Owner's Manual
Table Of Contents
- User Manual
- Table of Contents
- Get SnapBridge Now!
- Supplied Accessories
- Parts & Controls
- Introduction
- First Steps
- Connecting Using SnapBridge
- Tutorial
- Basic Photography and Playback
- Matching Settings to the Subject or Situation (Scene Mode)
- Special Effects
- P, S, A, and M Modes
- User Settings: U1 and U2 Modes
- Release Mode
- Image Recording Options
- Focus
- ISO Sensitivity
- Exposure
- White Balance
- Image Enhancement
- Flash Photography
- Remote Control Photography
- Recording and Viewing Movies
- Other Shooting Options
- More on Playback
- Menu List
- Technical Notes
- Troubleshooting
- Specs
- Index
- Menu Guide
- Table of Contents
- Menu Guide
- Defaults
- The Playback Menu: Managing Images
- The Photo Shooting Menu: Shooting Options
- Reset Photo Shooting Menu
- Storage Folder
- File Naming
- Flash Control
- Choose Image Area
- Image Quality
- Image Size
- NEF (RAW) Recording
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Color Space
- Active D-Lighting
- Long Exposure NR (Long Exposure Noise Reduction)
- High ISO NR
- Vignette Control
- Auto Distortion Control
- Flicker Reduction
- Remote Control Mode (ML-L3)
- Auto Bracketing Set
- Multiple Exposure
- HDR (High Dynamic Range)
- Interval Timer Shooting
- The Movie Shooting Menu: Movie Shooting Options
- Reset Movie Shooting Menu
- File Naming
- Choose Image Area
- Frame Size/Frame Rate
- Movie Quality
- Movie File Type
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Active D-Lighting
- High ISO NR
- Flicker Reduction
- Microphone Sensitivity
- Frequency Response
- Wind Noise Reduction
- Electronic VR
- Time-Lapse Movie
- Custom Settings: Fine-Tuning Camera Settings
- The Setup Menu: Camera Setup
- Format Memory Card
- Save User Settings
- Reset User Settings
- Language
- Time Zone and Date
- Monitor Brightness
- Monitor Color Balance
- Virtual Horizon
- Information Display
- Auto Info Display
- Info Display Auto Off
- AF Fine-Tune
- Clean Image Sensor
- Lock Mirror up for Cleaning
- Image Dust Off Ref Photo
- Image Comment
- Copyright Information
- Beep Options
- Touch Controls
- Flash Warning
- HDMI
- Location Data
- Wireless Remote (WR) Options
- Assign Remote (WR) Fn Button
- Airplane Mode
- Connect to Smart Device
- Send to Smart Device (Auto)
- Wi-Fi
- Bluetooth
- Eye-Fi Upload
- Conformity Marking
- Battery Info
- Slot Empty Release Lock
- Save/Load Settings
- Reset All Settings
- Firmware Version
- The Retouch Menu: Creating Retouched Copies
- My Menu/Recent Settings
- Optional Flash Units
- Technical Notes
- SnapBridge Connection Guide (Android)
- SnapBridge Connection Guide (iOS)
- Warranty
137Menu Guide
7 Clean the sensor.
Remove any dust and lint from the
sensor with a blower. Do not use a
blower-brush, as the bristles could
damage the sensor. Dirt that can not
be removed with a blower can only be
removed by Nikon-authorized service
personnel. Under no circumstances should you touch or wipe
the sensor.
8 Turn the camera off.
The mirror will return to the down position and the shutter
curtain will close. Replace the lens or body cap.
A Use a Reliable Power Source
The shutter curtain is delicate and easily damaged. If the camera
powers off while the mirror is raised, the curtain will close
automatically. To prevent damage to the curtain, observe the
following precautions:
• Do not turn the camera off or remove or disconnect the power source
while the mirror is raised.
• If the battery runs low while the mirror is raised, a beep will sound
and the self-timer lamp will flash to warn that the shutter curtain will
close and the mirror will be lowered after about two minutes. End
cleaning or inspection immediately.