Nikon DIGITAL CAMERA COOLPIX P610 Quick Start Guide _ln_t_ro_d_u_c_ti_on____________________________ 21lm! Parts of the Camera 6 Preparing for Shooting 7 Basic Shooting and Playback Operations 14 Other Functions 22 Technical Notes 26
Introduction To get the most from this Nikon product, be sure to read "For Your Safety" ([D39-41), " Notes About Location Data Functions (GPS/ GLONASS)" ([D43) and "Wi-Fi (Wireless LAN Network)" (CD44), and all other instructions thoroughly and keep them where they will be read by all who use the camera. • If you want to start using the camera right away, see "Preparing for Shooting" ([D7) and "Basic Shooting and Playback Operations" (CD14).
Confirming the Package Contents In the event that any items are missing, please contact the store where you purchased the camera. D D COOLPIX P61 0 Digital Camera Rechargeable Li-ion Battery EN-EL23 D Camera Strap D D Charging AC Adapter D Lens Cap LC-CP29 (with cord) USB Cable UC-E21 EH-71 P* D Quick Start Guide (this manual) · D Warranty * A plug adapter is included if the camera was purchased in a country or region that requires a plug adapter.
Use Only Nikon Brand Electronic Accessories Nikon COOLPIX cameras are designed to the highest standards and include complex electronic circuitry. Only Nikon brand electronic accessories (including battery cha rgers, batteries, AC adapters and, USB cables) certified by Nikon sp ecifically for use with this Nikon digital camera are engineered and proven to operate within the operational and safety requirements of this electronic circuitry.
• Items prohibited by law from being copied or reproduced Do not copy or reproduce paper money, coins, securities, government bonds or local government bonds, even if such copies or reproductions are stamped "Sample." The copying or reproduction of paper money, coins, or securities which are circulated in a foreign country is prohibited. Unless the prior permission of the government was obtained, the copying or reproduction of unused postage stamps or post cards issued by the government is prohibited.
Parts of the Camera 1 2 3 6 6 7 18 192021222324 12 Electronic viewfinder 1 Power switch/power-on lamp (charge lamp) 2 Fn (function) button 3 Mode dial 4 Flash 5 N-Mark (NFC antenna) 6 Shutter-release button 7 Zoom control W :wide-angle T : telephoto ~:thumbnail playback q : playback zoom 22 iiiJ (delete) button 8 :0: (snap-back zoom) button 23 ®(apply selection) button 9 Side zoom control 10 ~ (flash pop-up) button 24 Rotary multi selector (multi selector) 11 Diopter adjustm
Pre par ing_for Sho otin g Attach the Lens Cap LC-CP29 to the strap, and then attach the strap to the camera. Attach the strap at two places. ~ LensCap • At times when you are not shooting images, attach the lens cap to the lens to protect it. • Do not attach anything other than the lens cap to the lens.
Battery latch Memory card slot • With the battery's positive and negative terminals oriented correctly, the orange battery latch (@),an d fully insert the battery(@)). • Slide the memory card in until it clicks into place (@). • Be careful not to insert the battery or memory card upside- down or backward, as this could cause a malfunction.
1 With the battery installed, connect the camera to an electrical outlet. Charging AC Adapter Electrical outlet . ..~ ~.. ..· :··. Power-on lamp (charge lamp) USB cable (included) If a plug adapter* is included with your camera, securely connect it to the Charging AC Adapter. Once the two are connected, attempting to forcibly remove the plug adapter could damage the product. * The shape of the plug adapter varies according to the country or region in which the camera was purchased.
~ Notes About the USB Cable • Do not use a USB cable other than the UC-E21. Using a USB cable· other than the UC -E21 could result in overheating, fire or electric shock. • Make sure that the plugs are pro p erly ori ented. Do not in sert or remove the plug s at an angle when connecting or disconnecting them.
Changing the orientation of the monitor is useful when shooting with the camera in a high or a low position, or when taking selfies. For normal shooting, fold the monitor against the camera body with the screen facing out(@). CD When you .are not using or carrying the camera, fold the monitor against the camera body with the screen facing inward to prevent scratches or contamination.
Turn the Camera On and Set the Display Language, Date, and Time When the camera is turned on for the first time, the language-selection screen and the date and time setting screen for the camera clock are displayed. 1 Press the power switch to turn on the camera. • The monitor turns on. • To turn the camera off, press the power switch again. O• ON/ OFF - 2 Use the multi selector .A~ to select the desired language and press the® button. 3 Select Yes and press the® button.
6 Set the date and time, and press the® button. • Use ~ to select a field and then use A 'Y to set the date and time. • Select the minute field and press the ® button to confirm the setting. <0111111 7 When the confirmation dialog is displayed, use select Yes and press the® button. _.~to • When settings are finished, the lens extends. D Changing the Language or the Date and Time Setting ' .
Basic Shooting and Playback Operations 1 Rotate the mode dial to 0. • The camera is set to 0 (auto) mode and general shooting can be performed. • Press the DISP (display) button to switch the information displayed in the monitor during shooting and play back. • Battery level indicator (c:::::ll: The battery level is high. (RJI: The battery level is low. • Number of Exposures Remaining 2 Battery level indicator exposures remaining Hold the camera steady.
3 Frame the picture. • Move the zoom control or the side zoom control to change the zoom lens position. • When the subject is lost at the telephoto zoom position, press the :0: (snapback zoom) button to temporarily widen the angle of view so that you can frame the subject more easily. Zoom out :0: button Zoom in Zoom out 4 Press the shutter-release button halfway. • When the subject is in focus, the focus area or focus indicator is displayed in green.
~ Notes About Saving Images or Movi~s The indicator showing the number of exposures remaining or the indicator showing the remaining recording time flashes while images or movies are being saved. Do not open the battery-chamber/memory card slot cover or remove the battery or memory card while an indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the memory card.
Switching Between the Monitor and Viewfinder You can use the viewfinder when bright light under the open sky makes it difficult to see the monitor. • When you bring your face close to the viewfinder, the eye sensor responds to it and the viewfinder turns on while the monitor turns off (default setting). • You can also press the IDI button to switch the display between the monitor and viewfinder.
1 Press the~ (playback) button to enter playback mode. • If you press and hold down the [E button while the camera is turned off, the camera turns on in playback mode. 2 Use the multi selector to select an image to display. • Press and hold down ..6. T ......... to scroll Display the previous image through the images quickly. • Images can also be selected by rotating the multi selector.
1 Press the 1ifl (delete) button to delete the image currently displayed in the monitor. 2 Use the multi selector .._ T to select the desired deletion method and press the ® button. • To exit without deleting, press the MENU button. 3 Select Yes and press the® button. • Deleted images cannot be recovered.
You can change to the following shooting modes by rotating the mode dial. • 0 • • • • 20 (Auto) mode Used for general shooting. SCENE,~, ll), (jji (Scene) modes Camera settings are optimized according to the scene that you select. - SCENE: Press the MENU button and select a scene. When using Scene auto selector, the camera automatically recognizes the shooting scene when you frame a picture, making it easier to take pictures in accordance with t he scene.
When the shooting screen is displayed, you can press the multi selector_.(~)
Other Functions The settings such as image quality can be also set by pressing the Fn (function) button instead of displaying the corresponding menu by pressing the MENU (menu) button. • This function can be used when the shooting mode is P, S, A, M or U. You can set the menus listed below by pressing the MENU (menu) button. · 0, SCENE~, liL ril, EFFECTS, P, S, A, M, U Shooting menu Available by pressing the MENU button when the shooting screen is displayed.
1 Press the MENU (menu) button. • The menu is displayed. 2 Press the multi selector ~. • The current menu icon is displayed in yellow. Menu icons 3 Select a menu icon and press the® button. • The menu options become selectable. 4 Select a menu option and press the® button. • Certain menu options cannot be set depending on the current shooting mode or the state of the camera. • Items can also be selected by rotating the multi selector. 5 p "JP Tnne zone and date Slot empty relt•.
When Record location data in Location data options of the.~ (location data options) menu ([JJ22) is set to On, the camera starts receiving signals from the positioning satellites. Location data reception can be checked on the shooting screen. • ~§ or ~B: Signals are being received from four or more satellites, or from three satellites, and positioning is being performed. • ~:Signals are being received, but positioning is not possible. • Pi: Signals are not received.
You can perform the followi ng functio ns if you install the dedica ted softwa re "Wireless Mobile Utilitl on your smart device that runs on Androi d OS or iOS, and conne ct it to the camera. Take Photos You can use a smart device to remote ly release the camera shutter and save images to the smart device. • Operat ions cannot be perform ed on the camera during remote contro l operat ion. .
Technical Notes Observ e the precau tions describ ed below in additio n to the warnin gs in "For Your Safety" ([D39- 41) when using or storing the device . The Camera Do Not Appl y Strong Impa ct to the Camera n, The produc t may malfun ction if subjected to strong shock or vibration . In additio do not touch or apply force to the lens or lens cover. Keep Dry The device will be damaged if immersed in water or subjected to high humidi ty.
Notes About the Monito r • Monitors and electronic viewfinders are constructe d with extremely high precision; at least 99.99% of pixels are effective, with no more than 0.01 o/o being missing or defective. Hence while these displays may contain pixels that are always lit (white, red, blue, or green) or always off (black), this is not a malfunctio n and has no effect on images recorded with the device. • Images· in the monitor may be difficult to see under bright lighting.
Using the Battery When Cold On cold days, the capacity of batteries tends to decrease. If an exhausted battery is used at a low temperature, the camera may not turn on. Keep spare batteries in a warm place and exchange as necessary. Once warmed, a cold battery may recover some of its charge. Batter y Terminals Dirt on the battery terminals may prevent the camera from function ing. Should the battery terminal s become dirty, wipe them off with a clean, dry cloth before use.
Cleaning Do not use alcohol, thinner, or other volatile chemicals. Avoid touching glass parts with your fingers. Remove dust or lint with a blower (typically a small device with a rubber bulb attached to one end that is pumped to produce a stream of air out the other end). To remove fingerprints or other stains that cannot be removed with a blower, wipe the lens with a soft cloth, using a spiral motion that starts at the center of the lens and working toward the edges.
If the camera fails to functio n as expect ed, check the list of comm on proble ms below before consul ting your retailer or Nikon- author ized service represe ntative . Also, refer to the Reference Manua l (PDF format ) for further details on how to use this camera ([I)2). ' Problem .. ' Cause/Solution '. ·,. CD • Wait for recording to end . • If the problem persists, turn the camera off.
Approved Memory Cards The following Secure Digital (SO) memory cards have been tested and approved for use in this camera. • Memory cards with an SO Speed Class rating of 6 or faster are recommended for recording movies. When using a memory card with a lower Speed Class rating, movie recording may stop unexpectedly. ..,,.
A VC Patent Portfol io License This product is licensed under the AVC Patent Portfolio License for the personal and non-com mercial use of a consume r to (i) encode video in complian ce with the AVC standard ("AVC video") and/or (ii) decode AVC video that wa s encoded by a consume r engaged in a personal and non-com mercial activity and/or was obtained from a video provider licensed to provide AVC video. No license is granted or shall be implied for any other use.
The location name data that is stored in this digital camera ("Data") is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and condition s which are agreed to by you, on the one hand, and Nikon Corporatio n ("Nikon") and its licensors (including their licensors and suppliers) on the other hand. Terms and Condition s Personal Use Only.
Disclaimer of Liability: NIKON AND ITS LICENSORS (INCLUDING THEIR LICENSORS AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU : IN RESPECT OF ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OF THE NATURE OF THE CAUSE OF THE CLAIM, DEMAND OR ACTION ALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT, WHICH MAY RESULT FROM THE USE OR POSSESSION OF THE INFORMATION; OR FOR ANY LOSS OF PROFIT, REVENUE, CONTRACTS OR SAVINGS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF YOUR US
Governm ent End Users. If the Data supplied by HERE is being acquired by or on behalf of the United States governme nt or any other entity seeking or applying rights similar to those customari ly claimed by the United States governme nt, the Data is a "commerc ial item" as that term is defined at 48 C.F.R. ("FAR") 2.
Notices related to licensed softwa re copyrig ht holders. • Location name data for Japan © 2013 ZENRIN CO., LTD. All rights reserved. This service uses POl data of ZENRIN CO., LTD. "ZENRIN" is a registered trademark of ZENRIN CO., LTD. • Location name data except for Japan © 1987-2013 HERE All rights reserved.
Italy: La Banca Dati ltaliana estata prodotta usando quale riferimento anche cartografia numerica ed al tratto prodotta e fornita dalla Regione Toscana. Contains data from Trasporto Passeggeri Emilia-Romagna- S.p.A. Includes content of Comune di Bologna licensed under http://creativecommons.org/licenses/by/ 3.0/legalcode and updated by licensee July 1, 2013. Includes content of Comune di Cesena licensed under http://creativecommons.org/licenses/by/ 3.0/legalcode and updated by licensee July 1, 2013.
Canada: This data includes information taken with permission from Canadian authorities, including © Her Majesty,© Queen's Printer for Ontario, © Canada Post, GeoBase®, ©Department of Natural Resources Canada. All rights reserved . Mexico: Fuente: INEGI (lnstituto Nacional de Estadfstica y Geograffa.) United States: ©United States Postal Service® 2013. Prices are not established, controlled or approved by the United States Postal Service®.
To prevent damage to your Nikon product or injury to yourself or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will read them. The consequences that could result from failure to observe the precautions listed in this section are indicated by the following symbol : ..... ~ This icon marks warnings, information that should be read before using this Nikon product, to prevent possible injury.
A Do not leave the product where it will be exposed to extremely high temperatures, such as in an enclosed automobile or in direct sunlight Failure to observe this precaution could cause damage or fire. A Observe caution when handling the battery The battery may leak, overheat, or explode if improperly handled. Observe the following precautions when handling the battery for use in this product: • Before replacing the battery, turn the product off.
• Do not handle the plug or Charging AC Adapter with wet hands. Failure to observe this precaution could result in electric shock. • Do not use with travel converters or adapters designed to convert from one voltage to another or with DC-to-AC inverters. Failure to observe this precaution could damage the product or cause overheating or fire.
Notices for Customers in the U.S.A. IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONS. DANGER -TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet if needed. The power supply unit is intended to be correctly orientated in a vertical or floor mount position.
Notice for Customers in the State of California WARNING Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Nikon Inc., i 300 Walt Whitman Road, Melville, New York 11747-3064, U.S.
eusing the camera overseas • Before taking the camera with location data functions overseas for travel, consult your travel agency or embassy of the country you are visiting to confirm whether there is any restriction on use. For example, you cannot record location data logs. without permission from the government in China. Set Record location data to Off. • The location data may not function properly in China and on the borders between China and neighboring countries (as of December 2014).
FCC/IC RF Exposure Statement This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION.
NIKON CORPORATION © 2015 Nikon Corporation Printed in China CE: FX4L01 (30) 6MN50430-0 1
DIGITAL CAMERA Reference Manual En
Introduction Table of Contents ii xiv Parts of the Camera 1 Preparing for Shooting 9 Basic Shooting and Playback Operations 16 Shooting Features 26 Functions That Can Be Set with the d (Menu) Button 49 Using Location Data Functions 59 Using the Wi-Fi (Wireless LAN) Function 60 Connecting the Camera to a TV, Printer, or Computer 61 Reference Section E1 Technical Notes and Index F1 i
Introduction Read This First Introduction To get the most from this Nikon product, be sure to read “For Your Safety” (Avi-viii), “ Notes About Location Data Functions (GPS/ GLONASS)” (Axi) and “Wi-Fi (Wireless LAN Network)” (Axii), and all other instructions thoroughly and keep them where they will be read by all who use the camera. • If you want to start using the camera right away, see “Preparing for Shooting” (A9) and “Basic Shooting and Playback Operations” (A16).
Information and Precautions Life-Long Learning Introduction As part of Nikon’s “Life-Long Learning” commitment to ongoing product support and education, continually updated information is available online at the following websites: • For users in the U.S.A.: http://www.nikonusa.com/ • For users in Europe and Africa: http://www.europe-nikon.com/support/ • For users in Asia, Oceania, and the Middle East: http://www.nikon-asia.
About the Manuals Introduction • No part of the manuals included with this product may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without Nikon’s prior written permission. • Illustrations and monitor content shown in this manual may differ from the actual product. • Nikon reserves the right to change the specifications of the hardware and software described in these manuals at any time and without prior notice.
Disposing of Data Storage Devices Introduction Please note that deleting images or formatting data storage devices such as memory cards does not completely erase the original image data. Deleted files can sometimes be recovered from discarded storage devices using commercially available software, potentially resulting in the malicious use of personal image data. Ensuring the privacy of such data is the user’s responsibility.
For Your Safety Introduction To prevent damage to your Nikon product or injury to yourself or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where all those who use the product will read them.
Do not leave the product where it will be exposed to extremely high temperatures, such as in an enclosed automobile or in direct sunlight Failure to observe this precaution could cause damage or fire. Introduction Observe caution when handling the battery The battery may leak, overheat, or explode if improperly handled. Observe the following precautions when handling the battery for use in this product: • Before replacing the battery, turn the product off.
Introduction • Do not damage, modify, forcibly tug or bend the USB cable, place it under heavy objects, or expose it to heat or flames. Should the insulation be damaged and the wires become exposed, take it to a Nikon-authorized service representative for inspection. Failure to observe these precautions could result in fire or electric shock. • Do not handle the plug or Charging AC Adapter with wet hands. Failure to observe this precaution could result in electric shock.
Notices Notices for Customers in the U.S.A. DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet if needed. The power supply unit is intended to be correctly orientated in a vertical or floor mount position. Introduction IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS.
Notice for Customers in the State of California Introduction WARNING Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A. Tel: 631-547-4200 Notice for Customers in Canada CAN ICES-3 B / NMB-3 B Notices for Customers in Europe CAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
Notes About Location Data Functions (GPS/GLONASS) Introduction bLocation name data of this camera Before using the location data functions, make sure to read “USER LICENSE AGREEMENT FOR LOCATION NAME DATA” (F22) and agree to the terms. • The location name information (Points of Interest: POI) are as of April 2014. The location name information will not be updated. • Use the location name information only as a guide.
Wi-Fi (Wireless LAN Network) Introduction This product is controlled by the United States Export Administration Regulations, and you are required to obtain permission from the United States government if you export or re-export this product to any country to which the United States embargoes goods. The following countries were subject to embargo: Cuba, Iran, North Korea, Sudan, and Syria.
COOLPIX P610, which is equipped with a DW092 (FCC ID:EW4DW092/IC ID:4634A-3149EC) Wireless LAN Module, has been tested and found to comply with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Please refer to the SAR test report that was uploaded to FCC website.
Table of Contents Introduction ................................................................................................................ ii Table of Contents Read This First ............................................................................................................................ ii Other Information........................................................................................................................................ ii Information and Precautions ................
Shooting Features................................................................................................... 26 Table of Contents A (Auto) Mode ....................................................................................................................... 26 Scene Mode (Shooting Suited to Scenes)...................................................................... 27 Special Effects Mode (Applying Effects When Shooting).........................................
Reference Section .............................................................................................. E1 Table of Contents xvi Hints and Notes About the Scene Mode................................................................... E3 Shooting with Easy Panorama................................................................................................. E10 Playback with Easy Panorama..................................................................................................
Table of Contents Connecting the Camera to a Printer (Direct Print).............................................. E49 Connecting the Camera to a Printer.................................................................................... E49 Printing Images One at a Time ................................................................................................ E50 Printing Multiple Images .............................................................................................................
Table of Contents xviii The Wi-Fi Options Menu............................................................................................... E91 Operating the Text Input Keyboard ..................................................................................... E92 The Location Data Options Menu............................................................................. E93 Location Data Options...........................................................................................................
Technical Notes and Index............................................................................... F1 Table of Contents Caring for the Product ...................................................................................................... F2 The Camera............................................................................................................................................... F2 The Battery ......................................................................................
t xx
Parts of the Camera The Camera Body Flash raised 1 2 3 4 5 1 6 Parts of the Camera 7 8 9 10 11 12 13 14 15 16 1 Eyelet for camera strap ....................... 9 11 N-Mark (NFC antenna).............E46 2 Power switch/power-on lamp (charge lamp) ..........................11, 14, 18 12 Power connector cover (for optional AC adapter)............. E115 3 w (function) button ... 45, E117 13 4 Mode dial .......................................... 16, 24 Shutter-release button ................
1 2 3 4 5 6 7 8 9 10 11 19 Parts of the Camera 12 13 14 15 16 17 18 Command dial .........................30, 32, E117, E119 1 p (snap-back zoom) button ......21 11 2 Side zoom control ...............................20 f : wide-angle...........................20 g : telephoto ..............................20 12 Monitor ..................................................4, 13 3 Speaker.......................................57, E36 14 c (playback) button ......................
The Monitor The information that is displayed in the monitor during shooting and playback changes depending on the camera’s settings and state of use. Switching the Information Displayed in the Monitor (s Button) To switch the information displayed in the monitor during shooting and playback, press the s (display) button. Parts of the Camera For Shooting 1/250 F5.6 25m 0s 840 Show information Display the image and the shooting information. C 1/250 F5.
For Shooting 3 7 9 2 5 1 4 Parts of the Camera 10 120 11 6 12 1000mm 1000 mm 13 +1.0 +1.0 3200 1/250 F5.6 10m 0 s 9999 21 20 1 Shooting mode....................................24 2 Flash mode .............................................36 3 Focus mode............................................40 4 Zoom indicator.............................20, 41 5 Focus indicator .....................................17 6 Zoom memory .....................................
43 40 2 10 1.0 0.3 42 41 0.7 39 38 36 37 120 60 35 10 120 33 32 31 30 29 28 27 26 25 22 Aperture value......................................30 23 Shutter speed........................................30 24 ISO sensitivity ........................................52 Charging AC adapter 25 connection indicator 26 Battery level indicator ......................16 27 “Date not set” indicator...... 57, F8 28 Date stamp .............................................57 29 Travel destination icon ........
1/250 Parts of the Camera 1 1/250 7 6 2 F5.6 3 4 5 10m 0 s 9999 F5.6 1/250 9 8 1 Focus area (target finding AF) ............................................... 45, 52, E18 2 Focus area (center/manual) ............................... 27, 28, 45, 52, E21 3 Focus area (face detection, pet detection) ..........................39, 45, 52, E8, E19 4 Focus area (subject tracking) ............................................... 45, 52, E74 5 Spot metering area............................
For Playback 1 2 3 45 6 7 9999/9999 25 9999/9999 1m 0s 8 9 10 11 24 23 Demo mode 12 13 20 22 19 18 21 14 15 16 17 1 Protect icon............................................ 55 14 Movie options ...................................... 54 15 Easy panorama indicator.......E12 2 Sequence display (when Individual pictures is selected) ........................................................56, E90 3 Skin softening icon............................ 55 4 Filter effects icon.......................
Tone level information display You can check for loss of contrast detail in highlights and shadows from the histogram that is displayed, or the flashing display for each tone level. These provide guidelines when adjusting the image brightness with functions such as exposure compensation. 4/132 Parts of the Camera 14 13 12 11 10 2 2 3 4 5 100 F5.6 +1.0 0112.JPG 15/11/2015 15:30:59 9 1 8 1/250 8 1 6 7 Current image number/ total number of images 8 Time of recording ..........................
Preparing for Shooting How to Attach the Camera Strap and Lens Cap Attach the Lens Cap LC-CP29 to the strap, and then attach the strap to the camera. Preparing for Shooting Attach the strap at two places. B Lens Cap • At times when you are not shooting images, attach the lens cap to the lens to protect it. • Do not attach anything other than the lens cap to the lens.
Insert the Battery and Memory Card Battery latch Memory card slot Preparing for Shooting • With the battery’s positive and negative terminals oriented correctly, move the orange battery latch (3), and fully insert the battery (4). • Slide the memory card in until it clicks into place (5). • Be careful not to insert the battery or memory card upside-down or backward, as this could cause a malfunction.
Charge the Battery 1 With the battery installed, connect the camera to an electrical outlet. Charging AC Adapter Electrical outlet USB cable (included) If a plug adapter* is included with your camera, securely connect it to the Charging AC Adapter. Once the two are connected, attempting to forcibly remove the plug adapter could damage the product. * The shape of the plug adapter varies according to the country or region in which the camera was purchased.
B Notes About the USB Cable • Do not use a USB cable other than the UC-E21. Using a USB cable other than the UC-E21 could result in overheating, fire or electric shock. • Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them.
Opening and Adjusting the Angle of the Monitor Changing the orientation of the monitor is useful when shooting with the camera in a high or a low position, or when taking selfies. For normal shooting, fold the monitor against the camera body with the screen facing out (3). B Preparing for Shooting When you are not using or carrying the camera, fold the monitor against the camera body with the screen facing inward to prevent scratches or contamination.
Turn the Camera On and Set the Display Language, Date, and Time When the camera is turned on for the first time, the language-selection screen and the date and time setting screen for the camera clock are displayed. 1 Press the power switch to turn on the camera. • The monitor turns on. • To turn the camera off, press the power switch again. Preparing for Shooting 2 Use the multi selector HI to select the desired language and press the k button.
6 Set the date and time, and press the k button. • Use J K to select a field and then use HI to set the date and time. • Select the minute field and press the k button to confirm the setting. Date and time D M Y h m 15 11 2015 15 10 Edit 7 When the confirmation dialog is displayed, use HI to select Yes and press the k button. • When settings are finished, the lens extends.
Basic Shooting and Playback Operations Shooting with A (Auto) Mode 1 Basic Shooting and Playback Operations 16 Rotate the mode dial to A. • The camera is set to A (auto) mode and general shooting can be performed. • Press the s (display) button to switch the information displayed in the monitor during shooting and play back. • Battery level indicator b: The battery level is high. B: The battery level is low. 1/250 Battery level indicator 2 F5.
3 Frame the picture. • Move the zoom control or the side zoom control to change the zoom lens position. • When the subject is lost at the telephoto zoom position, press the p (snapback zoom) button to temporarily widen the angle of view so that you can frame the subject more easily. Zoom out Zoom in p button Zoom in Zoom out Basic Shooting and Playback Operations 4 Press the shutter-release button halfway. • When the subject is in focus, the focus area or focus indicator is displayed in green.
B Notes About Saving Images or Movies The indicator showing the number of exposures remaining or the indicator showing the remaining recording time flashes while images or movies are being saved. Do not open the battery-chamber/memory card slot cover or remove the battery or memory card while an indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the memory card.
Switching Between the Monitor and Viewfinder You can use the viewfinder when bright light under the open sky makes it difficult to see the monitor. • When you bring your face close to the viewfinder, the eye sensor responds to it and the viewfinder turns on while the monitor turns off (default setting). • You can also press the x button to switch the display between the monitor and viewfinder.
Using the Zoom Basic Shooting and Playback Operations 20 Zoom out When you move the zoom control, the zoom lens position changes. • To zoom in: Move toward g • To zoom out: Move toward f • Rotating the zoom control all the way in either direction adjusts the zoom quickly. • The zoom can also be operated by moving the side zoom control toward g or f. The function of the side zoom control can be set in the Assign side zoom control in the setup menu (A57).
Using the Snap-back Zoom When the subject is lost at the telephoto zoom position, press the p (snap-back zoom) button to temporarily widen the angle of view so that you can frame the subject more easily. • While pressing the p button, frame the subject inside the framing border of the shooting screen. To widen the angle of view further, move the zoom control toward f while pressing the p button. • Release the p button to return to the original zoom position.
Play Back Images 1 Press the c (playback) button to enter playback mode. • If you press and hold down the c button while the camera is turned off, the camera turns on in playback mode. 2 Use the multi selector to select an image to display. Basic Shooting and Playback Operations • Press and hold down HIJK to scroll through the images quickly. • Images can also be selected by rotating the multi selector.
Delete Images 1 Press the l (delete) button to delete the image currently displayed in the monitor. 2 Use the multi selector HI to select the desired deletion method and press the k button. • To exit without deleting, press the d button. • When Erase selected images is selected, see “The Image Selection Screen” (A56). Select Yes and press the k button. • Deleted images cannot be recovered.
Changing the Shooting Mode You can change to the following shooting modes by rotating the mode dial. Basic Shooting and Playback Operations 24 • A (Auto) mode Used for general shooting. • y, X, s, c (Scene) modes Camera settings are optimized according to the scene that you select. - y: Press the d button and select a scene. When using Scene auto selector, the camera automatically recognizes the shooting scene when you frame a picture, making it easier to take pictures in accordance with the scene.
Functions That Can Be Set Using the Multi Selector (for Shooting) When the shooting screen is displayed, you can press the multi selector H (m) J (n) I (p) K (o) to set the functions described below. Basic Shooting and Playback Operations • m Flash mode When the flash is raised, the flash mode can be set according to shooting conditions. • n Self-timer/Smile timer The self-timer can be selected from 10 seconds or 2 seconds.
Shooting Features A (Auto) Mode Used for general shooting. • The camera detects the main subject and focuses on it (target finding AF). If a human face is detected, the camera automatically sets focus priority on it. • See “Focusing” (E18) for more information.
Scene Mode (Shooting Suited to Scenes) When a scene is selected, camera settings are automatically optimized for the selected scene. X Night landscape (E3)1, 2, s Night portrait (E3), c Landscape (E4)1, 2 Rotate the mode dial to X, s or c and take pictures. y (Scene) Scene auto selector Portrait Sports Party/indoor Beach Snow Sunset Press the d button to display the scene menu and select one of the following scenes using the multi selector.
Special Effects Mode (Applying Effects When Shooting) Effects can be applied to images during shooting. Image quality Image size Special effects Special effects Soft Nostalgic sepia High-contrast mono. High key Low key Selective color High ISO monochrome Shooting Features 28 Press the d (menu) button to display the special effects menu and select an effect using the multi selector. Type Description Soft* (default setting) Softens the image by adding a slight blur to the entire image.
Type Cross process Description Creates images with an unusual hue by converting a positive color image into negative or negative color image into positive. * Certain Movie options (A54) are not available. • The camera focuses on the area in the center of the frame. The position of the area cannot be moved. • When Selective color or Cross process is selected, rotate the command dial to select the desired color, and press the k button to apply the color.
j, k, l, m Modes (Setting the Exposure for Shooting) Images can be shot with greater control by setting the shooting menu (A51) items in addition to setting the shutter speed or aperture value manually according to shooting conditions and requirements. • The focus area for autofocus differs depending on the setting of AF area mode (A52). • When set to Target finding AF (default setting), the camera detects the main subject and focuses on it.
Exposure The procedure for shooting images at the desired brightness (exposure) by adjusting the shutter speed or aperture value is called “determine exposure.” The sense of dynamism and amount of background defocus in images to be shot vary depending on the combinations of shutter speed and aperture value even if the exposure is the same. Adjusting the Shutter Speed Faster 1/1000 s Slower 1/30 s Adjusting the Aperture Value Shooting Features Larger aperture (Small f-number) f/3.
j (Programmed auto) Use for automatic control of the exposure by the camera. • Different combinations of shutter speed and aperture value can be selected without changing the exposure by rotating the 25m 0s 1/250 F5.6 840 command dial (“flexible program”). While flexible program is in effect, a flexible program mark (A) is displayed next to the mode indicator (j) in the upper left of the monitor.
B Notes About Shooting • When zooming is performed after the exposure is set, exposure combinations or aperture value may be changed. • When the subject is too dark or too bright, it may not be possible to obtain the appropriate exposure. In such cases, the shutter speed indicator or aperture value indicator flashes when the shutter-release button is pressed halfway (except when the m mode is used). Change the shutter speed setting or aperture value.
M (User Settings) Mode Setting combinations that are frequently used for shooting (User settings) can be saved in M. Shooting is possible in j (programmed auto), k (shutterpriority auto), l (aperture-priority auto) or m (manual). Rotate the mode dial to M to retrieve the settings saved in Save user settings. • Frame the subject and shoot with these settings, or change the settings as required.
Saving Settings in M Mode (Save User Settings) The frequently used settings for shooting can be changed and saved in M. 1 Rotate the mode dial to one of j, k, l or m shooting mode that you want to save in M mode. • You can also rotate the mode dial to M to save settings (at the time of purchase, the default setting of j shooting mode is saved). 2 Change to a frequently used combination of shooting settings. • See A34 for settings details.
Flash Mode When the flash is raised, the flash mode can be set according to shooting conditions. 1 Press the m (flash pop-up) button to raise the flash. • When the flash is lowered, flash operation is disabled and S is displayed. Shooting Features 2 Press the multi selector H (m). 3 Select the desired flash mode (A37) and press the k button. Auto • If the setting is not applied by pressing the k button within a few seconds, the selection will be canceled.
Available Flash Modes U Auto The flash fires when necessary, such as in dim lighting. • The flash mode indicator is only displayed immediately after setting in the shooting screen. Auto with red-eye reduction/Red-eye reduction V Reduce red-eye in portraits caused by the flash (A37). • When Red-eye reduction is selected, the flash fires whenever a picture is taken. Fill flash/Standard flash X The flash fires whenever a picture is taken.
Self-timer The camera is equipped with a self-timer that releases the shutter 10 seconds or 2 seconds after you press the shutter-release button. Set Vibration reduction to Off in the setup menu (A57) when using a tripod to stabilize the camera during shooting. 1 Press the multi selector J (n). 2 Select the desired self-timer mode, and press the k button. Self-timer Shooting Features • n10s (10 seconds): Use on important occasions, such as weddings. • n2s (2 seconds): Use to prevent camera shake.
Smile Timer (Shooting Smiling Faces Automatically) When the camera detects a smiling face, you can take a picture automatically without pressing the shutter-release button. • This function can be used when the shooting mode is A (auto), j, k, l, m or M, or Portrait or Night portrait scene mode. 1 Press the multi selector J (n). • Change any flash mode, exposure, or shooting menu settings before pressing J. 2 Select a (smile timer), and press the k button.
Focus Mode Set the focus mode according to the distance to the subject. 1 Press the multi selector I (p). 2 Select the desired focus mode and press the k button. • If the setting is not applied by pressing the k button within a few seconds, the selection will be canceled.
Available Focus Modes Autofocus The camera automatically adjusts the focus according to the distance to the subject. Use when the distance from the subject to the lens is 50 cm (1 ft 8 in.) or more, or 2.0 m (6 ft 7 in.) or more at the maximum telephoto zoom position. • The focus mode icon on the shooting screen is displayed only immediately after the setting is made. D Macro close-up Set when taking close-up pictures.
Using Manual Focus Available when the shooting mode is j, k, l, m or M, special effects mode, or Sports, Fireworks show, Bird-watching or Time-lapse movie (night sky, star trails) scene mode. 1 Press the multi selector I (p), select E (manual focus), and then press the k button. 2 Use the multi selector to adjust the focus while checking the enlarged view. Manual focus 0.3 Shooting Features • An enlarged view of the center area of the image is displayed.
C E (Manual Focus) • The digits displayed for the gauge on the right of the monitor in step 2 serve as a guideline for the distance to a subject that is in focus when the gauge is near the center. • The actual range at which the subject can be in focus varies depending on the aperture value and zoom position. To see whether the subject is in focus, check the image after shooting.
Exposure Compensation (Adjusting Brightness) You can adjust overall image brightness. 1 Press the multi selector K (o). 2 Select a compensation value and press the k button. Shooting Features • To brighten the image, set a positive (+) value. • To darken the image, set a negative (–) value. • The compensation value is applied, even without pressing the k button. C Exposure compensation +2.0 -0.3 -2.
Functions That Can Be Set with the Fn (Function) Button The following functions can be also set by pressing the w (function) button instead of displaying the corresponding menu by pressing the d (menu) button. • This function can be used when the shooting mode is j, k, l, m or M.
Functions That Cannot Be Used Simultaneously When Shooting Some functions cannot be used with other menu settings.
Restricted function Setting Continuous (A52)/Exposure bracketing (A52) Self-timer (A38) Continuous/ Exposure bracketing Smile timer (A39) ISO sensitivity Continuous (A52) Smile timer (A39) Focus mode (A40) AF area mode Picture Control (A51) White balance (A51) • When self-timer is used, a single image is shot even if Continuous H, Continuous L, Pre-shooting cache, or BSS has been set. If Intvl timer shooting is set, shooting finishes automatically after one image is shot.
Restricted function Autofocus mode Setting Smile timer (A39) Focus mode (A40) Active DLighting ISO sensitivity (A52) Multiple exposure Continuous (A52) Exposure bracketing (A52) Shooting Features Monitor settings AF area mode (A52) Date stamp Continuous (A52) Digital zoom Smile timer (A39) Continuous (A52) AF area mode (A52) Zoom memory (A53) Shutter sound Continuous (A52) Exposure bracketing (A52) B Description When smile timer is selected, the autofocus mode operates using the Single AF s
Functions That Can Be Set with the d (Menu) Button You can set the menus listed below by pressing the d (menu) button. 1 Press the d (menu) button. • The menu is displayed. 1/250 F5.6 25m 0s 840 Functions That Can Be Set with the d (Menu) Button • A, y, X, s, c, u, j, k, l, m, M Shooting menu Available by pressing the d button when the shooting screen is displayed. Allows you to change the settings for shooting such as the combination of the image size and image quality.
2 Press the multi selector J. • The current menu icon is displayed in yellow. Shooting menu Image quality Image size Picture Control Custom Picture Control White balance Metering Menu icons 3 Select a menu icon and press the k button. • The menu options become selectable. Set up Time zone and date Slot empty release lock Monitor settings EVF auto toggle Date stamp Vibration reduction 4 Functions That Can Be Set with the d (Menu) Button 50 Select a menu option and press the k button.
The Shooting Menu Enter shooting mode M d button Image quality Image size Picture Control Custom Picture Control White balance Metering Common Options Option Description A Image quality Allows you to set the image quality (compression ratio) of images to be saved. • Default setting: Normal E55 Image size Allows you to set the image size of images to be saved.
Option Functions That Can Be Set with the d (Menu) Button 52 Description A Metering Allows you to set the method that the camera uses to measure the brightness of the subject. • Default setting: Matrix E65 Continuous Allows you to select single or continuous shooting. • Default setting: Single E66 ISO sensitivity Allows you to control the camera’s sensitivity to light. • Default setting: Auto When Auto is selected, E is displayed in the E70 monitor while shooting if ISO sensitivity increases.
Option Description A Reset user settings Allows you to reset the settings saved to mode dial M. 35 Zoom memory When the zoom control is moved, the zoom position (equivalent to focal length/angle of view in 35mm [135] format) is switched to the positions that have been selected by setting the check box to on in this menu option.
The Movie Menu Enter shooting mode M d button M e menu icon M k button Movie options Autofocus mode Electronic VR Wind noise reduction Zoom microphone Frame rate Description A Movie options Select the movie type. Select normal speed to record movies at normal speed, or HS (high speed) to record movies that play in slow or fast motion.
The Playback Menu Press the c button (playback mode) M d button Mark for Wi-Fi upload Quick retouch D-Lighting Skin softening Filter effects Slide show A Mark for Wi-Fi upload1 E87 Quick retouch2 Allows you to create retouched copies in which contrast and saturation have been enhanced. E27 D-Lighting2 Allows you to create copies with enhanced brightness and contrast, brightening dark portions of an image.
1 2 Option Description A Sequence display options Allows you to select whether to display only the key picture for a sequence of images captured continuously or to display the sequence as individual images. • When only the key picture is displayed for a sequence, press the k button to display each image in the sequence. Press the multi selector H to return to the key picture display. E90 Choose key picture1 Allows you to change the key picture for images captured in sequence.
The Setup Menu Press the d button M z menu icon M k button Time zone and date Slot empty release lock Monitor settings EVF auto toggle Date stamp Vibration reduction Option Description Time zone and date Allows you to set the camera clock. A E97 Allows you to set the operation of the shutter button when the memory card is not inserted in the camera. E99 Monitor settings Allows you to adjust post-shooting image review, monitor brightness, and photo information display settings.
Option Functions That Can Be Set with the d (Menu) Button 58 Description A Format card Allows you to format the memory card. E106 Language Allows you to change the camera’s display language. E106 Charge by computer Allows you to set whether or not the battery in the camera is charged when the camera is connected E107 to a computer. Toggle Av/Tv selection Allows you to switch the method for setting the flexible program, shutter speed or aperture value.
Using Location Data Functions When Record location data in Location data options of the z (location data options) menu (E93) is set to On, the camera starts receiving signals from the positioning satellites. 1/250 F5.6 25m 0 s 840 Recording the Shooting Location Data on the Image • When shooting while positioning is being performed, the obtained location data (latitude and longitude) are recorded on the images to be shot.
Using the Wi-Fi (Wireless LAN) Function You can perform the following functions if you install the dedicated software “Wireless Mobile Utility” on your smart device that runs on Android OS or iOS, and connect it to the camera. Take Photos You can save images to a smart device by pressing the shutter-release button of the camera or remotely releasing the camera shutter from the smart device. • Operations cannot be performed on the camera during remote control operation.
Connecting the Camera to a TV, Printer, or Computer You can enhance your enjoyment of images and movies by connecting the camera to a TV, printer, or computer. Micro-USB connector • Before connecting the camera to an external device, make sure the remaining battery level is sufficient and turn the camera off. Before disconnecting, make sure to turn the camera off. • If the AC Adapter EH-67A (available separately) is used, this camera can be powered from an electrical outlet.
Viewing images on a TV Images and movies captured with the camera can be viewed on a TV. Connection method: Connect a commercially available HDMI cable to the TV’s HDMI input jack. Printing images without using a computer If you connect the camera to a PictBridge-compatible printer, you can print images without using a computer. Connection method: Connect the camera directly to the printer’s USB port with the included USB cable.
Reference Section The Reference Section provides detailed information and hints about using the camera. Shooting Hints and Notes About the Scene Mode.................................... E3 Default Settings (Flash, Focus mode, Etc.)...............................E15 Focusing ..............................................................................................E18 The Control Range of the Shutter Speed (j, k, l, m Modes) ........................................................................
Menu The Shooting Menu (The Common Shooting Options) .....E55 The Shooting Menu (j, k, l or m Mode) .............................E57 The Movie Menu ...............................................................................E81 The Playback Menu..........................................................................E87 The Wi-Fi Options Menu ................................................................E91 The Location Data Options Menu ..............................................
Hints and Notes About the Scene Mode X Night landscape • Press the d button to select u Hand-held or w Tripod in Night landscape. • u Hand-held (default setting): - Press the shutter-release button all the way to capture a series of images which are combined into a single image and saved. - Once the shutter-release button is pressed all the way, hold the camera still until a still image is displayed. After taking a picture, do not turn the camera off before the monitor switches to the shooting screen.
c Landscape • Press the d button to select Noise reduction burst or Single shot in Landscape. • Noise reduction burst: This enables you to shoot a sharp landscape with a minimum of noise. - Press the shutter-release button all the way to capture a series of images which are combined into a single image and saved. - Once the shutter-release button is pressed all the way, hold the camera still until a still image is displayed.
y M d Sports • While the shutter-release button is held all the way down, the camera shoots up to about 7 images continuously at a rate of about 7 fps (when image quality is set to Normal and image size is set to i 4608×3456). • The frame rate for continuous shooting may become slow depending on the current image quality setting, image size setting, the memory card used, or shooting condition. • Focus, exposure, and hue are fixed at the values determined with the first image in each series.
y M u Food • The focus mode (A40) setting is changed to D (macro close-up) and the camera automatically zooms to the closest position at which it can focus. • You can adjust hue by using the command dial. The hue setting is saved in the camera’s memory even after the camera is turned off. 1/250 F5.6 • You can move the focus area. Press the k button, use the multi selector HIJK or rotate it to move the focus area, and press the k button to apply the setting.
y M o Backlighting • On the screen displayed when o Backlighting is selected, select On or Off to enable or disable the high dynamic range (HDR) function based on the type of image you want to capture. • Off (default setting): The flash fires to prevent the subject from being hidden in shadow. Shoot images with the flash raised. • On: Use when taking pictures with very bright and dark areas in the same frame. B Notes About HDR Reference Section • Use of a tripod is recommended.
y M O Pet portrait • When you point the camera at a dog or cat, the camera detects the pet’s face and focuses on it. By default, the shutter is automatically released when a dog or cat face is detected (pet portrait auto release). • On the screen displayed when O Pet portrait is selected, select U Single or V Continuous. - U Single: Whenever a dog or cat face is detected, the camera captures 1 image. - V Continuous: Whenever a dog or cat face is detected, the camera captures 3 images continuously.
y M g Moon • You can adjust hue by using the command dial. The hue setting is saved in the camera’s memory even after the camera is turned off. • Adjust the brightness with exposure compensation (A44) according to shooting conditions such as the waxing and waning of the moon and shooting requirements. • At the wide-angle zoom position, the framing border is displayed to indicate the angle of view equivalent to that of 1440 mm lens (in 35mm [135] format).
Shooting with Easy Panorama Rotate the mode dial to y M d button M p Easy panorama M k button 1 Select W Normal (180°) or X Wide (360°) as the shooting range and press the k button. • When the camera is readied in the horizontal position, the image size (width × height) is as follows.
4 Move the camera in one of the four directions until the guide indicator reaches the end. Guide • When the camera detects which direction it is moving in, shooting begins. • Shooting ends when the camera captures the specified shooting range. • Focus and exposure are locked until shooting ends. Example of Camera Movement • Using your body as the axis of rotation, move the camera slowly in an arc, in the direction of the marking (KLJI).
Playback with Easy Panorama Switch to playback mode (A22), display an image captured using easy panorama in fullframe playback mode, and then press the k button to scroll the image in the direction that was used when shooting. • Rotate the multi selector to scroll forward or backward quickly. 4/132 4/132 0004. JPG 2014/05/15 15:30 15/11/2015 Playback controls are displayed in the monitor during playback.
Shooting Time-lapse Movies The camera can automatically capture still images at a specified interval to create time-lapse movies that are approximately 10 seconds long. • When the Frame rate setting of the movie menu is set to 30 fps (30p/ 60p), 300 images are captured and saved with e 1080/30p. When set to 25 fps (25p/50p), 250 images are captured and saved with p 1080/ 25p.
3 4 Stabilize the camera by using a tool such as a tripod. Press the shutter-release button to capture the first image. 25m 0s • Set exposure compensation (A44) before releasing the shutter for the first image. Exposure compensation cannot be changed after the first image is captured. 25m 0s 1/250 F5.6 840 Focus and hue are fixed when the first image is captured. • The shutter is automatically released for the second and subsequent images.
Default Settings (Flash, Focus mode, Etc.) The default settings for each shooting mode are listed below. Flash mode (A36) Self-timer (A38) Focus mode (A40) Exposure compensation (A44) A (auto) U OFF1 A2 0.0 u (special effects) U3 OFF A 0.0 j, k, l, m X OFF1 A 0.0 M (user settings) X OFF1 A 0.0 OFF B4 0.0 A4 0.0 Scene X (night landscape) W4 5 1 V c (landscape) W4 OFF B4 0.0 x (scene auto selector) U6 OFF A4 0.0 b (portrait) V OFF1 A4 0.
Flash mode (A36) Focus mode (A40) Exposure compensation (A44) p (easy panorama) W4 OFF4 A4 0.0 O (pet portrait) W4 Y13 A9 0.0 g (moon) W4 n2s B4 0.0 L (bird-watching) W4 OFF A14 0.0 OFF A/B/ Q15 0.0 i (time-lapse movie) 1 2 3 4 5 Self-timer (A38) W 4 Reference Section Smile timer can also be selected. E (manual focus) cannot be selected. The flash is fixed at W (off) when High ISO monochrome is selected. Cannot be changed. Cannot be changed.
C The Flash Mode Setting The available flash modes differ depending on the shooting mode. Flash mode A y, X, s, c u2 j k l m U Auto w w – – – – Auto with red-eye V reduction Red-eye reduction w w – – – – X Fill flash Standard flash – w 1 – w w w w w – – – – w w w w – – Y Slow sync w w w Z w w w w w w Rear-curtain sync – w – 1 Availability depends on the setting. See “Default Settings (Flash, Focus mode, Etc.)” (E15) for more information.
Focusing The focus area varies depending on the shooting mode. Using Target Finding AF In A (auto) mode, or when AF area mode (A52) in j, k, l, m or M mode is set to Target finding AF, the camera focuses in the manner described below when you press the shutter-release button halfway. • The camera detects the main subject and focuses on it. When the subject is in focus, the focus area is displayed in green. If a human face is detected, the camera automatically sets focus priority on it. 1/250 F5.
Using Face Detection In the following settings, the camera uses face detection to automatically focus on human faces. • s (night portrait), Scene auto selector or Portrait scene mode (A27) • a (smile timer) (A39) 25m 0s • When AF area mode (A52) is set to Face 1/250 F5.6 840 priority If the camera detects more than one face, a double border is displayed around the face that the camera focuses on, and single borders are displayed around the other faces.
Using Skin Softening When the shutter is released while using one of the shooting modes listed below, the camera detects human faces and processes the image to soften facial skin tones (up to 3 faces). • s (night portrait), Scene auto selector or Portrait scene mode (A27) Skin softening can also be applied to saved images (A55). B Notes About Skin Softening • It may take more time than usual to save images after shooting.
Focus Lock Use focus lock to capture creative compositions even when the focus area is set to the center of the frame. 1 Position the subject in the center of the frame and press the shutter-release button halfway. • The camera focuses on the subject and the focus area is displayed in green. • Exposure is also locked. 2 1/250 F5.6 1/250 F5.6 25m 0s 840 Without lifting your finger, recompose the picture. • Make sure to maintain the same distance between the camera and the subject.
The Control Range of the Shutter Speed (j, k, l, m Modes) The control range of the shutter speed differs depending on the zoom position, aperture, or ISO sensitivity setting. Additionally, the control range changes in the following continuous shooting settings.
Playback Zoom Moving the zoom control toward g (i playback zoom) in full-frame playback mode (A22) zooms in on the image. 4/132 0112. JPG 15/11/2015 15:30 Full-frame Playback g (i) g (i) f (h) Displayed area guide Image is zoomed in. C Reference Section • You can change the magnification rate by moving the zoom control toward f (h) or g (i). The zoom can also be adjusted by rotating the command dial. • To view a different area of the image, press the multi selector HIJK.
Thumbnail Playback/Calendar Display Moving the zoom control toward f (h thumbnail playback) in full-frame playback mode (A22) displays images as thumbnails. 4/132 0112.
Viewing and Deleting Images Captured Continuously (Sequence) Viewing Images in a Sequence Images captured continuously are saved as a sequence. The first image of a sequence is used as the key picture to represent the sequence when displayed in full-frame playback mode or thumbnail playback mode (default setting). To display each image in the sequence individually, press the k button. 4/132 0004. JPG 15/11/2015 15:30 After pressing the k button, the operations listed below are available.
Deleting Images in a Sequence When the l (delete) button is pressed for images in a sequence, the images that are deleted vary depending on how the sequences are displayed. • When the key picture is displayed: - Current image: All images in the displayed sequence are deleted. - Erase selected images: When a key picture is selected on the erase selected images screen (A56), all images in that sequence are deleted. - All images: All images on the memory card are deleted.
Quick Retouch: Enhancing Contrast and Saturation Press the c button (playback mode) M Select an image M d button M Quick retouch M k button Use the multi selector HI to select the desired effect level and press the k button. Quick retouch • The edited version is displayed on the right. • To exit without saving the copy, press J.
Skin Softening: Softening Skin Tones Press the c button (playback mode) M Select an image M d button M Skin softening M k button 1 Use the multi selector HI to select the desired effect level and press the k button. Skin softening • To exit without saving the copy, press J. Normal Amount 2 Preview the result and press the k button. • The edited face is zoomed in. • When more than one face has been edited, press JK to switch the face that is displayed.
Filter Effects: Applying Digital Filter Effects Press the c button (playback mode) M Select an image M d button M Filter effects M k button Option Description Selective color Keeps only a selected image color and makes other colors black-and-white. Cross screen Produces star-like rays of light that radiate outward from bright objects such as sunlight reflections and city lights. Suitable for night scenes. Fisheye Creates images that look like they were shot with a fisheye lens.
2 Use HI to select the color to keep and press the k button. 3 Preview the result and press the k button. Selective color Preview • An edited copy is created. • To exit without saving the copy, press J. Back Save Small Picture: Reducing the Size of an Image Press the c button (playback mode) M Select an image M d button M Small picture M k button 1 Reference Section Use the multi selector HI to select the desired copy size and press the k button.
Crop: Creating a Cropped Copy 1 2 Move the zoom control to enlarge the image (E23). Adjust the image so that only the portion that you want to keep is displayed, and then press the d (menu) button. • Move the zoom control toward g (i) or f (h) to adjust the magnification rate. Set a 4.0 magnification rate at which u is displayed. • Use the multi selector HIJK to scroll to the portion of the image that you want to display. 3 Check the image and press the k button.
Recording and Playing Back Movies 1 Display the shooting screen. • Check the remaining amount of movie recording time. 1/250 F5.6 25m 0s 840 Remaining movie recording time 2 Press the b (e movie-record) button to start movie recording. • The camera focuses on the subject in the center of the frame. • Press k button to pause recording, and press k button again to resume recording (except when an HS movie option is selected in Movie options).
Area Captured in Movies • The area that is captured in a movie varies depending on the Movie options or Electronic VR settings in the movie menu. • Press the s button and display the movie frame (A3) to check the range of a movie in a frame before movie recording. Focusing During Movie Recording • The focus can be adjusted during movie recording in the following manner in accordance with the Autofocus mode (A54) setting of the movie menu.
Notes About Movie Recording B Notes About Saving Images or Movies The indicator showing the number of exposures remaining or the indicator showing the remaining recording time flashes while images or movies are being saved. Do not open the battery-chamber/memory card slot cover or remove the battery or memory card while an indicator is flashing. Doing this could result in loss of data, or in damage to the camera or the memory card.
Capturing Still Images While Recording Movies If the shutter-release button is pressed all the way while recording a movie, one frame is saved as a still image. Movie recording continues while the still image is being saved. • A still image can be captured when Q is displayed in the monitor. When f is displayed, a still image cannot be captured. • The image size of the still images to be saved is determined by the type (image size) (E81) of the original movie.
7m 42s Operations During Movie Playback To adjust the volume, move the zoom control while a movie is playing (A1). Rotate the multi selector or the command dial to advance or rewind. 7m 42s Volume indicator Playback controls are displayed in the monitor. The operations described below can be performed by using the multi selector JK to select a control and then pressing the k button. Function Icon When paused Description Rewind A Hold down the k button to rewind the movie.
Editing Movies When editing movies, use a sufficiently charged battery to prevent the camera from turning off during editing. When the battery level indicator is B, movie editing is not possible. Extracting Only the Desired Portion of a Movie The desired portion of a recorded movie can be saved as a separate file. 1 Play back a desired movie and pause at the start point of the portion that you want to extract (E36). 2 Use the multi selector JK to select the I control, and then press the k button.
5 Use HI to select m (save) and press the k button. Save • Follow the instructions on the screen to save the movie. 5m 52s B Notes About Movie Extracting • A movie that was created by editing cannot be edited again. • The actual trimmed portion of a movie may differ slightly from the portion selected using the start and end points. • Movies cannot be trimmed so that they are less than two seconds long.
Recording the Location Data on the Image Press the d button M z menu icon M Location data options M k button Set Time zone and date (E97) correctly before using the location data functions. 1 Set Record location data to On. • After the settings are complete, press the d button or shutter-release button to exit the menu. • To receive signals easily, operate in an openair area. 2 Record location data On Off Check the location data reception on the shooting screen.
B Notes About Location Data Functions Reference Section • Before using the location data functions, read “ Notes About Location Data Functions (GPS/GLONASS)” (Axi). • It takes a few minutes to obtain location data when positioning is performed for the first time or in a situation where positioning cannot be performed for a long period of time, or just after the battery is replaced. Using the latest A-GPS file can shorten the time needed for obtaining the location data (E93).
C Points of Interest (POI) Information • POI information is location name information for Location name information landmarks (facilities) and other details. (POI information) • When Display POI in Points of interest (POI) (E95) of the location data options menu is set to On, the nearest location name information for the current position is displayed during shooting (only when positioning is being performed).
Recording the Log of Movement Information Press the d button M z menu icon M Create log M k button 1 Use the multi selector HI to select Log interval, and press the k button. Create log Start log Log interval End log 2 Select the intervals of log recording, and press the k button. • The default setting is 15 s. Log interval 5s 10 s 15 s 30 s 1 min 3 Select Start log, and press the k button.
B Notes About Log Recording • If the date and time are not set, the log cannot be recorded. • Use a fully charged battery to prevent the camera from turning off during log recording. When the battery power becomes exhausted, log recording ends. • Even when the camera is turned off, log recording is continuously performed until the preset time has elapsed if there is still time remaining for log recording. • Log recording ends due to the operations below even when there is time remaining for log recording.
Ending Log to Save it on Memory Cards After the obtained log is saved to a memory card by using Save log in the location data options menu, view the log with software that can display log data. Press the d button M z menu icon M Create log M k button 1 When log recording is completed, select End log on the screen, and press the k button. • Ending log can also be performed before the preset time elapses. 2 Select Save log, and press the k button. • The log data is saved to a memory card.
Connecting to a Smart Device (Wi-Fi) 1 Press the q (Wi-Fi) button on the camera. • The screen shown on the right is displayed. • If no connection confirmation is received from the smart device within 3 minutes, the message No access. is displayed and the camera returns to the Wi-Fi options screen. • You can also select Connect to smart device in the Wi-Fi options menu to display the screen shown on the right.
B Notes About Shooting • When Wi-Fi is connected, Intvl timer shooting in Continuous cannot be used. • Operations cannot be performed on the camera during remote control operation. The shooting mode is set to A (auto) mode and the focus area is set to the center of the frame, regardless of the camera's settings.
Preselecting Images in the Camera That You Want to Transfer to a Smart Device You can preselect images in the camera that you want to transfer to a smart device. Movies cannot be preselected for transfer. 1 Select images to transfer.
Connecting the Camera to a TV (Playback on a TV) 1 Turn off the camera and connect it to the TV. • Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them. HDMI micro connector (Type D) 2 to HDMI jack Set the TV’s input to external input. • See the documentation provided with your TV for details. 3 Reference Section E48 Press and hold down the c (playback) button to turn on the camera. • Images are displayed on the TV.
Connecting the Camera to a Printer (Direct Print) Users of PictBridge-compatible printers can connect the camera directly to the printer and print images without using a computer. Connecting the Camera to a Printer 1 2 Turn on the printer. Turn off the camera and connect it to the printer using the USB cable. • Make sure that the plugs are properly oriented. Do not insert or remove the plugs at an angle when connecting or disconnecting them. 3 The camera is automatically turned on.
Printing Images One at a Time 1 Use the multi selector JK to select the desired image and press the k button. Print selection 15/11/2015 No. 32 • Move the zoom control toward f (h) to switch to thumbnail playback or g (i) to switch to full-frame playback. 2 Use HI to select Copies and press the k button. • Use HI to set the desired number of copies (up to 9) and press the k button. PictBridge 1 prints Start print Copies Paper size 3 Select Paper size and press the k button.
Printing Multiple Images 1 When the Print selection screen is displayed, press the d (menu) button. 2 Use the multi selector HI to select Paper size and press the k button. Print selection 15/11/2015 No. 32 [ 32] Print menu Print selection Print all images Paper size • Select the desired paper size and press the k button. • To print with the paper size setting configured on the printer, select Default. • The paper size options available on the camera vary depending on the printer that you use.
Print selection Select images (up to 99) and the Print selection number of copies (up to 9) of each. • Use the multi selector JK to select images, and use HI to specify the 1 1 3 number of copies to be printed. • Images selected for printing are indicated by a and the number of Back copies to be printed. To cancel the print selection, set the number of copies to 0. • Move the zoom control toward g (i) to switch to full-frame playback or f (h) to switch to thumbnail playback.
Using ViewNX 2 (Transferring Images to a Computer) Installing ViewNX 2 ViewNX 2 is free software that enables you to transfer images and movies to your computer so that you can view, edit, or share them. To install ViewNX 2, download the ViewNX 2 installer from the website below and follow the onscreen installation instructions. http://nikonimglib.com/nvnx/ For system requirements and other information, see the Nikon website for your region.
If a message is displayed prompting you to choose a program, select Nikon Transfer 2. • When using Windows 7 If the dialog shown at right is displayed, follow the steps below to select Nikon Transfer 2. 1 Under Import pictures and videos, click Change program. A program selection dialog will be displayed; select Import File using Nikon Transfer 2 and click OK. 2 Double-click Import File. If the memory card contains a large number of images, it may take a while for Nikon Transfer 2 to start.
The Shooting Menu (The Common Shooting Options) • See “M (User Settings) Mode” (A34) for information about Save user settings and Reset user settings. Image Quality Enter shooting mode* M d button M shooting mode menu icon M Image quality M k button * The image quality can be set in any shooting mode. The setting is also applied to other shooting modes (except shooting mode M and Easy panorama scene mode). Set the image quality (compression ratio) used when saving images.
Image Size Enter shooting mode* M d button M shooting mode menu icon M Image size M k button * The image size can be set in any shooting mode. The setting is also applied to other shooting modes (except shooting mode M and Easy panorama scene mode). Set the image size (number of pixels) used when saving images. The larger the image size, the larger the size at which it can be printed, but the number of images that can be saved is reduced.
The Shooting Menu (j, k, l or m Mode) Picture Control (COOLPIX Picture Control) Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Picture Control M k button Change the settings for image recording according to the shooting scene or your preferences. Sharpness, contrast and saturation can be adjusted in detail. Description Option Standard processing for balanced results. Recommended for most situations. c Neutral Minimal processing for natural results.
Customizing Existing COOLPIX Picture Controls: Quick Adjust and Manual Adjust COOLPIX Picture Control can be customized using Quick adjust, which allows for balanced adjustment of sharpness, contrast, saturation and other image editing components, or manual adjust, which allows for detailed adjustment of the components individually. 1 Use the multi selector HI to select the desired type of COOLPIX Picture Control and press the k button. • Items can also be selected by rotating the multi selector.
Types of Quick Adjust and Manual Adjust Option Description Image sharpening Controls how much outlines are sharpened during shooting. The higher the number, the sharper the image, and the lower the number, the softer the image. Select A (auto) for automatic adjustment. • Default setting: 3 for Standard or Monochrome, 2 for Neutral and 4 for Vivid Contrast Controls the contrast. Setting to the – side gives the image a softer appearance, and setting to the + side gives it a harder appearance.
Option Toning 3 1 2 3 Description Controls the tint used in monochrome photographs from B&W (black-and-white), Sepia, and Cyanotype (blue-tinted monochrome). Pressing the multi selector I when Sepia or Cyanotype is selected enables you to select a saturation level. Press JK to adjust the saturation. • Default setting: B&W (black-and-white) Quick adjust is not available in Neutral, Monochrome, Custom 1 and Custom 2. The values set manually are disabled if quick adjust is used after manual setting.
Custom Picture Control (COOLPIX Custom Picture Control) Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Custom Picture Control M k button Customize the settings of COOLPIX Picture Control (E58) and register them in Custom 1 or Custom 2 of Picture Control. 1 Use the multi selector HI to select Edit and save, and press the k button. • Select Delete to delete a registered COOLPIX Custom Picture Control.
White Balance (Adjusting Hue) Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M White balance M k button Adjust white balance to suit the light source or weather conditions in order to make the colors in images match what you see with your eyes. Description Option White balance is automatically adjusted. When set to Auto (warm lighting), the images are preserved with warm colors if they are shot under an incandescent light source.
C Color Temperature Color temperature is an objective measure of colors of light sources which are expressed in the unit of absolute temperature (K: Kelvin). Light sources with lower color temperatures appear more reddish, while light sources with higher color temperatures appear more bluish.
Using Preset Manual Use the procedure below to measure the white balance value under the lighting used during shooting. 1 Place a white or gray reference object under the lighting that will be used during shooting. 2 Use the multi selector HI to select Preset manual, and press the k button. • The lens extends to the zoom position for measurement. White balance Auto (normal) Auto (warm lighting) Preset manual Daylight Incandescent Fluorescent Cloudy 3 Select Measure.
Metering Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Metering M k button The process of measuring the brightness of the subject to determine the exposure is known as “metering.” Use this option to set the method of how the camera meters exposure. Option G Matrix (default setting) Description The camera uses a wide area of the screen for metering. Recommended for typical shooting.
Continuous Shooting Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Continuous M k button Option U Single (default setting) Description One image is captured each time the shutter-release button is pressed. Reference Section k Continuous H While the shutter-release button is held all the way down, images are captured continuously.
Option Description Continuous H: 60 fps Each time the shutter-release button is pressed all the way, images are captured at a high speed rate. • The frame rate for continuous shooting is about 60 fps and the maximum number of continuous shots is 60. • Image size is fixed at O 1920×1080. D BSS (Best Shot Selector) While the shutter-release button is held all the way down, the camera captures a series of up to 10 images and automatically saves the sharpest image.
C Pre-shooting Cache When the shutter-release button is pressed halfway or all the way down, images are saved as described below. Press down halfway Press down all the way Images saved before Images saved by pressing all the way pressing all the way • The pre-shooting cache icon (Q) on the shooting screen changes to green while the shutter-release button is pressed halfway.
2 Set the desired interval between each shot. Intvl timer shooting • Use JK to select an item, and use HI to set the time. • Press the k button when setting is complete. m s 00 30 Edit 3 4 Press the d (menu) to display the shooting screen. Press the shutter-release button to shoot the first image. • The shutter is automatically released at the specified interval to shoot subsequent images.
ISO Sensitivity Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M ISO sensitivity M k button A higher ISO sensitivity allows darker subjects to be captured. Additionally, even with subjects of similar brightness, pictures can be taken at faster shutter speeds, and blurring caused by camera shake and subject movement can be reduced. • When a higher ISO sensitivity is set, images may contain noise.
Exposure Bracketing Rotate the mode dial to j, k or l M d button M j, k or l menu icon M Exposure bracketing M k button The exposure (brightness) can be changed automatically during continuous shooting. This is effective for shooting when it is difficult to adjust the picture brightness. Option Description Off (default setting) Exposure bracketing is not performed. ±0.3 When the shutter-release button is pressed all the way, 3 shots are taken in sequence and the camera varies exposure by 0, –0.
AF Area Mode Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M AF area mode M k button Set how the camera selects the focus area for autofocus. Option Description When the camera detects a human face, it focuses on that face. See “Using Face Detection” (E19) for more information.
Option s M Subject tracking Target finding AF (default setting) Description Use this function to take pictures of moving subjects. Register the subject on which the camera focuses. The focus area automatically moves to track the subject. See “Using Subject Tracking” (E74) for more information. End 1/250 F5.6 1/250 F5.6 25m 0s 840 When the camera detects the main subject, it focuses on that subject. See “Using Target Finding AF” (E18).
Using Subject Tracking Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M AF area mode M k button M s Subject tracking M k button M d button 1 Register a subject. • Align the subject that you want to track with the border in the center of the monitor and press the k button. • When the subject is registered, a yellow border (focus area) is displayed around it and the camera begins tracking the subject. • If the subject cannot be registered, the border is displayed in red.
Autofocus Mode Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Autofocus mode M k button Set how the camera focuses when shooting still images. Option Description The camera focuses only when the shutter-release button is pressed halfway. A Single AF B B Full-time AF (default setting) The camera continues focusing even when the shutter-release button is not pressed halfway. The sound of lens drive movement is heard while the camera focuses.
Noise Reduction Filter Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Noise reduction filter M k button Set the strength of the noise reduction function that is normally performed when saving images. Option e High Normal (default setting) M l Low Description Performs noise reduction at a level higher than the standard strength. Performs noise reduction at the standard strength. Performs noise reduction at a level lower than the standard strength.
Multiple Exposure Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Multiple exposure M k button The camera combines two to three images and saves them as a single image. Option Description Multiple exposure mode Shoots images in multiple exposure mode when set to On. • Individual images are also saved. • Default setting: Off Auto gain Set whether or not to automatically adjust the brightness of the image when combining images.
2 Select On, and then press the k button. Multiple exposure mode On Off 3 Press the d (menu) button to display the shooting screen. 4 Press the shutter-release button to shoot the first image. 1/250 5 F5.6 25m 0s 840 Press the shutter-release button to shoot the second image. Reference Section • Frame the picture while looking at the first image displayed translucently. • When shooting the second image, the combined image of the first and second 25m 0s 1/250 F5.
Zoom Memory Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Zoom memory M k button Option Description On When the zoom control is moved, the zoom position (equivalent to focal length/angle of view in 35mm [135] format) is switched to the positions that have been selected by setting the check box to on in this menu option. • Choose the focal length with the multi selector HI, and then press the k button to set the check box to on [w] or off.
Startup Zoom Position Rotate the mode dial to j, k, l, m or M M d button M j, k, l, m or M menu icon M Startup zoom position M k button Set the zoom position (equivalent to focal length/angle of view in 35mm [135] format) for when the camera is turned on. The following settings are available: 24 mm (default setting), 28 mm, 35 mm, 50 mm, 85 mm, 105 mm and 135 mm.
The Movie Menu Movie Options Enter shooting mode M d button M e menu icon M Movie options M k button Select the desired movie option to record. Select normal speed movie options to record at normal speed, or HS movie options (E82) to record in slow or fast motion. The movie options that can be selected vary depending on the Frame rate setting (E86). • Memory cards with an SD Speed Class rating of 6 or faster are recommended for recording movies (F20).
HS Movie Options Recorded movies are played back in fast or slow motion. See “Playing Back in Slow Motion and Fast Motion” (E83). Option Image size Aspect ratio (horizontal to vertical) Description h HS 480/4×* u 640 × 480 4:3 1/4-speed slow motion movies • Max. recording time: 7 minutes 15 seconds (playback time: 29 minutes) i w 1280 × 720 16:9 1/2-speed slow motion movies • Max. recording time: 14 minutes 30 seconds (playback time: 29 minutes) 1920 × 1080 16:9 2× speed fast motion movies • Max.
C Playing Back in Slow Motion and Fast Motion When recording at normal speed: Recording time 10 s Playback time 10 s When recording at h HS 480/4×, or u HS 480/4×: Movies are recorded at 4× normal speed. They are played back in slow motion at 4× slower speed. Recording time 10 s Playback time 40 s Slow motion playback When recording at j HS 1080/0.5×, or x HS 1080/0.5×: Movies are recorded at 1/2 normal speed. They are played back in fast motion at 2× faster speed.
Autofocus Mode Enter shooting mode M d button M e menu icon M Autofocus mode M k button Set how the camera focuses when recording movies. Option A Single AF (default setting) B Full-time AF B Description Focus is locked when movie recording starts. Select this option when the distance between the camera and the subject will remain fairly consistent. The camera focuses continuously. Select this option when the distance between the camera and subject will change significantly during recording.
Electronic VR Enter shooting mode M d button M e menu icon M Electronic VR M k button Set whether or not to perform electronic VR when recording movies. Option Description On (default setting) Performs electronic VR. • The angle of view (i.e., the area seen in the frame) becomes narrower. • When Vibration reduction is set to Normal or Active in the setup menu (A57), optical vibration reduction is performed simultaneously. Off Does not perform electronic VR.
Zoom Microphone Enter shooting mode M d button M e menu icon M Zoom microphone M k button Option Description On (default setting) In accordance with the angle of view, the camera records sounds over a wide area at the wide-angle zoom position, and records sounds in the limited area at the telephoto zoom position. Off Zoom microphone is disabled. B Notes About Zoom Microphone When an HS movie option is selected in Movie options, the setting is fixed at Off.
The Playback Menu See “Editing Images (Still Images)” (E26) for information about image editing functions. Mark for Wi-Fi Upload Press the c button (playback mode) M d button M Mark for Wi-Fi upload M k button Select still images in the camera that you want to transfer to a smart device in advance before transferring them. Movies cannot be selected. On the image selection screen (A56), select or deselect images for the Mark for Wi-Fi upload function.
Slide Show Press the c button (playback mode) M d button M Slide show M k button Play back images one by one in an automated “slide show.” When movie files are played back in the slide show, only the first frame of each movie is displayed. 1 Use the multi selector HI to select Start and press the k button. Slide show Start Frame intvl • The slide show begins.
Protect Press the c button (playback mode) M d button M Protect M k button The camera protects selected images from accidental deletion. Select images to protect or cancel protection from the image selection screen (A56). Note that formatting the memory card permanently deletes all data including protected files (E106). Rotate Image Press the c button (playback mode) M d button M Rotate image M k button Specify the orientation in which saved images are displayed during playback.
Sequence Display Options Press the c button (playback mode) M d button M Sequence display options M k button Select the method used to display images in the sequence (E25). Option Description Individual pictures Displays each image in a sequence individually. F is displayed on the playback screen. Key picture only (default setting) Displays only the key picture for images in a sequence.
The Wi-Fi Options Menu Press the d button M q menu icon M k button Configure the Wi-Fi (wireless LAN) settings to connect the camera and a smart device. Option Connect to smart device Upload from camera Disable Wi-Fi Current settings Restore default settings Reference Section Options Description Select when wirelessly connecting the camera and a smart device. See “Connecting to a Smart Device (Wi-Fi)” (E45) for more information. Select when wirelessly connecting the camera and a smart device.
Operating the Text Input Keyboard Character Input for SSID and Password • Use the multi selector HIJK to select alphanumeric characters. Press the k button to enter the selected character in the text field and move the cursor to the next space. • To move the cursor in the text field, select N or O on the keyboard, and press the k button. • To delete one character, press the l button. • To apply the setting, select P on the keyboard and press the k button.
The Location Data Options Menu Location Data Options Press the d button M z menu icon M Location data options M k button Option Description Record location data When set to On, signals are received from the positioning satellites, and positioning starts (E39). • Default setting: Off Update A-GPS file A memory card is used to update the A-GPS (assist GPS) file. Using the latest A-GPS file can shorten the time needed for obtaining the location data.
Updating the A-GPS File Download the latest A-GPS file from the website below, and use it to update the file. http://nikonimglib.com/agps4/ • The A-GPS file for the COOLPIX P610 is only available from the website above. 1 Download the latest A-GPS file to the computer from the website. 2 Use a card reader or other device to copy the downloaded file to the “NCFL” folder of the memory card. • The “NCFL” folder is located directly under the memory card root directory.
Points of Interest (POI) (Recording and Displaying Location Name Information) Press the d button M z menu icon M Points of interest (POI) M k button Configure the POI (points of interest, location name information) settings. Option Description Display POI Set whether or not to display the location name information on the shooting screen or playback screen (A6, 7). • If Embed POI was set to On when an image was captured, the location name information for the image is displayed on the playback screen.
Set Clock from Satellite Press the d button M z menu icon M Set clock from satellite M k button Signals from the positioning satellites are used to set the date and time of the camera’s internal clock. Check the positioning status before setting the clock using this option. B Notes About Set Clock from Satellite • To set the camera’s internal clock, positioning must have been done successfully (E39).
The Setup Menu Time Zone and Date Press the d button M z menu icon M Time zone and date M k button Set the camera clock. Option Date and time Description • Select a field: Press the multi selector JK. • Edit the date and time: Press HI. Date and time can also be changed by rotating the multi selector or command dial. • Apply the setting: Select the minute field setting and press the k button or K.
2 Select w Home time zone or x Travel destination and press the k button. • The date and time displayed in the monitor changes depending on whether the home time zone or travel destination is selected. 3 Press K. Time zone Home time zone Travel destination London, Casablanca 15/11/2015 15:30 Time zone Home time zone Travel destination London, Casablanca 15/11/2015 15:30 4 Use JK to select the time zone. • Press H to enable daylight saving time function, and W is displayed.
Slot Empty Release Lock Press the d button M z menu icon M Slot empty release lock M k button Set whether or not the shutter can be released when no memory card is inserted in the camera. Option Description Release locked (default setting) Unless a memory card is inserted in the camera, the shutter cannot be released. Enable release Even when no memory card is inserted in the camera, the shutter can be released.
Monitor Settings Press the d button M z menu icon M Monitor settings M k button Option Description Reference Section Image review Set whether or not to display the captured image immediately after shooting. • Default setting: On Monitor options Adjust the monitor brightness and hue. • Use the multi selector HI to adjust brightness, JK to adjust hue and then press the k button. • Default setting: Brightness 3 Hue 0 • Cannot be set when the viewfinder is used.
EVF Auto Toggle (Automatically Switching the Display to the Viewfinder) Press the d button M z menu icon M EVF auto toggle M k button Option Description On (default setting) When you bring your face close to the viewfinder, the eye sensor responds to it and the display is automatically switched from the monitor to viewfinder. Off Even when you bring your face close to the viewfinder, the display is not switched to the viewfinder.
Date Stamp Press the d button M z menu icon M Date stamp M k button The shooting date and time can be stamped on images when shooting. 15.11.2015 Option Description fDate Date is stamped on images. SDate and time Date and time are stamped on images. Off (default setting) Date and time are not stamped on images. B Notes About Date Stamp Reference Section • Stamped dates form a permanent part of image data and cannot be deleted.
Vibration Reduction Press the d button M z menu icon M Vibration reduction M k button Select the vibration reduction setting used when shooting. Select Off when using a tripod to stabilize the camera during shooting. Option Description g Normal (default setting) Compensates camera shake that commonly occurs when shooting at telephoto zoom positions or slow shutter speeds. The camera automatically detects the panning direction and only compensates for vibration caused by camera shake.
AF Assist Press the d button M z menu icon M AF assist M k button Option Description Auto (default setting) The AF-assist illuminator automatically lights up when you press the shutter-release button under dim lighting. The illuminator has a range of about 5.0 m (16 ft) at the maximum wide-angle position and about 5.0 m (16 ft) at the maximum telephoto position. • Note that for some scene modes or focus areas, the AF-assist illuminator may not light. Off The AF-assist illuminator does not light.
Assign Side Zoom Control Press the d button M z menu icon M Assign side zoom control M k button Choose the function to be performed during shooting when the side zoom control is moved. Option Description When shooting, use the side zoom control (A20) to Zoom (default setting) adjust the zoom. Manual focus When the focus mode is set to E (manual focus), use the side zoom control to focus (A42). • Move the side zoom control toward g to focus on distant subjects.
Auto Off Press the d button M z menu icon M Auto off M k button Set the amount of time that elapses before the camera enters standby mode (A18). You can select 30 s, 1 min (default setting), 5 min, or 30 min.
Charge by Computer Press the d button M z menu icon M Charge by computer M k button Option Description a Auto (default setting) When the camera is connected to a computer that is running (A61), the battery inserted into the camera is automatically charged using power supplied by the computer. Off The battery inserted into the camera is not charged when the camera is connected to a computer.
Toggle Av/Tv Selection Press the d button M z menu icon M Toggle Av/Tv selection M k button Switch the method for setting the flexible program, shutter speed or aperture value when shooting mode is set to j, k, l, m or M. Option Description Do not toggle selection Use the command dial to set the flexible program or shutter (default setting) speed, and the multi selector to set the aperture value.
Peaking Press the d button M z menu icon M Peaking M k button Option Description On (default setting) When operating E (manual focus), focusing is assisted by highlighting areas that are in focus in white on the image displayed in the monitor (A42, 43). Off Peaking is disabled. Reset All Press the d button M z menu icon M Reset all M k button When Reset is selected, the camera’s settings are restored to their default values. • Some settings, such as Time zone and date or Language, are not reset.
Error Messages Refer to the table below if an error message is displayed. Display Battery temperature is elevated. The camera will turn off. The camera will turn off to prevent overheating. Cause/Solution The camera turns off automatically. Wait until the battery has cooled before resuming use. The write-protect switch is in the “lock” position. Memory card is write Slide the write-protect switch to the “write” protected. position. This card cannot be used. This card cannot be read.
Display A Cause/Solution Cannot reset file numbering. File numbering cannot be reset because the sequential number of a folder has reached the upper limit. Insert a new memory card or format the memory card. 10, E106 Memory contains no images. Insert a memory card that contains images. 10 File contains no image data. The file was not created or edited with this camera. The file cannot be viewed on this camera. View the file using a computer or the device used to create or edit this file.
Display The maximum number of log data events that can be saved per day is 36. Cannot save to card. A Cause/Solution A memory card is not inserted. Insert a memory card. 10 – Log has not been obtained. E43 The maximum number of log data events that can be saved in one memory card is 100. Replace the memory card with a new one or delete log data that is no longer required from the memory card. 10, E44 Reference Section No access.
Display Cause/Solution A Printer error: check printer status. After solving the problem, select Resume and press the k button to resume printing.* – Printer error: check paper. Load the specified size of paper, select Resume, and press the k button to resume printing.* – Printer error: paper jam. Remove the jammed paper, select Resume, and press the k button to resume printing.* – Printer error: out of paper.
File Names Images or movies are assigned file names as follows. File name: DSCN0001.JPG (1) (2) (3) (1) Identifier Not shown on the screen of the camera.
Optional Accessories Battery Charger Battery Charger MH-67P It takes about 3 hours and 20 minutes to charge a fully exhausted battery. AC Adapter EH-67A (connect as shown) AC Adapter Before closing the battery-chamber/memory card slot cover, fully insert the power connector cable into the slot in the battery chamber. If part of the cable protrudes from the slots, the cover or cable may be damaged when the cover is closed. Hand Strap Hand Strap AH-CP1 Availability may vary with country or region.
Principle Functions of the Controls For Shooting Control Main Function A Change the shooting mode. 24 Move toward g (i) (telephoto) to zoom in closer to the subject, and move toward f (h) (wide-angle) to zoom out and view a larger area. 20 Widen the angle of view temporarily. 21 Mode dial Zoom control Snap-back zoom button Reference Section Side zoom control Multi selector E116 Use the function assigned in Assign side zoom control.
Control Command dial 30, 32 • When the shooting mode is k or m: Set the shutter speed. 30, 32 Display and hide the menu. 49, 51, 54, 55, 57 When pressed halfway (i.e., if you stop pressing when you feel resistance slightly): Set focus and exposure. When pressed all the way (i.e., if you press the button all the way down): Release the shutter. 17, 21 Start and stop movie recording.
Control Main Function A Play back images. 22 Delete the last image that was saved. 23 c (playback) button l (delete) button For Playback Control c (playback) button Main Function 22 • Return to shooting mode. 22 • Move toward g (i) to zoom in on the image, and move toward f (h) to display images as thumbnails or the calendar. • Adjust the volume for movie playback.
Control k (apply selection) button Main Function A • Display individual images of a sequence in full-frame playback mode. • Scroll an image shot with Easy panorama. • Play back movies. • Switch from thumbnail playback or zoomed image display to full-frame playback. • While the setting screen is displayed, apply the selection. 56, E25 E12 E32 E23, E24 Switch the magnification of an enlarged image. E23 Display and hide the menu. 49, 55 Delete images.
Control Main Function A Shutter-release button Return to shooting mode.
Technical Notes and Index Caring for the Product..................................... F2 The Camera.............................................................................................F2 The Battery..............................................................................................F3 The Charging AC Adapter .................................................................F4 Memory Cards........................................................................................
Caring for the Product Observe the precautions described below in addition to the warnings in “For Your Safety” (Avi-viii) when using or storing the device. The Camera Do Not Apply Strong Impact to the Camera The product may malfunction if subjected to strong shock or vibration. In addition, do not touch or apply force to the lens or lens cover. Keep Dry The device will be damaged if immersed in water or subjected to high humidity.
Notes About the Monitor • Monitors and electronic viewfinders are constructed with extremely high precision; at least 99.99% of pixels are effective, with no more than 0.01% being missing or defective. Hence while these displays may contain pixels that are always lit (white, red, blue, or green) or always off (black), this is not a malfunction and has no effect on images recorded with the device. • Images in the monitor may be difficult to see under bright lighting.
Using the Battery When Cold On cold days, the capacity of batteries tends to decrease. If an exhausted battery is used at a low temperature, the camera may not turn on. Keep spare batteries in a warm place and exchange as necessary. Once warmed, a cold battery may recover some of its charge. Battery Terminals Dirt on the battery terminals may prevent the camera from functioning. Should the battery terminals become dirty, wipe them off with a clean, dry cloth before use.
Memory Cards Precautions for Use • Use only Secure Digital memory cards. See “Approved Memory Cards” (F20) for recommended memory cards. • Be sure to follow the precautions described in the documentation included with the memory card. • Do not put labels or stickers on memory cards. Formatting Technical Notes and Index • Do not format the memory card using a computer. • The first time you insert a memory card that has been used in another device into this camera, be sure to format it with this camera.
Cleaning and Storage Cleaning Do not use alcohol, thinner, or other volatile chemicals. Lens/ viewfinder Avoid touching glass parts with your fingers. Remove dust or lint with a blower (typically a small device with a rubber bulb attached to one end that is pumped to produce a stream of air out the other end).
Troubleshooting If the camera fails to function as expected, check the list of common problems below before consulting your retailer or Nikon-authorized service representative. Power, Display, Settings Issues Problem Cause/Solution A • Wait for recording to end. • If the problem persists, turn the camera off. If the camera does not turn off, remove and reinsert The camera is on the battery or batteries or, if you are using an AC but does not adapter, disconnect and reconnect the AC adapter. respond.
Problem The camera becomes hot. – Technical Notes and Index The battery inserted in the camera cannot be charged. 11 • Confirm all connections. • When connected to a computer, the camera may not charge for any of the reasons described below. - Off is selected for Charge by computer in the 49, 58 setup menu. - Battery charging stops if the camera is turned off.
Problem Date not stamped on images even when Date stamp is enabled. Cause/Solution • The current shooting mode does not support Date stamp. • A function that restricts the Date stamp function is enabled. A 49, 57 46 • The date cannot be stamped on movies. Screen for setting time zone and date is displayed when The clock battery is exhausted; all settings were the camera is restored to their default values. turned on. – 15, F8 The camera settings reset.
Problem Cause/Solution • The subject is too close. Try shooting using the Scene auto selector or Close-up scene mode, or the macro close-up focus mode. The camera cannot focus. Colored stripes appear in the monitor when shooting. Images are blurred. • Incorrect focus mode setting. Check or change the setting. • The subject is hard to focus on. • Set AF assist in the setup menu to Auto. • Subject is not in focus area when the shutter-release button is pressed halfway.
Problem Cause/Solution Off is selected for Shutter sound in Sound settings No sound when in the setup menu. No sound is produced with some the shutter is shooting modes and settings, even when On is released. selected. A 46, 49, 57 Off is selected for the AF assist option in the setup AF-assist menu. AF-assist illuminator may not light depending on illuminator does 49, 57 the position of the focus area or the current scene not light. mode, even when Auto is selected. Images appear smeared.
Problem Saving images takes time. A ring-shaped belt or rainbowcolored stripe appears in the monitor or images. Cause/Solution It may take more time to save images in the following situations: • When the noise reduction function is in operation • When the flash mode is set to V (auto with red-eye reduction/red-eye reduction) • When capturing images in the following scene modes.
Playback Issues Problem File cannot be played back. Cause/Solution A – • This camera may not be able to play back images saved with another make or model of digital camera. • This camera may not be able to play back data edited – on a computer. • Files cannot be played back during interval timer 49, 52 shooting. • Playback zoom cannot be used with movies. • This camera may not be able to zoom in on images captured with another make or model of digital Cannot zoom in camera. on image.
Problem Cause/Solution A Images to be printed are not displayed. The memory card contains no images. – Cannot select paper size with the camera. The camera cannot be used to select the paper size in the following situations, even when printing from a PictBridge-compatible printer. Use the printer to select the paper size. • The printer does not support the paper sizes specified by the camera. • The printer automatically selects the paper size.
Cause/Solution A • Check the following items. - Whether the memory card is inserted - Whether the A-GPS file is stored on the memory card - Whether the A-GPS file saved on the memory card is more recent than the A-GPS file saved in the camera - Whether the A-GPS file is still valid • The A-GPS file may be corrupted. Download the file from the website once more. – Problem Unable to update the AGPS file. Unable to select Create log in Clock not set. the location data Set date and time. options menu.
Specifications Nikon COOLPIX P610 Digital Camera Type Number of effective pixels Image sensor Lens Focal length f/-number Construction Digital zoom magnification Vibration reduction Autofocus (AF) Focus range Focus-area selection Technical Notes and Index F16 Viewfinder Frame coverage (shooting mode) Frame coverage (playback mode) Monitor Frame coverage (shooting mode) Frame coverage (playback mode) Compact digital camera 16.0 million (Image processing may reduce the number of effective pixels.) 1/2.
Storage Media File system File formats Image size (pixels) ISO sensitivity (Standard output sensitivity) Exposure Metering mode Exposure control Shutter Aperture Range Self-timer Flash Range (approx.
Interface USB connector HDMI output connector Wireless LAN Standards Range (line of sight) Operating frequency Authentication Access protocols Location data Supported languages Power sources Technical Notes and Index F18 Charging time Battery life1 Still images Movie recording (actual battery life for recording)2 Tripod socket Dimensions (W × H × D) Micro-USB connector (Do not use any USB cable other than the UC-E21.
Weight Operating environment Temperature Humidity Approx. 565 g (1 lb 4.0 oz) (including battery and memory card) 0°C–40°C (32°F–104°F) 85% or less (no condensation) • Unless otherwise stated, all figures assume a fully-charged battery and an ambient temperature of 23 ±3°C (73.4 ±5.4°F) as specified by the Camera and Imaging Products Association (CIPA). 1 Battery life may vary depending on conditions of use, such as the interval between shots or the length of time that menus and images are displayed.
Approved Memory Cards The following Secure Digital (SD) memory cards have been tested and approved for use in this camera. • Memory cards with an SD Speed Class rating of 6 or faster are recommended for recording movies. When using a memory card with a lower Speed Class rating, movie recording may stop unexpectedly.
AVC Patent Portfolio License This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC standard (“AVC video”) and/or (ii) decode AVC video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC video. No license is granted or shall be implied for any other use.
USER LICENSE AGREEMENT FOR LOCATION NAME DATA The location name data that is stored in this digital camera (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and conditions which are agreed to by you, on the one hand, and Nikon Corporation (“Nikon”) and its licensors (including their licensors and suppliers) on the other hand. Terms and Conditions Personal Use Only.
Disclaimer of Liability: NIKON AND ITS LICENSORS (INCLUDING THEIR LICENSORS AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU: IN RESPECT OF ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OF THE NATURE OF THE CAUSE OF THE CLAIM, DEMAND OR ACTION ALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT, WHICH MAY RESULT FROM THE USE OR POSSESSION OF THE INFORMATION; OR FOR ANY LOSS OF PROFIT, REVENUE, CONTRACTS OR SAVINGS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF YOUR USE
Government End Users. If the Data supplied by HERE is being acquired by or on behalf of the United States government or any other entity seeking or applying rights similar to those customarily claimed by the United States government, the Data is a “commercial item” as that term is defined at 48 C.F.R. (“FAR”) 2.
Notices related to licensed software copyright holders. • Location name data for Japan © 2013 ZENRIN CO., LTD. All rights reserved. This service uses POI data of ZENRIN CO., LTD. “ZENRIN” is a registered trademark of ZENRIN CO., LTD. • Location name data except for Japan © 1987-2014 HERE All rights reserved.
Technical Notes and Index Italy: La Banca Dati Italiana è stata prodotta usando quale riferimento anche cartografia numerica ed al tratto prodotta e fornita dalla Regione Toscana. Contains data from Trasporto Passeggeri Emilia-Romagna- S.p.A. Includes content of Comune di Bologna licensed under (http://creativecommons.org/licenses/by/3.0/ legalcode) and updated by licensee July 1, 2013. Includes content of Comune di Cesena licensed under (http://creativecommons.org/licenses/by/3.
United States: ©United States Postal Service 2013. Prices are not established, controlled or approved by the United States Postal Service. The following trademarks and registrations are owned by the USPS: United States Postal Service, USPS, and ZIP+4. Includes data available from the U.S. Geological Survey. Australia: Copyright. Based on data provided under license from PSMA Australia Limited (www.psma.com.au).
Index Symbols Technical Notes and Index A Auto mode ............................ 16, 26 y Scene mode......................... 27 l Aperture-priority auto mode .............................................................. 30, 32 k Shutter-priority auto mode .............................................................. 30, 32 u Special effects mode..... 28 c Landscape mode ......... 24, E4 j Programmed auto mode .............................................................. 30, 32 m Manual mode ..........
Black and white copy n ........................................................ 27, E6 Brightness ........................... 57, E100 BSS........................................ E6, E67 Button sound.............................. E105 C D Date and time .......... 14, 57, E97 Date stamp......................... 57, E102 Daylight saving time...... 14, E98 Delete...................................... 23, E26 Digital zoom.......... 20, 57, E104 Diopter adjustment control .......... 19 Direct Print ...........
Focus lock......................................... E21 Focus mode.................................. 25, 40 Food u ...................................... 27, E6 Format........................ 10, 58, E106 Format memory cards ........................................ 10, 58, E106 Frame rate............................. 54, E86 Full-frame playback .......................... 7, 22, E23, E24 Full-time AF ....................... 52, 54, E75, E84 Functions that cannot be used simultaneously........................
N Q Night landscape mode..... 27, E3 Night portrait mode........... 27, E3 N-Mark................................................ E46 Noise reduction filter ..... 52, E76 Nostalgic sepia....................................... 28 Number of exposures remaining ...................................................... 16, E55 Quick adjust .................................... E59 Quick retouch ..................... 55, E27 O Optical zoom .......................................... 20 Optional accessories ......
Technical Notes and Index Shutter-priority auto mode .............................................................. 30, 32 Shutter-release button .................... 17, 21, E117, E120 Side zoom control .......... 17, E116 Single....................................... 52, E66 Single AF ....................... 52, 54, E75, E84 Skin softening .................................. 55, E20, E28 Slide show ............................ 55, E88 Slot empty release lock ...............................................
Zoom memory .................. 53, E79 Zoom microphone..........
No reproduction in any form of this manual, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. DANGER - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. • If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration for the power outlet. • This power unit is intended to be correctly orientated in a vertical or floor mount position.
Nikon Serial No. Model c:OOLPIX P6l0 See the reverse side for details WARRANTY PROGRAMS CAMERA/ACCESSORY (USA) Register your product online: 1111t111VV.nikonusa.comlregister Registration not required for warranty coverage.
Nikon Inc. CAMERA/ACCESSORY ONE YEAR USA LIMITED WARRANTY This is your Nikon Inc. Camera/ Accessory One Year USA Limited Warranty {valid in the Continental United States, Alaska, Hawaii, Puerto Rico and U.S. Virgin Islands) YOU MUST PRESENT THIS FORM TOGETHER WITH PROOF OF PURCHASE AND PROOF OF PURCHASE DATE (BILL OF SALE) TO OBTAIN WARRANTY SERVICE. This Nikon product is warranted by Nikon Inc. to be free from defects in material and workmanship for a period of one (1) year from the date of purchase.