NMD340 – Microset USER MANUAL EN © Elmarc, 17/03
Table of contents 1 Intended use 3 2 Safety 4 2.1 Labels in this manual 4 2.2 General safety instructions 4 3 Preparations for use 3.1 Unpacking 3.2 Package contents 6 6 6 4 4.1 4.2 4.3 4.4 7 7 7 8 8 Installation Install batteries Connecting the system Connecting random equipment Connecting to the mains 5 Functions 5.1 Remote control 5.2 Microset 10 10 12 6 6.1 6.2 6.3 6.4 6.5 6.6 6.
1 Intended use The Microset plays music from CDs and music, videos and photos from DVDs and USB. Music can also be played via the LINE-IN port. The FM function lets you listen to the radio. The appliance also plays photos from Kodak picture CDs. The Microset can be controlled by bluetooth. Read the manual carefully before the first use.
2 Safety 2.1 Labels in this manual 66 WARNING A warning means that injury or death is possible if the instructions are not obeyed. 11 CAUTION A caution means that damage to the equipment is possible. 55 A note gives additional information, e.g. for a procedure. 2.2 General safety instructions 66 Please note! Install the product as indicated in this manual. If in doubt, consult a recognised technician and always take account of local installation codes and regulations.
11 CAUTION Do not block the ventilation holes. 55 This appliance is double insulated; therefore no earth wire is required. Always check that the mains voltage corresponds to the voltage on the rating plate. 55 This appliance employs a laser system. To prevent direct exposure to the laser beam, do not open the appliance. Visible laser radiation when open and interlock defeated.
3 Preparations for use 3.1 Unpacking • Unpack the appliance carefully. • Check the package contents as described below. If any item is missing, please contact your reseller. • Remove the labels from the front panel carefully if present. 55 We recommend that you retain the original carton and packing materials in case it ever becomes necessary to return your product for service. This is the only way to safely protect the product against damage in transit.
4 Installation 4.1 Install batteries 1 2 3 • Remove the battery cover. • Insert the batteries matching the (+) and (-) polarity markings. • Re-install the battery cover. 11 CAUTION Incorrect installation can cause battery leakage and corrosion which will damage the appliance. Corrosion, oxidation, battery leakage and any other gradually acidic defect of this nature will invalidate the guarantee. 4.2 Connecting the system • Connect the speakers to the appliance.
4.3 Connecting random equipment Connect the tv • Use one of the cables as presented in the image below. • Insert an FM aerial or a suitable cable into the FM ANT IN connection. 4.4 Connecting to the mains • Connect the appliance to the mains.
• Switch on the appliance.
5 Functions 5.1 Remote control 20 1 21 22 2 3 5 7 9 11 13 15 17 19 24 4 26 6 28 8 30 10 32 12 34 14 36 16 38 18 40 1. STANDBY button 2. Digit buttons 3. 10+ button 4. PROGRAM button 5. Stop button 6. SOURCE button 7. Arrow key up 8. MENU button 9. Arrow key left 10. ENTER button 11. SETUP button 12. DVD/USB button 13. SEARCH button 14. SUBTITLE button 15. ANGLE button 16. COPY button 17. N/P button 18. ZOOM button 19. V-MODE button 20. MUTE button 21.
General functions SOURCE button • To select the source mode TUNER/LINE IN/BLUETOOTH/DVD, press the SOURCE button (6). TUNER LINE IN DVD Selecting source mode USB • To select the source mode DVD, press the SOURCE button (6). • Press the DVD/USB button (12). FUNCTION button BASS and TREBLE can be adjusted using the FUNCTION (28) key. BASS • Press the FUNCTION (28) key 1 times to select BASS. • Press the VOL+ (26) VOL- (27) key to set the BASS. TREBLE • Press the FUNCTION (28) key 2 times to select TREBLE.
5.2 Microset 5 6 7 8 9 1 2 3 4 10 11 12 13 14 18 19 15 16 17 1. STANDBY button 2. Stop button 3. USB slot 4. Headphone jack 5. CD compartment 6. LCD Display 7. OPEN/CLOSE button 8. Play/Pause button 9. Volume dial 10. Connection to speakers 11. Aerial connection (FM radio) 12. Line in jack 13. Digital output: HDMI 14. COMPONENT 15. COAXIAL 16. VIDEO 17. S-VIDEO 18. On / Off key (POWER) 19. AC~ POWER Headphone jack • To connect a headphone, insert the cable plug in the headphone jack.
6 Operation 55 All functions of the appliance are accessible using the remote control. All instructions refer to operation with the remote control, unless indicated otherwise. 6.1 General setup menu operation 7 9 11 6 10 31 32 This chapter explains a complete setup of the appliance: settings of screen display, audio setup and video setup. Preparation • Turn on the television. • Switch on the device. • To select the source mode DVD, press the SOURCE button (6). • Press the SETUP button (11).
The GENERAL menu Picture format • In the TV DISPLAY section, press the arrow buttons (7,9,31,32) to select 4:3 4:3 PANSCAN or 4:3 LETTERBOX for a conventional TV set. Select 16:9 for a wide screen TV set. ANGLE MARK • In the ANGLE MARK section, press the arrow buttons to switch this function ON or OFF. When switched ON, the appliance shows the angle mark when multi-camera angles are available. 55 The ability to use this feature depends on the type of DVD.
The AUDIO menu SPEAKER SETUP Select the desired sound with this view (STEREO, LEFT, RIGHT) SPDIF SETUP Set the digital audio signal. • Select SPDIF OFF to switch off the digital audio signal output. • Select SPDIF RAW to set the digital audio signal output to its raw format (DTS/Dolby Digital 5.1). • Select SPDIF PCM to set the digital audio signal output to PCM format. The DOLBY DIGITAL menu Dolby digital audio setup DUAL MONO In the DUAL MONO area, you can choose: • STEREO: for stereo effect.
HDMI SETUP • HDMI: select ON / OFF to turn HDMI on / off. The PREFERENCES menu Preference setup page TV TYPE • Select the video output format to match the appliance to the TV system: PAL, AUTO or NTSC. 55 The video output format can only be selected when the DVD tray is empty. 55 Please note: if the wrong option has been selected, this may result in very poor image quality. In that case, select a different setting. AUDIO • In the AUDIO section, choose the audio language.
DEFAULT Restore all default settings of the appliance, except the settings for the menu items PARENTAL and PASSWORD. 6.2 DVD/CD functions 21 22 2 24 5 7 9 11 4 6 8 10 30 32 34 15 14 18 36 23 25 29 31 33 35 37 41 Preparation • Turn on the television. • Switch on the device. • To select the source mode DVD, press the SOURCE button (6). • Press the OPEN/CLOSE button (21). • Insert a CD/DVD. After the disc has been loaded, a content menu will display on the TV screen.
• Press the arrow buttons (7,9,31,32) to select a menu item. • Press the ENTER button (10) to enter the selected menu item. • To start playback, press the PLAY/PAUSE button (29) once. During playback, the following functions are available: • To select a chapter (DVD) or track (CD), press the digit buttons (2). • To select the next or previous chapter (DVD) or track (CD), press the PREV button (22) or the NEXT button (23). • To forward or rewind the DVD, press the FWD button (24) or the REV button (25).
• To cancel the A-B REPEAT function, press the A-B REPEAT button again. The appliance will resume the normal playback. 55 Please note: Normally, if an MP3 disc is loaded, the unit will take longer time to read the initial data. A DVD that does not match the region code cannot be read by this appliance. If a disc contains mixed content (e.g. MP3 and video files), the appliance will only recognise, list and play one content type.
Using the ZOOM function This function can be used for zooming in and out on photos and DVDs. The available zoom ratios are: 2x, 3x, 4x, 1/2, 1/3, 1/4. • Press the ZOOM button (18). • Press the ZOOM (18) button again to set the correct size. • Press the arrow buttons (7,9,31,32) to move through the picture. Using the Kodak picture CD playback function • Insert a Kodak picture CD. • Press the STOP button (5) to enter the thumbnail mode. Choose an option (Slide show/Menu/prev-next) and press ENTER (10).
6.3 Copy content from a CD to a USB device 55 Ensure there is sufficient free space on the USB device. 1 21 2 5 7 9 6 10 31 32 12 16 Preparation • Turn on the television. • Switch on the device. • To select the source mode DVD, press the SOURCE button (6). • Press the OPEN/CLOSE button (21). • Insert a CD. • Press the DVD/USB button (12). • Press the STOP button (5). • Press the COPY button (16). Copying a file from one source to another source • Select the desired file using the (7,9,31,32) keys.
6.4 Radio functions 22 2 24 4 23 25 6 13 Preparation • Switch on the device. • Press the SOURCE key (6) to select the radio mode. Program radio stations automatically • Press the SEARCH button (13). 20 stations are being searched and stored automatically. • Press the PREV (22) Button or the NEXT (23) Button to select the desired station. Programming a radio station manually • Turn on the television. • Press the FF- (24) Button or the FF+ (25) Button to select the desired station.
6.5 USB functions 1 22 2 5 7 6 29 8 10 23 32 12 Preparation • Turn on the television. • Switch on the device. • Insert the USB device in the slot . The device can only be connected one way. • To select the source mode DVD, press the SOURCE button (6). • Press the DVD/USB button (12). After the device has been connected, a content menu will display on the TV screen. • Press the arrow button (7,32) (up and down) to select a folder or a file.
• Press the arrow button (7,32)(up and down) to select a folder or a file. • Press ENTER (10) to confirm. • Press the MENU button (8) to return to the content menu during playback. During playback, the following functions are available: • To select a track, press the PREV button (22) or the NEXT button (23) until the desired track is set. • To pause playback, press the PLAY/PAUSE button (29) once; to resume playback, press the button again. • To stop playback, press the STOP button (5).
6.6 LINE-IN 1 6 Preparation • Switch on the device. LINE IN • To connect an external audio device, insert the cable plug in the LINEIN jack (). • To select the source mode LINE-IN, press the SOURCE button (6). "LINE-IN" appears on the display.
6.7 Operation with BLUETOOTH PINcode 0000 Connected Max. 10m 6 55 You can wirelessly connect the device to devices that have Bluetooth A2DP. Preparation • Switch on the device. • To select the source mode BLUETOOTH, press the SOURCE button (6). "BT" appears on the display. You will see the blue LED flashing (3x). You will hear a beep. Bluetooth mode is now activated. • The device will first search for devices with which it has previously established a Bluetooth connection.
Your device is now ready to establish a wireless connection with your Bluetooth device. Establishing a Bluetooth connection (PAIREN) • Turn on the Bluetooth function of your device • Go to the Bluetooth Menu of your Bluetooth device. • Search Bluetooth devices and select (...) to establish connection • Enter "0000" when the player asks for the PIN code The blue LED will flash slowly as soon as the connection has been established You will hear a beep.
7 Cleaning and maintenance 66 WARNING Before performing any cleaning or maintenance, switch off and unplug the appliance. • Clean the outside of the appliance with a soft cloth. When the appliance is very dirty, dampen the cloth slightly with water and a neutral solution. 7.1 Handle and care of a disc 11 Hold the disc with fingers. Hold the disc outer edge and/or the centre spindle hole. Do not touch the disc surface. 11 Do not bend or press the disc.
8 Technical data NMD340 Microset • Voltage: 220-240VAC ~ 50/60 Hz • Power consumption: ...
9 Disposal of used electric and electronic equipment The meaning of the symbol on the material, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical and electronic equipments waste. In the European Union and Other European countries which there are separate collection systems for used electrical and electronic product.