Owner's Manual
Table Of Contents
- User Manual
- Table of Contents
- Get SnapBridge Now!
- Supplied Accessories
- Parts & Controls
- Introduction
- First Steps
- Connecting Using SnapBridge
- Tutorial
- Basic Photography and Playback
- Matching Settings to the Subject or Situation (Scene Mode)
- Special Effects
- P, S, A, and M Modes
- User Settings: U1 and U2 Modes
- Release Mode
- Image Recording Options
- Focus
- ISO Sensitivity
- Exposure
- White Balance
- Image Enhancement
- Flash Photography
- Remote Control Photography
- Recording and Viewing Movies
- Other Shooting Options
- More on Playback
- Menu List
- Technical Notes
- Troubleshooting
- Specs
- Index
- Menu Guide
- Table of Contents
- Menu Guide
- Defaults
- The Playback Menu: Managing Images
- The Photo Shooting Menu: Shooting Options
- Reset Photo Shooting Menu
- Storage Folder
- File Naming
- Flash Control
- Choose Image Area
- Image Quality
- Image Size
- NEF (RAW) Recording
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Color Space
- Active D-Lighting
- Long Exposure NR (Long Exposure Noise Reduction)
- High ISO NR
- Vignette Control
- Auto Distortion Control
- Flicker Reduction
- Remote Control Mode (ML-L3)
- Auto Bracketing Set
- Multiple Exposure
- HDR (High Dynamic Range)
- Interval Timer Shooting
- The Movie Shooting Menu: Movie Shooting Options
- Reset Movie Shooting Menu
- File Naming
- Choose Image Area
- Frame Size/Frame Rate
- Movie Quality
- Movie File Type
- ISO Sensitivity Settings
- White Balance
- Set Picture Control
- Manage Picture Control
- Active D-Lighting
- High ISO NR
- Flicker Reduction
- Microphone Sensitivity
- Frequency Response
- Wind Noise Reduction
- Electronic VR
- Time-Lapse Movie
- Custom Settings: Fine-Tuning Camera Settings
- The Setup Menu: Camera Setup
- Format Memory Card
- Save User Settings
- Reset User Settings
- Language
- Time Zone and Date
- Monitor Brightness
- Monitor Color Balance
- Virtual Horizon
- Information Display
- Auto Info Display
- Info Display Auto Off
- AF Fine-Tune
- Clean Image Sensor
- Lock Mirror up for Cleaning
- Image Dust Off Ref Photo
- Image Comment
- Copyright Information
- Beep Options
- Touch Controls
- Flash Warning
- HDMI
- Location Data
- Wireless Remote (WR) Options
- Assign Remote (WR) Fn Button
- Airplane Mode
- Connect to Smart Device
- Send to Smart Device (Auto)
- Wi-Fi
- Bluetooth
- Eye-Fi Upload
- Conformity Marking
- Battery Info
- Slot Empty Release Lock
- Save/Load Settings
- Reset All Settings
- Firmware Version
- The Retouch Menu: Creating Retouched Copies
- My Menu/Recent Settings
- Optional Flash Units
- Technical Notes
- SnapBridge Connection Guide (Android)
- SnapBridge Connection Guide (iOS)
- Warranty
191Optional Flash Units
4 C: Choose the flash control mode.
Choose the flash control mode and
flash level for the master flash and the
flash units in each group:
• TTL: i-TTL flash control.
• qA: Auto aperture (available only
with compatible flash units; note
that the built-in flash and SB-500 are not compatible with
auto aperture).
• M: Choose the flash level manually.
• – – (off): The units do not fire and the flash level can not be
adjusted.
Choose a channel for the master flash. If the remote flash
units include an SB-500, you must choose channel 3, but
otherwise you can choose any channel between 1 and 4.
5 f: Set the channel.
Set the remote flash units to the channel selected in Step 4.
6 f: Group the remote flash units.
Choose a group (A or B) for each remote flash unit. Although
there is no limit on the number of remote flash units that may
be used, the practical maximum is three per group. With
more than this number, the light emitted by the remote flash
units will interfere with performance.