User's Manual

Nikko MicroRadioControl System”iTruck”
RDC-700600
-2-
-3- -4-
-1-
For ages 6 and over
Manual of Instructions
*Thank you for choosing NIKKO iTruck!
*Read this Manual of Instructions care-
fully to the end before starting to play.
*Don’t throw away the box or this
manual, but keep them for future use.
*The actual product may differ slightly
from the illustrations.
Features
*The controller (transmitter) has a built-in battery recharger. Attach iTruck to the controller
for quick recharging and lasting power.
*A large volume, high-power nickel metal hydride battery is built into the chassis.
*The controller has only 1 control stick. Forward-backward running, left-right turns, and
stopping are all possible with single-hand operations.
Battery requirements:
Size "AA" "UM3" "R6" alkaline batteries x 2 (No other type of battery should be used)
Battery Characteristics and Recharging Tips
When playing for the first time after purchase, or after a long interval, the battery power
may be weak. Even after recharging, the running time can be relatively short. The
battery will gradually regain power after 2 or 3 repetitions of usage and recharging.
Also, if you keep the power switch turned ON for a long time, the battery power will be
discharged. Make sure to turn OFF the power switch immediately after use.
Names of the Parts
iTruck
Receiver
antenna
Top side
Steering
alignment
lever
Power switch
Bottom side
Recharging
terminal
(iTruck side)
Charger cover
CONTROLLER
Center marker holder
Recharging
terminal (control-
ler side)
release button
Power switch
Recharging monitor
lamp (green LED)
Control stick
Top side
Transmitter antenna
Battery lid
Bottom side
safety hook
removal button
How to Install the Controller Batteries
Use a ballpoint pen to open
the battery lid.
Install 2 alkaline
batteries
Battery installation:
*Install the batteries in the controller.
(This product operates only with size "AA" "UM3" "R6"alkaline batteries. If you use man-
ganese or other types of batteries, the nickel metal hydride battery built into the vehicle
may not be recharged fully. Be sure to use ONLY alkaline dry cell batteries.)
Make sure that the power switch of the controller is turned OFF.
Use a ballpoint pen, pencil or sharp tools to push the release button of the battery
lid. While pressing the button, slide the lid a little bit as shown in the diagram.
*Slide out the lid with your hand and detach.
*Be careful so that the pencil lead will not be broken.
Install 2 size "AA" "UM3" "R6" alkaline batteries, making sure that the (+) and (-)
ends are positioned properly.
Attach the battery lid again. Slide the lid back into position until the release button
clicks. (Lift up the rear end of the battery lid slightly to fit the lid into the groove as
shown in the diagram. Then, keep the lid flat and slide into the groove.)
There is a safety hook on the controller to prevent ve-
hicle from falling off while recharging. When vehicle is
fully recharged, the green LED lamp will turn off. When
this has been confirmed, keep pressing the recharg-
ing release button on the side of the controller, and
pull vehicle toward you to detach it from the controller.
removal
button
iTruck power
switch is turned
OFF
Controller
power switch
is turned ON
Open the charger
cover
Fit the claw of the con-
troller into the hollow
pit of the chassis.
Slide iTruck forward until
you hear a click.
The set-up is completed!
Check to see that iTruck does
not fall off.
The green LED
lamp lights up.
The ordinary recharging time is about
2 minutes. (The LED lamp will turn
off when recharging is completed.)
Contents of the Kit
iTruck x 1 Controller x 1
Manual of
Instructions x 1
close the lid.
If the product is used in low temperatures, the battery duration can be shorter than
normal. This is a characteristic feature of the battery and is not a defect. The situation
can be improved by recharging the battery immediately before playing. The battery
power tends to be weakened as time elapses.
When you have finished recharging, de-
tach iTruck from the controller and replace
the recharger cover.
Fit into the groove.
To remove the bot-
tom battery more
easily, press the mi-
nus (-) end with
your finger and pull
out the plus (+) end.
Procedures for Recharging iTruck
(Remove dust or filth from the charger Recharging terminal.)
Follow the correct procedures when recharging.
When the battery starts to run out of power, the LED lamp will grow dim.
1 2
3
4
1 2
3 4
5 6
7
8
ATTENTION PARENTS
It is recommended that this toy and
all accessories be periodically ex-
amined for potential hazards and
that any potentially hazardous
parts be repaired or replaced.
IT IS A VIOLATION OF THE FCC REGULA-
TIONS TO REMODEL OR ALTER THIS DE-
VICE IN ANY WAY WITHOUT PERMISSION,
ANYONE WHO VIOLATES THE REGULA-
TIONS WILL LOSE THE RIGHT TO OPERATE
THE DEVICE.
Repair and Parts Department
Monday to Friday 8:30AM-5:30PM Central Time
Repair:[phone]
Parts:[phone]
Fax:[phone]
e-mail:[e-mail]