Install Software 18 Click 19 Click R2-D2™ Skype Web Cam 27
Install Software 20 21 Click Install dialer.
Install Software 22 Click File will be copied onto the computer. Memo If you wish to change installation folder, click on the [Browser] button and specify the desired location.
Install Software 24 Install screen key.
Install Software 26 Click Memo If you wish to change installation folder, click on the [Browse] button and specify the desired location.
Install Software 28 Click 29 Click Software installation has completed. Next, proceed with the New Hardware Search Wizard.
Install Software New Hardware Search Wizard This wizard is to confirm that the driver and/or software have been successfully installed. 1 Make sure that the camera viewer is not activated. 2 Connect the stand to the computer with the USB cable. (Refer to page 40.) 3 1) Click to select.
Install Software The search starts and the screen shown below will be displayed. The search takes a few minutes to complete. 4 1) Click to select.
Install Software 5 2) Click Installation starts.
Install Software Confirm the Installation Result Confirm if driver and software have been installed successfully. 5 Confirm driver installation 1 2 3 4 Connect computer, stand and lightsaber with USB cable. (Refer to “USB Cable Connection” on page 14) Make sure that this has been added Click [Start] – [Settings] – [Control Panel]. Double-click the “System” icon. Memo If “!” mark is attached to Trident Analog Video, disconnect the USB cable from computer and reconnect it.
Install Software Confirm audio device installation 1 2 3 4 1) Click Connect computer, stand and lightsaber with USB cable. (Refer to “USB Cable Connection” on page 40) Make sure that “NIKKO R/C” has been selected Click [Start] – [Settings] – [Control Panel]. Double-click the [Sound and Audio] icon. 3) Click Memo If “NIKKO R/C” has not been selected, display the list and select “NIKKO R/C”.
Preparation Before Use Install batteries in R2-D2 and lightsaber. Connect computer, stand and lightsaber with USB cable. 3 2) Install batteries 1) Open the battery cover Install Batteries Install dry cell batteries in R2-D2 and lightsaber. Note: Make sure to use AA alkaline dry cell batteries. Note: Be careful of the battery polarity when installing the batteries. R2D2 4 1 1) Close the battery cover 2) Slide the battery cover to the right until it clicks.
Preparation Before Use 3 Lightsaber 1 Insert the LED indicator until it clicks. Press the LED indicator stopper button (2 places) simultaneously. Note: Make sure that the LED indicator is installed straight. 2) Install batteries 2 1) Pull out LED indicator Note: Be careful of the battery polarity when installing the batteries.
Preparation Before Use USB Cable Connection Stand R2-D2 Connect computer, stand and lightsaber with USB cable. Stand R2-D2 by moving its both arms. Computer Lightsaber Open the connector cover. Stand 4 3 1 2 USB cable 1m (with a tag indicating “LIGHTSABER”) USB cable 2m (with a tag indicating “STND”) Move the arms towards the rear side until a clicking sound is heard. Note: To avoid damage, do not force to move the arms beyond their movable range. Note: Be careful of polarity of USB connector.
Preparation Before Use Turn on R2-D2 Power Set the power switch on the bottom to the ON position. LED indicator on the head lights up when the power turns on. ¯ If unusual operation or symptom is observed due to static electricity, open and close the battery cover and then turn on R2-D2 power again. LED indicator ON: Turns on the power. LED indicator lights up in blue. OFF: Turns off the power. LED indicator turns off. R2-D2™ Skype Web Cam Standby: Turns on the power. LED indicator lights up in blue.
How To Use Start Software Software can be started from R2-D2 launcher. 1 2 3 Click the desired parts of R2-D2 launcher. Activates camera v i e w e r. ( R e f e r t o page 43) Turn on R2-D2 power. (Refer to “Turn on R2-D2 Power” on page 41) Double-click on the desktop. R2-D2 launcher starts. Note: Do not disconnect the USB cable from you computer and connect again during R2-D2 operation. This will caused your computer to auto-restart.
How to Use Operate Camera Viewer Memo The camera does not mainly focus on capturing image of people. 1 Double-click on the desktop. R2-D2 launcher starts. 2 Click the camera Camera viewer starts.
How to Use 3 Click button to operate.
How to Use No. Name Function 1. Minimize icon Minimizes camera viewer window. 2. Close icon Closes camera viewer. 3. Zoom in For digital zoom in. Displays close shot. 4. Full screen display Displays full-screen camera viewer window. 5. Zoom out For digital zoom out. Displays far shot. 6. Sound detect slider Adjusts the sensitivity of the sound sensor. Sliding to the left makes the sensor react to a softer sound while sliding to the right makes the sensor react to a louder sound.
How to Use 4 Close camera viewer when operation is complete. Click Memo The image might not be clear due to poor signal reception condition. The condition may improve if you change the orientation of R2-D2 or move it to a different location. Memo Press the menu screen display button and make the settings for [Sound] and [Channel]. • [Sound] Use this product while the Sound is set to OFF. If it is set to ON, change it to OFF. • [Channel] 5 Turn off R2-D2 power.
How to Use Operate R2-D2 You can move R2-D2 freely using computer or lightsaber. Note: Cautions on moving R2-D2 Fall prevention sensor may not function on table with complicated shape such as round table or table with an uneven edge. This product is designed to be moved on a flat and level surface. Please be noted that fall prevention sensor cannot always detect difference in surface level. Memo You can do the followings when the camera viewer is activated.
How to Use 4 Left turn Move forward Right turn Click the camera Counterclockwise pivot turn Camera reactivation (¯) Click this part of R2-D2 Clockwise pivot turn Right turn Left turn Tilt the camera upwards Screen key and camera viewer are activated. 5 Click buttons to operate R2-D2.
How to Use 6 Click again to complete operation Screen keys are closed. 7 8 9 Close the camera viewer. Turn off R2-D2 power. (Refer to “Turn on R2-D2 Power” on page 41) Connect USB cable to lightsaber.
How to Use Operate with lightsaber Memo Make sure that USB cable is properly connected to lightsaber. 1 2 3 4 Double-click on the desktop. R2-D2 launcher starts. Click Turn on R2-D2 power. (Refer to “Turn on R2-D2 Power” on page 41.) Click the camera. Click this part of R2-D2 Memo When [TALK] is pressed, lightsaber functions as an IP phone and R2-D2 cannot thus be operated with lightsaber. Memo If [OFFLINE] is selected, the mode is set to [CONTROL] automatically.
How to Use 5 Open the cover of lightsaber. 1) Press 2) Turn 6 1) While pressing the button on the grip, 2) turn the grip clockwise to open the cover. The grip turns only in a single direction. Please note that the grip may get damaged if you attempt to turn the grip in the reverse direction. Just as opening the cover, turn the grip clockwise to close the cover. When closing the cover, stop turning the grip when you hear a click sound and the button on the grip pops up. Press buttons to operate R2-D2.
How to Use 3 Talk on Skype 1 Double-click on the desktop. R2-D2 controller is activated. 2 Click the Skype button on R2-D2. 1) Click Click this part of R2-D2. 2) Click Memo When [CONTROL] is pressed, lightsaber functions as an R2-D2 controller and it cannot thus be used as an USB phone. Skype starts and screen key is activated.