Owner's Manual
Table Of Contents
- User Manual
- Table of Contents
- Get SnapBridge Now!
- Supplied Accessories
- Parts & Controls
- Introduction
- First Steps
- Connecting Using SnapBridge
- Tutorial
- Basic Photography and Playback
- Matching Settings to the Subject or Situation (Scene Mode)
- Special Effects
- P, S, A, and M Modes
- User Settings: U1 and U2 Modes
- Release Mode
- Image Recording Options
- Focus
- ISO Sensitivity
- Exposure
- White Balance
- Image Enhancement
- Flash Photography
- Remote Control Photography
- Recording and Viewing Movies
- Other Shooting Options
- More on Playback
- Menu List
- Technical Notes
- Troubleshooting
- Specs
- Index
- Menu Guide
- Table of Contents
- Menu Guide
- Defaults
- The Playback Menu: Managing Images
- The Photo Shooting Menu: Shooting Options
- Reset Photo Shooting Menu
- Storage Folder
- File Naming
- Flash Control
- Choose Image Area
- Image Quality
- Image Size
- NEF (RAW) Recording
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Color Space
- Active D-Lighting
- Long Exposure NR (Long Exposure Noise Reduction)
- High ISO NR
- Vignette Control
- Auto Distortion Control
- Flicker Reduction
- Remote Control Mode (ML-L3)
- Auto Bracketing Set
- Multiple Exposure
- HDR (High Dynamic Range)
- Interval Timer Shooting
- The Movie Shooting Menu: Movie Shooting Options
- Reset Movie Shooting Menu
- File Naming
- Choose Image Area
- Frame Size/Frame Rate
- Movie Quality
- Movie File Type
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Active D-Lighting
- High ISO NR
- Flicker Reduction
- Microphone Sensitivity
- Frequency Response
- Wind Noise Reduction
- Electronic VR
- Time-Lapse Movie
- Custom Settings: Fine-Tuning Camera Settings
- The Setup Menu: Camera Setup
- Format Memory Card
- Save User Settings
- Reset User Settings
- Language
- Time Zone and Date
- Monitor Brightness
- Monitor Color Balance
- Virtual Horizon
- Information Display
- Auto Info Display
- Info Display Auto Off
- AF Fine-Tune
- Clean Image Sensor
- Lock Mirror up for Cleaning
- Image Dust Off Ref Photo
- Image Comment
- Copyright Information
- Beep Options
- Touch Controls
- Flash Warning
- HDMI
- Location Data
- Wireless Remote (WR) Options
- Assign Remote (WR) Fn Button
- Airplane Mode
- Connect to Smart Device
- Send to Smart Device (Auto)
- Wi-Fi
- Bluetooth
- Eye-Fi Upload
- Conformity Marking
- Battery Info
- Slot Empty Release Lock
- Save/Load Settings
- Reset All Settings
- Firmware Version
- The Retouch Menu: Creating Retouched Copies
- My Menu/Recent Settings
- Optional Flash Units
- Technical Notes
- SnapBridge Connection Guide (Android)
- SnapBridge Connection Guide (iOS)
- Warranty
48 Menu Guide
A Flicker Reduction in the Photo Shooting Menu
Take a test shot and view the results before taking additional
photographs. Flicker reduction can detect flicker at 100 and 120 Hz
(associated respectively with AC power supplies of 50 and 60 Hz).
Flicker may not be detected or the desired results may not be achieved
with dark backgrounds, bright light sources, or decorative lighting
displays and other non-standard lighting. Depending on the light
source, there may be a slight delay before the shutter is released.
During burst shooting, the frame rate may slow or become erratic; in
addition, the desired results may not be achieved if the frequency of
the power supply changes during shooting.
Flicker detection will not take effect at shutter speeds slower than
1
/
100 s (including Bulb and Time) or when MUP is selected for release
mode or exposure delay mode is on. Flicker reduction is available
during flash photography but can not be used with remote wireless
flash units.