPUT CHANNEL 4 TIMER CONTROL O
Auto Page, Inc. has over 25 years of experience in the vehicle security industry in the United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan. Iwata has been an industry leader for over 50 years, establishing a reputation for ingenuity in its engineering capability and innovative communication products. Auto Page and Iwata maintain a long tradition of providing the best value to their customers. TRANSMITTERS The RS727A comes with two transmitters.
WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. 2. 3. 4. 5. 6. 7. 8. 9. Keep the transmitter out of children’s reach. Do not leave anyone in the vehicle while running on remote control. Alert servicing personnel that the vehicle can be started automatically. Do not start the vehicle by remote while it’s in an enclosed area or garage. Always apply the parking brake and lock the vehicle as you exit the vehicle.
A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons. Correct the time by pressing for 3 seconds before using (See Timer Setting).
Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle Button Lock Disable the transmission function temporarily Low Battery You have to replace the battery of remote control. C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button (1 second) Description LCD screen lamp turns on for 5 seconds. (3 seconds) Timer Programming Mode.
exit the “Power Save Mode”. 3. Clear the Flash Icon and Melody Sound: Pressing the button 3 times within 3 seconds will clear the flash icon and the melody sound on the LCD screen transmitter. 4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will alert the user through a melody sound and a flashing trigger icon. Press any button on the LCD remote transmitter to stop melody sound only. 5.
2. Press the ( ) button again showing next order time on the screen (ie.0: 20), press them again (ie.0: 30)…and so on. 3. After the timer is set the count down begins when the icon flashes Note: 1.The count down period is fixed as 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5 hours and 2 hours maximum. a. When the count down timer shows 0:00 it means to turn off the timer. b. Press button for real time indication when the timer is counting down. 10.
Press 4 button once Press & hold the button for 2 seconds. Count down Timer Setting ON / OFF for OFF and ON for Daily Timer Start Timer Setting Flash / icon and “Hours” for adjusting for – and for + EXIT: Press and hold the button for 2 seconds or leave it for 10 seconds, the system will exit the programming mode. 1. Clock Setting: Example to AM10:30 1. Press & hold the button for 3 seconds,two-melodies will sound and the “Hours” digit flashes for adjusting. 2.
timer program mode. Note: Maximum is 19 hours. 4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30 1. Press & hold the button for 3 seconds, two-melodies will sound and the “Hours” digit will flash for adjustment. 2. Press & hold the button for 2 seconds, the LCD screen will flash the / icons and “Hours” digit for Hour set-up. 3. Press or button to decrease or increase the hour digit until AM 6:00 4. Press the button once again then the minute digit will flash. 5.
- ( ) - ( ) - ( ) - - - + Optional Driving Pager Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds Daily Timer Start Press within 3 seconds LCD screen lamp turns on for 5 seconds. Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Switching code for 2nd / 1st Car Operation Press and hold for 1 second Press within 3 seconds Press within 3 seconds and Hold and seconds buttons together for 2 C.
1. Press button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle’s doors will lock upon arming if interfaced with the security system. System Arm Door Ajar Trunk / Hood Ajar Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed. The vehicle’s doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door locks and dome light must be installed with the security system.) System Disarm Doors Trigger Trunk/Hood Trigger Shock Sensor Trgr Ignition Trigger Clear The Flash Icon: Press the button 3 times within 3 seconds to clear the flash icon on the LCD screen transmitter.
releasing the Valet Switch. 5. Turn the ignition switch “OFF” position. 4 Chirps from siren/horn and 3 flashes from the parking lights will indicate the system has disarmed. Note 1: You must override the alarm within 60 seconds. If not, the system will automatically re-arm. EXAMPLE: To Override The System With The Password Code 83, 1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.) 2.
1. Press and hold the button for 3 second. The alarm will immediately sound. 2. During panic mode, the normal function of this transmitter button will be disabled. The transmitter and buttons can be used to lock and unlock the door (if the option is installed), however once the button is pressed, the vehicle’s starter disable device, (where installed) will be disengaged allowing the vehicle to start. 3. To stop the alarm, press and hold the transmitter or button on the transmitter again for 3 seconds.
“Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for six full cycles, the doors will be bypassed until the trigger ceases. O. ANTI CAR- JACKING Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”. This system is default setting all car jacking “OFF”. ACTIVE ANTI CAR JACKING: 1. Press and hold the transmitter and buttons at the same time for 2 seconds while the vehicle’s ignition is ON.
Q. SYSTEM’S STATUS CHECK When you want to check the system’s present status through the LCD screen, Press the transmitter button twice. Within 3 seconds press the (C) button. It will respond with one melody sound. Note: If it has no response then you are out of range. R. DRIVER PAGING In the event that someone wan ts to page the driver of the parked vehicle. In Car Driver Paging With the ignition in the switched “off” condition, press and hold the valet switch for 2 seconds to page the driver.
U. CHANNEL 3 (TRUNK RELEASE) OUTPUT. Press and hold button on the transmitter for two seconds to remote control the trunk release or other electric devices. (If Installed as an Available Option) V. CHANNEL 4 TIMER CONTROL OUTPUT Press the transmitter (4) and (4) buttons at the same time to active Channel 4 function. Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds.
1. Press first, within 3 seconds press and hold and buttons at the same time for 2 seconds. Two beeping sound and the “ ” icon will be displayed on the LCD screen to indicate the second transceiver pin code is programmed. 2. While the “ ” icon is displayed on the LCD screen , you can remote control and communicate with a second vehicle security system. It has two short “bi” sounds while pressing the button of the LCD screen transceiver. Back to 1st Car Operation: 1.
4. The gear selector is in any gear other then “PARK” or “NEUTRAL” SAFE START (Child safety mode) Factory default is set to press the button once on the transmitter to start the vehicle. You can program this feature to eliminate an accidental remote start: 1. The user presses the transmitter buttons twice within 3 seconds to start the vehicle. or 2. The user presses the transmitter the vehicle. and buttons at the same time to start NOTE: Contact your installing dealer to activate this feature. B.
-- The LED will flash indicating the remote start has entered the turbo charge mode. 3. Take the “Ignition Key” from the key cylinder. -- Engine keeps running. -4. Exit and secure the vehicle. -- Engine continues running until the pre -programmed time elapsed. -- NOTE: This feature only applies to vehicles with Turbo Engines. E.
With the built in temperature sensor you can monitor, Through the LCD screen, the present indoor temperature of the passenger compartment before cooling or heating your vehicle. Press the transmitter buttons first, within 3 seconds press ( ) button; the in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature. G.
2. This WARRANTY will be considered void if the equipment has been misused, neglected, improperly serviced or installed, altered, dropped or damaged by water, contrary to the Auto Page OPERATIONS MANUAL. Or, if used with accessories not approved by Auto Page, which may have contributed to the defect. See note below regarding product installation**. 3. The purchaser’s remedies under this WARRANTY shall be limited to the repair or replacement of electronic components only.
It is recommended to have a minimal digital service plan on your cell phone Your RS-727A is CI3 compatible and will open your world to the true power of two way communication. Complete tracking and full cell phone functionality can be added to your system. Fo r more information please visit your local authorized Autopage dealer or go to www.autopageusa.com .
Compatible 2-Way Communication to the Power of 3 960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.