INC VBA23001-R.3762.A 作成承認印 配布許可印 サービス 計画課 Ｍ VBA23001 REPAIR MANUAL Copyright ｃ 2008 by Nikon Corporation. All Rights Reserved.
INC Contents VBA23001-R.3762 .A Points to notice for Disassembly and Assembly ..............................................................................................................Ｄ 1 Disassembly 1. External area Bottom cover............................................................................Ｄ 2 Removal of Back cover.................................................................... Ｄ 3 2. Back cover Rear display FPC unit...................................................................
INC VBA23001-R.3762 .A 4. Separation of Front body from Rear body Eyepiece mold.......................................................................... Ｄ 40 5. Rear body SB/IF PCB..............................................................................Ｄ 42 DC/DC PCB ............................................................................Ｄ 42 Imaging power PCB unit...................................................................Ｄ 44 Bottom plate unit.............................................
INC VBA23001-R.3762 .A Assembly / Adjustment 1. Front body unit Main mirror unit..........................................................................Ａ 3 Preview SW............................................................................. Ａ 4 F-min SW............................................................................... Ａ 5 Release button...........................................................................Ａ 5 A/M change SW...............................................................
INC VBA23001-R.3762 .A 4 .Mounting Front body on Rear body. Eyepiece mold........................................................................... Ａ 44 Inspection and Adjustment of Body back...................................................Ａ 45 Main PCB.............................................................................. Ａ 48 Mount the main condenser................................................................. Ａ 50 5. Top cover Microphone...................................................
INC VBA23001-R.3762 .A 6.Back cover SD cover unit............................................................................ Ａ 92 Button / SW.............................................................................Ａ 93 TFT monitor............................................................................ Ａ 94 Rear display FPC unit.....................................................................Ａ 95 Mounting of Back cover...................................................................Ａ 100 7.
INC Points to notice for Disassembly and Assembly VBA23001-R.3762 .A ! WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. Caution: ① In disassembly/(re)assembly, be sure to use conductive mat (J5033) and wrist strap (J5033-5), in order to protect electric parts from static electricity.
INC Disassembly VBA23001-R.3762 .A 1. External area Bottom cover ・Tilt the battery cover unit (#B151) at approx. a 35-degree 35 angle, and pull it out. ・Take Take out the two screws (#657), the two screws (#658), the screw (#661), and the two screws (#692). ・Remove Remove the bottom cover unit (#25).
INC VBA23001-R.3762 .A Removal of Back cover ・Take Take out the two screws (#608). ・Take Take out the four screws (#657). Screw (#608)×2 Screw (#657)×4 ・Slacken the grip side of the cover first, and then remove the cover wholly. ・Disconnect Disconnect the FPC of the back cover from the connector on the DG PCB unit.
INC VBA23001-R.3762 .A 2. Back cover ・Peel Peel off the cover rubber (#407) and the double-stick tape (#409). ・Remove Remove the SD access lamp window (#408). SD access lamp window (#408) Double-stick tape (#409) Cover rubber (#407) Rear display FPC unit ・Remove Remove the gasket (#483). ・Peel Peel off the tape [TA-0005 (12.5×12.5)]. (12.5 Gasket (#483) Tape [TA-0005 (12.5 × 12.
INC VBA23001-R.3762 .A ・Take Take out the ten screws (#670). ・Disconnect Disconnect the connector. Screw (#670)×6 Screw (#670)×4 ・Take Take out the three screws (#710).
INC VBA23001-R.3762 .A ・Remove Remove the plate (#422). ・Remove Remove the rear display FPC unit (#B1034) together with the plate (#415).
INC VBA23001-R.3762 .A ・Peel Peel off the rear display FPC unit (#B1034) from the plate (#415). Rear display FPC unit (#B1034) Plate (#415) ・Peel Peel off the double-stick tape (#423) from the plate (#415).
INC VBA23001-R.3762 .A TFT monitor ・Take Take out the screw (#710). ・Remove Remove the plate (#406). ・Remove Remove the TFT monitor (#1057).
INC VBA23001-R.3762 .A Button / SW-related ・Remove Remove the buttons (#421, #429, and #430). Button (#430) Button (#421) Button (#429) ・Remove Remove the conducting rubber (#413). ・Remove Remove the button (#414). ・Remove Remove the multi-selector (#412). Screw (ROHS) (#707) △（Revision） ・Take Take out the screw (#707). ・Remove Remove the selector SW unit (#B420). ・Remove Remove the selector lock lever (#416).
INC VBA23001-R.3762 .A SD cover unit ・Take Take out the two screws (#621), and remove the SD cover unit (#B431). Screw (#621) × 2 SD cover unit (#B431) ・Peel Peel off the label (#436).
INC VBA23001-R.3762 .A ・Peel Peel off the rubber (#433). ・Peel Peel of the drip-proof sheet (#44). Drip-proof sheet (#44) Rubber (#433) ・Peel Peel off the two sponges each (#404 and #405). (#405) (#404) (#404) (#405) ・Remove Remove the TFT monitor cover (#402). ・Peel Peel off the double-stick tape (#403).
INC VBA23001-R.3762 .A Speaker unit ・Disconnect Disconnect the connector. ・Take Take out the two screws (#612), and remove the speaker unit (#B45). Speaker unit (#B45) Screw (#612)×2 DG-shield plate ・Disconnect Disconnect the image sensor unit-FPC. ・Take Take out the six screw (#683). ・Remove the shield plate (#78) and shield plate unit (#B79) carefully not to damage the clip.
INC VBA23001-R.3762 .A DG PCB unit ・Disconnect Disconnect the three FPCs and two harnesses. ・Take Take out the two screws (#683). Screw (#683) Screw (#683)×1 DG PCB unit (#B1031) ・Remove Remove the DG-PCB unit (#B1031). ・Disconnect Disconnect the wire of the microphone.
INC VBA23001-R.3762 .A Image sensor unit ・Unsolder Unsolder the wires (Red/Black/Orange/Gray). Wire ×4 (Red/Black/Orange/Gray) ・Take out the three screws (#680), and remove the image sensor unit (#B1051). Caution: Some bodies have already the lumirror sheet T=0.1(#62) and washer (#63) attached. (ref.
INC VBA23001-R.3762 .A A/M cover plat A/M cover plate △（Revision） ・Remove Remove the A/M cover plate (black) (#124) (carefully NOT to damage it). ・Take Take out the screw (#659), and remove the A/M select lever (#121). A/M cover plate (black) (#124) A/M select lever (#121) Screw (#659) SB pop-up ・ Cut the lumirror sheet, etc, into a below-size piece. Then, insert it into the gap of the top cover pop-up section as below, and slide it in the direction of the arrow to raise the speedlight.
INC VBA23001-R.3762 .A Front cover unit ・ Take out the two screws (#611). ・ Take out the two screws (#613). ・ Remove the front cover unit (#B24). Screw (#611) ×2 Front cover unit (#B24) Screw (#613) ×2 ・Remove Remove the E-ring (#722). ・Remove Remove the spring (#201) and the button (#229). ・Remove the snap ring (#387) from behind. ・Remove Remove the buttons (#391 and #392) from the front cover unit .
INC VBA23001-R.3762 .A Grip rubber unit ・Take Take out the screws (#627 and #618). ・Remove Remove the grip rubber unit (#B26). Screw (#627) Battery chamber Screw (#618) ・Peel Peel off the tape [TA0005 (3.3×11)]. (3.3 ・Peel Peel off the tape (#811). ・Remove Remove the plate (#388). ・Remove Remove the button (#390) and the conducting rubber (#389). ・Attach the spring (#161) from behind, and take out the screw (#638). ・Remove the grip red mold (#29) from the front side of the grip cover.
INC VBA23001-R.3762 .A I/F cover ・Remove Remove the IF cover (#71) and the cable release cover (#70). ・Remove Remove the IF cover (#B28). IF cover (#71) IF cover (#B28) Cable release cover (#70) ・ Remove the tape (#755) from the IF cover (#B28).
INC VBA23001-R.3762 .A ! WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. ・Pass the tip of the discharging device straight through the round-hole as below.
INC VBA23001-R.3762 .A Removal of top cover ・Peel off the tape (#831). ・Unsolder Unsolder the wires (Black/Pink/Orange/Blue) of the top cover. Wire ×4 (Black/Pink/Orange/Blue) ・Remove Remove the wires from the grooves. ・Unsolder Unsolder the wires (Blue/Green/Yellow) of the preview unit. ・Unsolder Unsolder the wires (Red/Black) of the main condenser.
INC VBA23001-R.3762 .A ・Peel Peel off the diopter adj knob cover (#280). ・Remove Remove the screw (#288). ・Remove Remove the sponge (#287) from the diopter adj knob (#282). ・Remove Remove the roller (#281) from the body. Roller (#281) Sponge (#287) Screw (#288) Diopter adj knob (#282) Diopter adj. knob cover (#280) ・Take Take out the screw (#636). Screw (#636) ・Take Take out the two screw (#657). ・Take Take out the two screw (#677).
INC VBA23001-R.3762 .A ・Peel Peel off the tape [TA-0005 (6×10)]. (6 ・Remove Remove the wires of the microphone (#1051) from the cutout of the body. Wires of the microphone (#1051) cutout Tape [TA-0005 (6×10)] ・Disconnect Disconnect the FPC from the connector of the top cover unit (#B23RP). ・Remove Remove the top cover unit (#B23RP).
INC VBA23001-R.3762 .A 3. Top cover AF-assist lamp unit ・Unsolder Unsolder the two wires (Black) of the AF-assist lamp unit (#B325). ・Take Take out the screw (#611). AF-assist lamp unit (#B325) Screw (#611) Wire ×2 (Black) Top cover FPC unit ・Unsolder Unsolder the wires (Red/Black). ・Unsolder Unsolder the wires (Brown/Yellow). ・Remove Remove the five solders of the shoe mold unit (#B317).
INC VBA23001-R.3762 .A ・Disconnect Disconnect the connector. ・Remove Remove the wires (black/pink/orange/blue) from the two guides.
INC VBA23001-R.3762 .A ・Remove Remove the six solders, and take out the four screws (#635). Screw (#635) × 2 Screw (#635) × 2 ・Remove Remove the MC/D unit (#B367) and the SC/D unit (#B377).
INC VBA23001-R.3762 .A ・Take Take out the screw (#607). ・Take Take out the screw (#605). ・Take Take out the screw (#612), and remove the arrangement plate (#340). ・Remove Remove the three screws (#612) which are for the top cover FPC unit (#B1007RP). Screws (#612) which are for the top cover FPC unit (#B1007RP) Screw (#607) Arrangement plate (#340) Screw (#605) ・Remove Remove the top cover FPC unit (#B1007RP).
INC VBA23001-R.3762 .A ・Peel Peel off the tape (#825). Tape (#825) ・Unhook Unhook the plate (#331) at four places from the top cover FPC unit (#B1007RP). ・Remove Remove the upper LCD (#1044). ・Remove Remove the two conducting rubber (#332). ・Remove Remove the reflection sheet (#334) and the light guide (#333).
INC VBA23001-R.3762 .A AE-L button ・Remove Remove the conducting rubber (#397) and the button (#381). Conducting rubber (#397) Button (#381) Top cover grip button ・Remove Remove the conducting rubber (#339).
INC VBA23001-R.3762 .A Power dial ・Take Take out the two screws (#602). ・Remove Remove the contact brush (#348) and the click spring (#347). Click spring (#347) Screw (#602)× 2 Contact brush (#348) ・Peel Peel off the sheet (#352). ・Remove Remove the spring (#346) (carefully to avoid popping out of the spring) and the release button unit (#B350).
INC VBA23001-R.3762 .A Hot shoe ・Take Take out the four screws (#654). ・Remove the GND plate (#322) and the holder (#321) from bottom. ・Remove the hot shoe (#316), hot shoe spring (#318), and shoe mold unit (#B317). Hot shoe spring (#318) Hot shoe (#316) Shoe mold unit (#B317) Screw (#654)× 2 Screw (#654)× 2 Holder (#321) GND plate (#322) SB upper cover ・Raise the speedlight and take out the two screws (#629).
INC VBA23001-R.3762 .A ・ Unhook by pushing the red dot framed areas( ) as below. ・ Put the speedlight down approximately half way. ・ Remove the SB upper case (#301). SB upper case [#301] SB lower control unit ・Remove Remove the wires from the two guides.
INC VBA23001-R.3762 .A ・Pull Pull out the wires. ・While holding the rear SB case rotate shaft (#306), take ake out the screw (#650). Screw (#650) Hold the rear (#306). ・Remove Remove the spring (#305) (carefully to avoid popping out of the spring).
INC VBA23001-R.3762 .A ・Remove Remove the roller (#308) and the SB case rotate shaft (#306). SB case rotate shaft (#306) Roller (#308) ・Remove Remove the SB lower control unit (#B2302). ・Remove Remove the flash pop-up arm A (#B341) and the flash pop-up arm B (#B342).
INC VBA23001-R.3762 .A Remote control unit ・Unsolder Unsolder at three places. ・Take Take out the screw (#607), and remove the remote control unit (#B1056). Screw (#607) Remote control unit (#B1056) M/D FPC unit ・Take Take out the three screws (#640). ・Remove Remove the M/D FPC unit (#B2455).
INC VBA23001-R.3762 .A Delete button ・Remove Remove the conducting rubber (#399) and the button (#398). Button (#398) Conducting rubber (#399) Mode dial ・Take Take out the screw (#640). ・Remove Remove the mode dial (#451), the click spring (#453) and the contact brush (#452). ・Peel Peel off the tape [TA-0026 (8×8)], (8 )],, and the mode dial cap (#460).
INC VBA23001-R.3762 .A ・Peel Peel off the two sponges each (#336 and #337). ・Peel Peel off the two sponges each (#756 and #758). (#758)×2 (#756)×2 (#336)×2 (#337)×2 ・Remove Remove the AF-assist lamp protector (#326). ・Remove Remove the remote control window (#463). ・Peel Peel off the double-stick tape (#338), and remove the LCD window (#335).
INC VBA23001-R.3762 .A Removal of the main condenser ・Unsolder Unsolder the wires (Red/Black). ・Take Take out the screw (#683). Screw (#683) Wire × 2 (Red/Black) ・Remove Remove the main condenser unit (#B42).
INC VBA23001-R.3762 .A Main PCB unit ・Unsolder Unsolder the wires (Red/Black) of the front body FPC. ・Disconnect Disconnect the connector at five places.
INC VBA23001-R.3762 .A ・Take Take out the two screws (#640). Main PCB (#1001) Screw (#640)× 2 ・Remove Remove the main PCB (#1001), being careful of the connector.
INC VBA23001-R.3762 .A 4. Separation of Front body from Rear body ・Remove Remove the solder bridge at two places on the power drive PCB (#B1002). ・Unsolder Unsolder the wires (Black/Gray) of the mount GND. ・Unsolder Unsolder the wires (Black/Red) of the SQ motor. ・Unsolder Unsolder the wires (Black) of the buzzer unit. Solder bridges Wire× 2 (Black/Gray) of the mount GND Wire× 2 (Black/Red) of SQ motor Wire× 2 (Black) of the buzzer unit Eyepiece mold ・Take Take out the two screws (#615).
INC VBA23001-R.3762 .A ・Take Take out the two screws (#702), four screws (#706), and two screws (#615). ・Remove Remove the front body unit from the rear body.
INC VBA23001-R.3762 .A 5. Rear body SB/IF PCB ・Unsolder Unsolder the wires (Red/Black/Orange). ・Take Take out the two screws (#612). ・Remove Remove the SB/IF PCB unit (#B1041). Wire × 3 (Red/Black/Orange) Screw (#612) × 2 SB/IF PCB unit (#B1041) DC/DC PCB ・Take Take out the two screws (#683). ・Remove Remove the GND plate unit (#B109).
INC VBA23001-R.3762 .A ・Unsolder Unsolder the wires (Red/Black/Green). ・Take Take out the screw (#683). Wire × 3 (Red/Black/Green) Screw (#683) ・Remove Remove the DC/DC PCB (#B1030).
INC VBA23001-R.3762 .A ・Take Take out the two screws (#683). ・Unhook Unhook the GND plate (#110). Unhook GND plate (#110) Screw (#683) ×2 Imaging power PCB unit ・Take Take out the three screws (#683). ・Remove Remove the shield plate (#B108) and the imaging power PCB unit (#B1029).
INC VBA23001-R.3762 .A ・Take Take out the screw (#683). ・Remove Remove the GND plate unit (#B141). Screw (#683) GND plate unit (#B141) Bottom plate unit ・Take Take out the screws (#706). ・Unhook Unhook the GND plate (#140) from the rear body , and remove the bottom plate unit (#B67) from the rear body .
INC VBA23001-R.3762 .A ・Take Take out the two screws (#617). ・Remove Remove the bottom plate unit (#B67). ・Remove Remove the GND plate (#140). Screw (#617) ×2 Bottom plate unit (#B67) GND plate (#140) Power drive PCB unit ・Take Take out the three screws (ROHS) (#609). ・Remove Remove the OP-FPC unit (#B1016). OP-FPC unit (#B1016) Screw (ROHS) (#609) ・Unsolder Unsolder the wires (red/black/orange). ・Remove the three solder bridges.. ・Take Take out the two screws (#683).
INC VBA23001-R.3762 .A ・Remove Remove the power drive PCB (#B1002). Power drive PCB (#B1002) ・Remove Remove the GND plate (#142).
INC VBA23001-R.3762 .A Battery contact-spring ・Take Take out the three screws (#619). ・Remove Remove the FG/ID contact-spring (#80) and the two battery contact-springs (#157). Battery contact-spring (#157) FG/ID contact-spring (#80) Screw (#619) Battery contact-spring (#157) ・Remove Remove the (back-side) wires (Orange/Black/Red). ・Remove Remove the (Bayonet-side) wires (Red/Black).
INC VBA23001-R.3762 .A ・Remove Remove the GND plate (#143). ・Remove Remove the GND plate (#107). ・Remove Remove the wires (Orange/Black/Red).
INC VBA23001-R.3762 .A Eyelet ・Take Take out the two screws (#614). ・Remove Remove the eyelet (#145) and the GND plate (#149). GND plate (#149) Eyelet (#145) Screw (#614)× 2 ・Take Take out the two screws (#614). ・Remove Remove the eyelet (#146). ・Peel Peel off the sponges (#760 and #763). ・Remove Remove the GND plate (#150). GND plate (#150) Screw (#614)× 2 Sponge (#763) Sponge (#760) Eyele (#146) ・Take Take out the screw (#683). ・Remove Remove the GND plate (#106).
INC VBA23001-R.3762 .A ・Peel Peel off the sponge (#762) from the eyelet (#145). Sponge (#762) Eyelet (#145) Buzzer unit ・Remove Remove the buzzer unit (#1055). Buzzer unit (#1055) Drip-proof sponge ・Peel Peel off the two sponges (#753). ・Peel Peel off the sponge (#766). ・Peel Peel off the sponge (#761).
INC VBA23001-R.3762 .A ・Peel Peel off the sponge (#751). Sponge (#751) Dust-proof tape ・Peel off each tapes [TA0026 (8×50), #733 and #734].
INC 6. Separation of Prism box unit from Front body unit ・Take Take out the four screws from the P-box unit. Screw (#642) × 4 - D53 ･ D90 - VBA23001-R.3762 .
INC VBA23001-R.3762 .A 7. Prism box unit Metering FPC unit ・Take Take out the three screws (#607), and remove the metering FPC unit (#B11008). Screw (#607)× 3 Metering FPC unit (#B11008) Inside finder LCD unit ・Disconnect Disconnect the FPC of the inside finder LCD unit (#B1010) from the connector on the penta prism FPC unit (#B1021). Inside finder LCD unit (#B1010) ・Take Take out the two screws (#708), and remove the inside finder LCD unit (#B1010).
INC VBA23001-R.3762 .A Screen box ・Peel Peel off the tape [TA0009 (7×5)]. (7 ・Disconnect Disconnect the FPC of the SI unit (#B1046) from the connector on the penta prism FPC unit (#B1021). Tape [TA0009 (7×5)] SI unit (#B1046) ・Remove Remove the screen box plate (#511) by unhooking from the penta prism box unit (#261) and releasing from the side bosses. Unhook (#511) ・Remove Remove the screen box assembly.
INC VBA23001-R.3762 .A ・Unhook Unhook the spring (#265) from the screen box (#510), and remove the fresnel lens (#3) and sponge (#527). Unhook Screen box (#510) Washer (#266) Fresnel lens (#3) Spring (#265) ・Unhook Unhook the retainer spring (#534) from the screen box (#510), and remove the view field frame 1 (#263) and the SI unit (#B1046).
INC VBA23001-R.3762 .A Penta prism ・Peel off the upper part of the penta prism FPC unit (#B1021) from the penta prism as below. Penta prism FPC unit (#B1021) ・Peel Peel off the dust-prevent sheet (#298). Dust-prevent sheet (#298) ・Remove Remove the two springs (#268).
INC VBA23001-R.3762 .A ・Peel Peel off the double-stick tape (#781). ・Remove Remove the insulation sheet (#270). ・Peel Peel off the double-stick tape (#780). ・Remove Remove the penta prism retainer (#267) and the protection sheet (#269). Double-stick tape (#781) Insulation sheet (#270) Double-stick tape (#780) Penta prism retainer (#267) Protection sheet (#269) ・Remove Remove the penta prism (#4) and the view field frame 2 (#264).
INC VBA23001-R.3762 .A ・Remove Remove the spacer (#535). Spacer (#535) Penta prism FPC unit ・Take Take out the four screws (#635). Screw (#635)× 4 ・Remove Remove the two plates (#532) and the penta prism FPC unit (#B1021).
INC VBA23001-R.3762 .A ・Peel Peel off the tape (#521). ・Remove Remove the light guide (#503). ・Remove Remove the double-stick tape (#504) from the light guide (#503). ・Remove Remove the polarizer plate (#502). [#502]x2 [#504]x2 [#503]x2 [#521] [#B261RP] Eyepiece barrel unit ・Peel off the tape (#783). ・Take out the two screws (#642). ・Remove the eyepiece barrel unit (#B271) from the penta prism box unit (#B261RP). ・Remove the eyepiece lens 1 (#5) and eyepiece lens 3 (#7).
INC VBA23001-R.3762 .A 8. Front body unit SB PCB ・Disconnect Disconnect the FPC of the aperture control unit (#B241RP) from the connector. ・Take Take out the screw (#683). ・Remove Remove the SB PCB (#B1040). SB PCB (#B1040) Screw (#683) ・Peel Peel of the tape [#TA0009 (5×7)].
INC VBA23001-R.3762 .A Shutter unit ・Peel Peel off the tape (#778), and remove the solder bridge. Tape (#778) ・Turn the gear of the aperture perture control unit (B241RP) in the direction of the arrow, and raise the mirror. ・Take Take out the two screws (#638), and remove the shutter unit (#B31). Screw (#638)×2 Gear Shutter unit (#B31) AF CCD unit ・Disconnect Disconnect the FPC of the AF CCD unit (#B2163) from the connector.
INC VBA23001-R.3762 .A φ1.5mm). ・Take out the three screws (#173) with a hexagonal wrench (�������� Screw (#173)×3 ・Remove Remove the AF CCD unit (#B2163). ・Remove Remove the three springs (#170).
INC VBA23001-R.3762 .A Front body FPC ・Unsolder the wires (Red/Black) of Fmin-SW. Wire ×3 (Red/Black) ・Remove Remove the solder bridges at three places. ・Unsolder Unsolder the wires (Black/Yellow) of AM change sw. ・Unsolder Unsolder the wires (Black/Yellow) of AF motor. Wire ×2 (Yellow/Black) of AM change SW. Wire ×2 (Yellow/Black) of AF motor.
INC VBA23001-R.3762 .A ・Remove Remove the bkt-SB FPC unit (#B1014). (#B1014) ・Take Take out the two screws (#640) ・Take out the one screw (#670). ・By releasing from the bosses, turn up the FPC of the lens contact unit (#B2113). ・Remove the front body FPC (#B1009)..
INC VBA23001-R.3762 .A ・Remove Remove the holder (#560). Holder (#560) Aperture control unit ・Remove Remove the wires (Blue/Green/Yellow) of the preview SW unit from the guides. ・Remove Remove the wires (Blue/Green/Yellow) of the F-min SW from the guides.
INC VBA23001-R.3762 .A ・Raise the mirror. ・Take Take out the two screws (#624). ・Take Take out the screw (#698). Screw (#624)×2 Screw (#698) ・Remove Remove the aperture control unit (#B241RP).
INC VBA23001-R.3762 .A ・Take Take out the screws (#630 and #628). ・The sequence base plate (#B91) will come off from the aperture control unit (#B241RP).
INC VBA23001-R.3762 .A AF driving base ・Take Take out the screw (#630). ・Remove Remove the lever (#193) from the groove of the coupling shaft (#185). Coupling shaft (#185) Screw (#630) Lever (#193) ・Remove Remove the spring (#195) (carefully to avoid popping out of the spring). Spring (#195) ・Remove Remove the coupling shaft (#185). Coupling shaft (#185) ・Take Take out the two screws (#637). ・Remove Remove the AF driving base (#B172).
INC VBA23001-R.3762 .A Bayonet ・Peel Peel off the gasket (#482). ・Take Take out the screw (#660), and the five screws (#648), and remove the bayonet mount (#111). Gasket (#482) Bayonet mount (#111) Screw (#648) ×5 Screw (#660) × 1 ・Remove Remove the three bayonet springs (#112) and the GND plate (#136). GND plate (#136) Bayonet spring (#112) × 3 ・Peel Peel off the flocked sheet (#816).
INC VBA23001-R.3762 .A ・Remove Remove the F-min spring plate unit (#B135) from the bosses. ・Remove Remove the spring (#132) and the f-min block (#131) (carefully to avoid popping out of the spring). F-min spring plate unit (#B135) Spring (#132) Be careful NOT to break the bosses. F-min block (#131) ・Take Take out the two screw (#642). ・Remove Remove the lens contact unit (#B2113).
INC VBA23001-R.3762 .A A/M change sw ・Take Take out the screw (#607), and remove the A/M setting spring (#123). Screw (#607) A/M setting spring (#123) ・Take Take out the screw (#642). ・Remove Remove the A/M change SW B (#126). ・Remove Remove the A/M change SW unit (#B125).
INC VBA23001-R.3762 .A Release button ・Take Take out the two screws (#625). ・Remove Remove the lens release holder (#115). ・Pull Pull out the spring (#119) from the release button holder (#B116). Spring (#119) Lens release holder (#115) Screw (#625) × 2 Release button holder (#B116) ・Take Take out the screw (#630), and remove the vertical lever (#191). Screw (#630) Vertical lever (#191) ・Remove Remove the release button holder (#B116).
INC VBA23001-R.3762 .A F-min SW ・Take Take out the screw (#642). ・Remove Remove the f-min SW B (#134), and the f-min SW unit (#B133). ・Unsolder Unsolder the wires (Black/Red). Screw (#642) Wire × 2 (Black/Red) F-min SW B (#134) F-min sw unit (#B133) Preview sw ・Take Take out the screw (#627), and remove the preview sw unit (#B228) and the preview SW (#227). ・Unsolder Unsolder the wires (Yellow/Green/Blue).
INC VBA23001-R.3762 .A Main mirror unit ・Remove Remove the spring (#206). ・Take Take out the four screws (#670), and remove the 45-deg. holding PCB unit . ・Remove Remove the washers (#563 - #567). (Be careful NOT to lose them.) ・Remove Remove the main mirror unit (#B2231) from the front body unit . Screw (#670) × 4 Spring (#206) Washer (#563) - (#567) 45-deg.
INC VBA23001-R.3762 .A ・ Remove the preview lever-related parts. ・ Remove the aperture lever-related parts. ・ Remove the flocked sheets (#197, #198, and #199).
INC VBA23001-R.3762.A Assembly / Adjustment △（Addition） 1. Front body unit ・Attach Attach the flocked sheets (#197, #198, and #199). ・Mount the aperture lever-related. ・Mount the preview lever-related. to the inner surface of [#203, #207, and #208]. ・Apply Grease: LEN317A ・Apply Grease: MZ-800SEL to [#209] and [#210] by dipping. [#199] [#197] [#198] Grease: LEN317A [#204] Apply to overall "scooped" area.
INC VBA23001-R.3762.A Spring attaching position (Aperture lever) #205 Short #205 #212 Grease:LEN317A Long (thin) #212 Long (thick) #213 Grease:LEN317A Spring attaching position (Preview latch lever) Grease: LEN317A Dipping: Grease: MZ-800SEL Attach the spring by kind of winding the end of the spring in the protruding section of [#221].
INC VBA23001-R.3762.A Main mirror unit ・Attach the washers (#563-#567) and the main mirror unit (#B2231) to the front body unit . ・Mount the 45-deg. angle holding PCB unit . ・Check the play of the main mirror unit (#B2231). If it does not meet the standard, adjust thickness by combining up to two washers so ������������������������������ as to be within standard. (Standard: 0+0.15mm) ・Tighten the four screws (#670) in numeric order ( ① → ② ). ・Hook the spring (#206). ・Attach the sponge (#785).
INC VBA23001-R.3762.A Preview SW ������������������������������������������������������������������������������������� SW (#227) under the preview actuating lever (#221) as below, and assemble it. ・Insert the preview Preview actuating lever (#221) Preview SW (#227) ・Sandwich the preview actuating lever (#221) with the two head plates of preview SW unit (#B228). ・Mount the preview actuating lever (#221) by fitting with the bosses. ・Tighten the screw (#627). ・Solder the wires (Yellow/Green/Blue).
INC VBA23001-R.3762.A F-min SW ・Solder Solder the wires (Black/Red). ・Mount Mount the F-min SW B (#134) by fitting with bosses of the F-min SW unit (#B133). (The The contact brush of [#134] must be placed on inside of [#B133] #B133] as below.) ・Tighten Tighten the screw (#642). Wire ×2 (Black/Red) F-min SW B (#134) F-min SW unit (#B133) Screw (#642) Release button ・Mount Mount the A/M change cam (#122). Grease: LEN317A A/M change cam (#122) ・Attach Attach the release button holder (#B116).
INC VBA23001-R.3762.A ・Attach Attach the vertical lever (#191), and tighten the screw (#630). Screw (#630) Vertical lever (#191) Grease: LEN317A ・Put Put the spring (#119) into the release button holder (#B116). ・Mount Mount the lens release holder (#115). ・Tighten Tighten the screw (#625).
INC VBA23001-R.3762.A A/M change SW ・Mount Mount the A/M change SW unit (#B125) on the front body. ・Attach Attach the A/M change SW B (#126). ・Tighten Tighten the screw (#642). Screw (#642) A/M change SW B (#126) A/M change SW unit (#B125) ・Attach Attach the A/M setting spring (#123) with screw (#607). Screw (#607) A/M setting spring (#123) ・Pass the FPC of the lens contact unit (#B2113) through inside of the front body (#B22) as below.
INC VBA23001-R.3762.A Bayonet ・Attach Attach the spring (#132) to the F-min block (#131). ・Mount Mount the front body (#B22) on the three guides. Spring (#132) Dipping: Grease: CFD-409Z F-min block (#131) ・Attach Attach the F-min spring plate unit (#B135) by fitting with two bosses. F-min spring plate unit (#B135) Be careful of the bosses, because they can be easily broken.
INC VBA23001-R.3762.A ・Adhere Adhere the flocked sheet (#816). Flocked sheet (#816) ・Attache Attache the three bayonet springs (#112) and the GND plate (#136). GND plate (#136) Bayonet spring (#112) ×3 Grease: LEN317A #112×3 ・Mount the bayonet mount (#111). Tighten the one screw (#660) and the five screws (#648) in numeric order ( ①→⑥） →⑥） ⑥） ）. ・Attach the gasket (#482) so that it is not placed on the mount.
INC VBA23001-R.3762.A AF driving base ・Mount Mount the AF driving base (#B172), and tighten the two screws (#637). Screw (#637) ×2 AF driving base (#B172) ・Attach Attach the coupling shaft (#185). Coupling shaft (#185) ・Hook the spring (#195) temporarily as below. Spring (#195) ・Assemble the lever (#193) into the coupling shaft (#185) by fitting in the groove. ・Tighten Tighten the screw (#630).
INC VBA23001-R.3762.A ・Hook Hook the spring (#195) as below. Spring (#195) Aperture control PCB ・Assemble Assemble the aperture control unit (#B241RP) and the sequence base plate (#B91). ・Tighten Tighten the screw (#630) and (#628). (#B91) ref.) If the spring (#212) comes off, attach (#B241RP) it so that it engages the hooks as below.
INC VBA23001-R.3762.A ・Turn the segment gear of the aperture control unit (#B241RP) in the direction of the arrow. ・Push in the latch lever and lock it. Aperture control unit (#B241RP) Push in. Segment gear Latch lever ・Confirm that the SQ lever is not hooked in the reset lever. (If it is, turn the gear in the direction of the arrow so as to separate the SQ lever, and unhook it.) SQ lever Reset lever ・Hook Hook the shutter charge lever (#203) to the preview latch lever (#222).
INC VBA23001-R.3762.A ・Lower the aperture lever (#208). Aperture lever (#208) ・The shutter charge lever (#203) and the aperture driving lever (#207) will form an inverted-V-shaped opening. ・Put the SQ-lever arm section in there as below. Aperture driving lever (#207) SW-lever arm section Grease: LEN317A Shutter charge lever (#203) ・Fitting Fitting with the bosses. ・Tighten Tighten the two screws (#624) in numeric order ( ①→② →② ② ). ・Tighten Tighten the screw (#698).
INC VBA23001-R.3762.A ・Arrange Arrange the wires (Black/Red) of F-min SW among the boss. ・Arrange Arrange the wires (Blue/Green/Yellow) of the preview SW unit under the guides. Wire (Blue/Green/Yellow) ×3 Wire ×2 (Red/Black) Front body FPC ・Mount Mount the holder (#560).
INC VBA23001-R.3762.A ・Mount Mount the front body FPC (#B1009) by fitting with the bosses. ・Tighten Tighten the one screw (#670) and the two screw (#640). Front body FPC (#B1009) Screws (#640) ×2 Screw (#670) ・Mount Mount the BKT-SB FPC unit (#B1014) by fitting with the bosses. ・Mount Mount the AF driving base (#B172) by fitting with the bosses. ・Insert the tip of the FPCs into each hole.
INC VBA23001-R.3762.A ・Fold down the FPC of the lens contact unit (#B2113) toward the bayonet side by fitting with the bosses. ・Make Make the three solder bridges. ・Solder Solder the wires (Black/Yellow) of the A/M change SW unit. ・Solder Solder the wires (Black/Yellow) of the AF driving base (Black/Yellow). #B2113 Wire ×2 (Yellow/Black) of the A/M change SW unit Wire ×2 (Yellow/Black) of the AF driving base ・Solder Solder the wires (Red/Black) of the Fmin-SW.
INC VBA23001-R.3762.A AF CCD unit ・Insert Insert the three springs (#170). ・Mount Mount the AF CCD unit (#B2163). ・Bend the FPC inward. (#B2163) Spring (#170) ×3 ×3 Dipping: Grease: CFD-409Z ・Turn the three screws (#173) lightly all the way with HEX KEY WRENCH (φ1.5mm) ( until they stop, then give them two turns counterclockwise.
INC VBA23001-R.3762.A ・Connect Connect the FPC of the AF CCD unit (#B2163) to the connector. Shutter unit ・Turn the gear of the aperture control unit in the direction of the arrow, and raise the mirror. ・Attach Attach the shutter unit (#B31) with two screws (#638). ・Attach Attach the sponge (#817). ・Turn the gear in the direction of the arrow so that the index can be within the range of the initial position.
INC VBA23001-R.3762.A ・Make Make the solder bridge, and attach the tape (#778).
INC SB PCB VBA23001-R.3762.A ・Attach Attach the tape [#TA0009 (5×7)]. (5 ・Attach Attach the SB PCB (#1040) with the screw (#683). SB PCB (#1040) Screw (#683) ・Connect Connect the FPC of the aperture control unit (#B241RP) to the connector.
INC VBA23001-R.3762.A Height adjustment of AF coupling shaft ① Set the A/M change cam (#122) to AF side. [In this state, the coupling shaft (#185) is #652 protruded from the bayonet surface.] Adhesive: Screwlock ② Adjust the height of the coupling shaft (#185) with the screw (#652) to become "1.7±0.15mm". ③ After the adjustment, secure the screw (#652) with the screwlock. #185 1.7±0.
INC VBA23001-R.3762.A Angle inspection and adjustment of Main mirror and Sub-mirror Device: 2. Sub-mirror 59°-deg. angle inspection and adjustment 1. Main-mirror 45°-deg.
INC VBA23001-R.3762.A Angle adjustment of Main mirror and sub-mirror ※ Procedure: Follow the operating instructions of the tool for main/sub mirror angle-inspection (J19132). ・Main-mirror 45° adjustment Caution: Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times.
INC VBA23001-R.3762.A 2. Prism box Eyepiece barrel unit ・Mount the eyepiece lens 1 (#5) and eyepiece lens 3 (#7). ・Mount the eyepiece barrel unit (#B271) on the penta prism box unit (#B261RP) by fitting with the boss. ・Tighten the two screws (#642). ・Attach the tape (#783). Eyepiece lens 3 (#7) Adhesive: Super X Eyepiece lens 1 (#5) Eyepiece barrel unit (#B271) Screw (#642) ×2 Tape (#783) ・Attach Attach the double-stick tape (#504) to light guide (#503).
INC VBA23001-R.3762.A Penta prism FPC unit ・Mount Mount the penta prism FPC unit (#B1021) and the two plates (#532) by fitting with the bosses. (Be careful of the mounting direction of [#532].) Penta prism FPC unit (#B1021) Plate (#532) ×2 ・Tighten Tighten the four screws (#635). Screw (#635) ×4 Penta prism ・Attach Attach the spacer (#535).
INC VBA23001-R.3762.A ・Mount Mount the view field frame 2 (#264) and the penta prism (#4). Penta prism (#4) View field frame 2 (#264) ・Mount Mount the protection sheet (#269) and the penta prism retainer (#267). ・Attach Attach the double-stick tape (#780) to the penta prism retainer (#267). ・Hook Hook and attach the insulation sheet (#270) to the penta prism retainer (#267). (Be careful of the attaching direction of [#270].) ・Attach Attach the double-stick tape (#781).
INC VBA23001-R.3762.A ・Hook Hook the two springs (#268) in numeric order ( ①→②→③ →②→③ ②→③ →③ ③ ). Spring (#268) ×2 ② ② ① ① ③ ③ ・Attach Attach the dust prevent sheet (#298). Dust prevent sheet (#298) ・Adhere the double-stick tape (#781). ・Attach Attach the penta prism FPC unit (#B1021) by fitting with the bosses.
INC VBA23001-R.3762.A Screen box ・Mount Mount the superimpose unit (#B1046) on the screen box (#510). ・Mount Mount the view field frame 1 (#263) by fitting its edge under the FPC of the SI unit (#B1046). ・Position Position the SI unit (#B1046) and the view field frame 1 (#263) in the direction of the arrows, and mount them. ・Hook Hook the retainer spring (#534) by fitting with the bosses. Retainer spring (#534) View field frame 1 (#263) SI unit (#B1046) Fit under the FPC of SI unit.
INC VBA23001-R.3762.A ・Mount Mount the screen box assembly. Screen box assembly ・Attach Attach the screen box plate (#511) by fitting with bosses, and engage the hook of the penta prism box. (#511) Hook ・Connect Connect the FPC of the SI unit (#B1046) to the connector on the penta prism FPC unit (#B1021). ・Attach the tape [TA0009 (7×5)].
INC VBA23001-R.3762.A Inside finder LCD unit ・Mount Mount the inside finder LCD unit (#B1010), and tighten the two screws (#708). Screw (#708) ×2 Inside finder LCD unit (#B1010) ・Connect Connect the FPC of the inside finder LCD unit (#B1010) to the connector on the penta prism FPC unit (#B1021). Penta prism FPC unit (#B1021) Inside finder LCD unit (#B1010) Metering FPC unit 1 ・Mount Mount the metering FPC unit (#B11008), and tighten the three screws (#607).
INC VBA23001-R.3762.A ・Attach Attach the penta prism box unit (B261RP) with the four screws (#642).
INC VBA23001-R.3762.A 3. Rear body Dust-proof tape ・Attach Attach the tapes {[TA0026 (8×50)], (8 #733, and #734)} based on the reference position. Tape [TA0026 (8×50)] Tape (#733) Drip-proof sponge ・Attach Attach the sponge (#751).
INC VBA23001-R.3762.A ・Attach Attach the two sponges (#753). ・Attach Attach the sponge (#766). ・Attach Attach the sponge (#761). Sponge (#753) ×2 Sponge (#761) Sponge (#766) Buzzer unit ・Peel off the backing paper of the buzzer unit (#1055), and attach [#1055]. The wires must not be placed on the stepped area. Solders must be positioned within the area specified by the arrow.
INC VBA23001-R.3762.A Eyelet ・Attach Attach the sponge (#762) to eyelet (#145). Sponge (#762) Eyelet (#145) ・Mount Mount the GND plate (#149). ・Mount Mount the eyelet (#145), and tighten the two screws (#614). GND plate (#149) Eyelet (#145) Screw (#614) ×2 ・Mount Mount the GND plate (#150). ・Attach Attach the sponges (#760 and #763). ・Mount Mount the eyelet (#146). ・Tighten Tighten the two screws (#614).
INC VBA23001-R.3762.A ・Attach Attach the GND plate (#106) by fitting with the boss. ・Tighten Tighten the screw (#683). GND plate (#106) Screw (#683) ・Arrange Arrange the wires (Orange/Black/Red) among the bosses as below. ・Mount Mount the GND plate (#107) by fitting with the bosses. ・Mount Mount the GND plate (#143) by fitting with the bosses.
INC VBA23001-R.3762.A ・Arrange Arrange the wires (back-side) (Orange/Black/Red) as below. ・Arrange Arrange the wires (bayonet-side) (Red/Black) as below. Back-side wire ×3(Orange/Black/Red) Bayonet-side wire ×2 (Red/Black) Battery contact spring ・Mount Mount the FG/ID contact spring (#80) and the two battery contact spring (#157) by fitting with the bosses. ・Tighten Tighten the three screws (#619).
INC VBA23001-R.3762.A Power drive PCB unit ・Mount Mount the GND plate (#142) by fitting with the bosses. GND plate (#142) ・Mount Mount the power drive PCB (#B1002) by fitting with the bosses. (Be careful not to pinch the wires.
INC VBA23001-R.3762.A ・Tighten Tighten the two screws (#683). ・Make Make the three solder bridges. ・Solder Solder the wires (Red/Black/Orange). Screw (#683) ×2 ・Mount Mount the OP FPC unit (#B1016), and tighten three screws [ROHS (#609)]. OP FPC unit (#B1016) Screw (ROHS) (#609) ×3 Bottom plate unit ・Attach Attach the GND plate (#140) to the bottom plate unit (#B67). ・Tighten Tighten the two screws (#617).
INC VBA23001-R.3762.A ・Attach the bottom plate unit (#B67) to the rear body, and engage the hook by fitting in the hole of the GND plate (#140). ・Tighten Tighten the four screws (#706) in numeric order. ④ ③ Screw (#706) ×4 ② Bottom plate unit (#B67) ① Hook GND plate (#140) Imaging power PCB unit ・Mount Mount the GND plate (#B141) by fitting with the bosses. ・Tighten Tighten the screw (#683).
INC VBA23001-R.3762.A ・Mount Mount the imaging power PCB unit (#B1029) and the shield plate (#B108) by the fitting with the bosses. ・Tighten Tighten the three screws (#683). Imaging power PCB unit (#B1029) Shield plate (#B108) Screw (#683) ×3 DC/DC PCB ・Mount Mount the GND plate (#110) by fitting with the bosses. ・Hook Hook the GND plate (#110), and tighten the two screws (#683).
INC VBA23001-R.3762.A ・Mount the DC/DC PCB (#B1030) by connecting its back to the connector. Connector DC/DC PCB (#B1030) ・Tighten Tighten the screw (#683). ・Solder Solder the wires (Red/Black/Green). ・Arrange the wires so as not to be placed on the protruding portions.
INC VBA23001-R.3762.A ・Mount Mount the GND plate unit (#B109) by fitting with the bosses. GND plate unit (#B109) Be careful not to pinch the wires. ・Tighten Tighten the two screws (#683).
INC VBA23001-R.3762.A SB/IF PCB unit ・Attach the gasket (#77, #83, and #473) along the outside rim of each connector. (#77) (#83) (#473) ・Mount Mount the SB/IF PCB unit (#B1041) by fitting with the bosses. (The FPC must be placed over the coil as below.)) Coil ・Tighten Tighten the two screws (#612). ・Solder Solder the wires (Red/Black/Orange).
INC VBA23001-R.3762.A 4 ����������������������������������� .Mounting Front body on Rear body. ・Peel off the backing paper of the dust-proof tape of the rear body. ・Mount the front body on the rear body. ・Tighten Tighten the two screws (#615), the four screws (#706) and the two screws (#702) in each numeric order.. (#706) ×4 ① ② ④ ③ ② ① ① (#702) ×2 ② (#615) ×2 Eyepiece mold ・Attach Attach the sponge (#779), the eyepiece mold (#291), and the sponge (#752). ・Tighten Tighten the two screws (#615).
INC VBA23001-R.3762.A Inspection and Adjustment of Body back ・"0" positioning of the dial gauge Turn counterclockwise by 0.18mm Turn counterclockwise by 0.18mm Surface plate "0" position of D90 (1) Mount the tool (J18001-1) on the surface plate as above, then set the dial gauge to "0". (2) From "0" position of (1), turn the index circle in the direction of the arrow so that the needle is on 18 (0.18mm) position. (This position is "0" position of D90.
INC VBA23001-R.3762.A ・ Measure six places from the bayonet face to the image PCB attaching face. ○ mark: to be measured Standard: 48.49±0.015mm / Parallelism: 0.015mm or less ・ In case the result is out of standard, make an adjustment by putting the washers between the front body and the rear body. Note: For some bodies, the washer(s) is/are already put on the attaching face of the image PCB . There is a red mark indication at the following three positions. 1.
INC VBA23001-R.3762.A ・Fit the mount GND wires (Black/Gray) in the side hook. ・Make Make the two solder brides on the power drive PCB (#B1002). ・Solder Solder the wires (Black/Red) of the SQ motor. ・Solder Solder the wires (Black/Gray) of the mount GND. ・Solder Solder the wires (Black) of the buzzer unit. Solder bridge ×2 Wire ×2 (Black/Gray) of mount GND Wire ×2 (Black/Red) of SQ motor Wires (Black) of buzzer unit.
INC VBA23001-R.3762.A Main PCB ・Mount the main PCB (#1001) by connecting the connectors. ・Place the FPC in the clearance between the PCB and rear body. ・Tighten Tighten the two screws (#640).
INC VBA23001-R.3762.A ・Fit the front body FPC wires (Red/Black) in the side hook. ・Connect Connect the five FPCs to the connectors. ・Solder Solder the wires (Red/Black) of the front body FPC. Wire×2 (Red/Black) of the front body FPC.
INC VBA23001-R.3762.A Mount the main condenser ・Attach Attach the main condenser unit (#B42) by fitting with the bosses. Main condenser unit (#B42) ・Tighten Tighten the screw (#683). ・Solder Solder the wires (Red/Black).
INC VBA23001-R.3762.A 5.���������� Top cover ・Attach Attach the double-stick tape (#338) and the LCD window (#335). ・Apply Apply the adhesive (super Ｘ ) to the remote control window (#463), and mount the remote control window (#463). ・Apply Apply the adhesive (super Ｘ ) to AF assist lamp protector (#326), and mount the AF assist lamp protector (#326).
INC VBA23001-R.3762.A Microphone ・Attach Attach the double-stick tape (#464) to the microphone (#1051). ・Mount Mount the microphone (#1051), and attach the tape [TA0009 (6×6)]. (6 Double-stick tape (#464) Microphone (#1051) Tape [TA0009 (6×6)] Mode dial ・Mount Mount the mode dial (#451). ・Mount Mount the click spring (#453) and the contact brush (#452) by fitting with the bosses. ・Tighten Tighten the screw (#640). ・Attach Attach the mode dial cap (#460) with the double-stick tape [TA0026 (8×8)].
INC VBA23001-R.3762.A Delete button ・Attach Attach the button (#398) and the conducting rubber (#399). Conducting rubber (#399) Button (#398) M/D FPC unit ・Mount Mount the M/D FPC unit (#B2455) by fitting with the bosses and fitting the end of lever into the hole of the top cover. Grease: ：PL- (Viewed Viewed from the back） M/D FPC unit (#B2455) ・Tighten Tighten the three screws (#640) in numeric order ( ①→②→③ →②→③ ②→③ →③ ③ ).
INC VBA23001-R.3762.A Remote control unit ・Attach Attach the remote control unit (#B1056) by fitting with bosses, and tighten the screw (#607). Screw (#607) Direction for positioning Remote control unit (#B1056) ・Make the three solders. olders.
INC VBA23001-R.3762.A SB lower control unit ・Attach Attach the flash pop-up arm A (#B341) to the SB lower control unit (#B2302). ・Attach Attach the flash pop-up arm B (#B342) to the top cover. ・By pulling both sides of [#B2302] outwards, assemble it in numeric order. Grease: GN-20SB Apply to the overall inner surface. Grease: CFD-409Z Apply to the overall inner surface.
INC VBA23001-R.3762.A ・Hook Hook the spring (#305). Spring (#305) ・Tighten Tighten the screw (#650). Screw (#650) ・Pass the two wires each in the following order through the hole of the roller (#308). ① Black (Thick)/Pink, ② Orange/Blue, ③ Black (Thin)/Red, and ④ Yellow/Brown.
INC VBA23001-R.3762.A Ｅ ・Arrange Arrange the wires by fitting with the bosses as below. SB upper cover ・Mount Mount the SB upper cover (#301), and tighten the two screws (#629).
INC VBA23001-R.3762.A Hot shoe ・Mount Mount the shoe mold unit (#B317), hot shoe (#316) and hot shoe spring (#318). ・Attach Attach the holder (#321) and the GND plate (#322). ・Tighten Tighten the four screws (#654) in numeric order as below.
INC VBA23001-R.3762.A Power dial ・Attach Attach the release button unit (#B350) from outside, and hook the spring (#346). ・Attach Attach the sheet (#352). Release button unit (#B350) Spring (#346) Oil barrier: NKS-401H Sheet (#352) ・Attach Attach the click spring (#347) and the contact brush (#348). ・Tighten Tighten the two screws (#602).
INC VBA23001-R.3762.A Top cover grip button ・Mount Mount the button (#339). Button (#339) AE-L button ・Attach Attach the button (#381) and conducting rubber (#397).
INC VBA23001-R.3762.A Top cover FPC unit ・Mount Mount the reflection sheet (#334) and the light guide (#333) to the top cover FPC unit (#B1007RP). ・Position the two conducting rubber (#332) in the direction of the red arrows, and attach them. ・Position the upper LCD (#1044) in the direction of the blue arrows, and mount them. ・Mount Mount the plate (#331) by engaging the four hooks of the top cover FPC unit (#B1007RP).
INC VBA23001-R.3762.A ・Mount Mount the top cover FPC unit (#B1007RP) by fitting with the boss. Top cover FPC unit (#B1007RP) Boss hole at back ・Mount Mount the arrangement plate (#340), and tighten the screw (#612). ・Tighten Tighten the three screws (#612) (which are for the top cover FPC unit) in numeric order ( ①→②→③ →②→③ ②→③ →③ ③). ・Tighten Tighten the screw (#605). ・Tighten Tighten the screw (#607).
INC VBA23001-R.3762.A Mount the MC/D unit (#B367) and the SC/D unit (#B377) by fitting with the bosses. SC/D unit(#B377) Boss hole at back MC/D unit (#B367) ・Tighten Tighten the four screws (#635), and make six solders.
INC VBA23001-R.3762.A ・Arrange Arrange the wires as below. ・Connect Connect the connector. ・Solder the five contacts of the shoe mold unit (#B317). ・Solder Solder the wires (Brown/Yellow). ・Solder Solder the wires (Red/Black).
INC VBA23001-R.3762.A AF assist lamp unit ・Mount Mount the AF assist lamp unit (#B325) by fitting with the bosses, and tighten the screw (#611). ・Solder Solder the two wires (Black).
INC VBA23001-R.3762.A Mount the top cover on the body A75 △（Revision） (Refer to Page A69 for "Inspection and adjustment of AE-CCD position".) ・Push Push the wires (four SB wires and two microphone wires) of the top cover unit (#B23RP) to the bayonet side. ・Connect Connect the FPC of the top cover unit (#B23RP). ・Attach Attach the microphone (#1051) by fitting in the cutout. ・Attach Attach the tape [TA0005 (6×10)] (6 to fix the microphone lead wires.
INC VBA23001-R.3762.A ・Tighten Tighten the two screws (#677). ・Tighten Tighten the two screws (#657). △（Revision） Screw ×2 (#677) Screw ×2 (#657) Screw ×2 (#657) ・Tighten Tighten the screw (#636). Screw(#636) ・Attach Attach the roller (#281) to the top cover. ・Attach Attach the sponge (#287) to the diopter adj knob (#282). ・Tighten Tighten the screw (#288). ・Attach Attach the diopter adj knob cover (#280).
INC VBA23001-R.3762.A ・Solder Solder the wires (Blue/Green/Yellow) of the preview SW unit. ・Solder Solder the wires (Red/Black) of the main condenser. ・Arrange Arrange the wires by fitting with the bosses. Wire ×3 (Blue/Green/Yellow) Wire ×2 (Red/Black) ・Solder Solder the wires (Black/Pink/Orange/Blue) of the SB. ・Attach Attach the tape (#831).
INC VBA23001-R.3762.A I/F cover ・Attach Attach the tape (#755) to the IF cover (#B28). I/F cover (#B28) Tape (#755) ・Push Push the wires of microphone to sides carefully not to pinch the wires. ・Mount Mount the IF cover (#B28). ・Mount Mount the IF cover (#71) and the cable release cover (#70). I/F cover (#B28) I/F cover (#71) Cable release cover (#70) Changed page △×１ - A72 ･ D90 A69 △（Revision） October. 2.
INC VBA23001-R.3762.A Grip rubber unit ・Attach Attach the grip red mold (#29) to grip rubber unit (#B26). ・Attach Attach the spring (#161) from behind, and tighten the screw (#638). ・Attach Attach the button (#390) and the conducting rubber (#389). ・Attach Attach the plate (#388). ・Adhere Adhere the tape (#811). ・Adhere Adhere the tape [TA0005 (3.3 × 11)]. Plate (#388) Conducting rubber (#389) Tape (#811) Button (#390) Screw (#638) Spring (#161) Grip rubber unit (#B26) Tape [TA0005 (3.
INC VBA23001-R.3762.A Front cover unit ・Attach the button (#391) and the button (#392) to front cover unit. ・Attach Attach the snap ring (#387) from behind. ・Attach Attach the spring (#201) and the button (#229). ・Attach Attach the E-ring (#722) from behind. Button (#391) Snap ring (#387) Button (#392) Front cover unit (#B24) Front cover E-ring (#722) Spring (#201) Button (#229) ・Mount Mount the front cover unit. (When mounted, the GND plate (#140) must not be placed on the front cover.
INC VBA23001-R.3762.A ・Tighten Tighten the two screws each (#613 and #611). Screw ×2 (#613) Screw ×2 (#611) A/M cover plate ・Attach Attach the A/M select lever (#121), and tighten the screw (#659). ・Mount the A/M cover plate (black) (#124) to be positioned for pointing to indexes correctly. A/M select lever (#121) Changed page △×１ Screw (#659) - A75 ･ D90 A72 △（Revision） A/M cover plate (black) (#124) October. 2.
INC VBA23001-R.3762.A Image sensor unit ・Position the image sensor unit (#B1051) in the direction of the red arrow, and mount them. Then, tighten the three screws (#680) in numeric order. Caution: Some bodies have lumirror sheets (#62) and washers (#63) already attached. (ref. Page A46) 46) Image sensor unit (#B1051) (#63) (#62) Screw ×3 (#680) ① ② Direction for positioning ③ ・Solder Solder the wires (Red/Black/Orange/Gray).
INC VBA23001-R.3762.A DG PCB unit ・Connect Connect the connector of the microphone. ・Attach Attach the gaskets (#480, #481 and #487). 0.5mm～1mm (#481) 481貼付け位置 0.5mm～1mm 487 基準に合わせ谷折 しながら貼付ける (#487) Attach by fitting with コネクタ部に 合わせて貼り付ける the connector section. The gasket must not touch the inclination sensor. 傾斜ｾﾝｻｰにかか っていないこと (#480) Closeup:基準部拡大図 reference position ・Mount Mount the DG PCB unit (#B1031) by fitting with bosses. ・Tighten the two screws (#683).
INC VBA23001-R.3762.A Inspection and adjustment of AE CCD positioning ! WARNING There are high voltege parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. ＊ Under the environment where the AE-CCD positioning is adjusted, use the reference body and confirm results.
INC VBA23001-R.3762.A Reference→ Reference screw X direction → a: screw Y direction → b: screw X direction (a) Loosen Adhesive: Screwlock #B11008 Y direction (b) Loosen Metering FPC unit b:#514 X direction (a) Tighten a: #514 Y direction (b) Tighten Reference screw Discharge of main condenser ・From the both terminals of the main condenser, discharge electricity. 2KΩ/5W Inside of round hole Changed page △×１ - A70 ･ D90 A76 △（Revision） October. 2.
INC VBA23001-R.3762.A Battery check voltage inspection 〈RS232C connection〉 For measuring consumption current value with this camera, attach the battery tool (J61213), and arrange the wires as below. 7.40V － ＋ ＋ － Ａ Device J61213 POWER SUPPLY (10V 5A) Changed page △×１ BATTERY TOOL - A71 ･ D90 A77 △（Revision） October. 2.
INC VBA23001-R.3762.A DG shield plate ・Mount Mount the shield plate (#78) and the shield plate unit (#B79) carefully not to damage the clip. ・Tighten Tighten the six screws (#683). ・Connect Connect the FPC of the DG-PCB unit. Screw ×5 (#683) Screw ×1 (#683) Shield plate (#78) Shield plate unit (#B79) Speaker unit ・Mount Mount the speaker unit (#B45), and tighten the two screws (#612).
INC VBA23001-R.3762.A Accuracy inspection and adjustment (Camera body exc. Imaging) ★ : New tool Commercially available straight cable AC adapter: EH-5 USB cable: UC-E4 Stabilized power supply Set value ＝ 7.4V 0.3Ω or AC adapter EH-5 To RS232C terminal 5.0A J65216 ★ D90 inspection and adjustment software Battery tool J61213 Use [9pin-25pin] conversion connector for a computer with 9-pin RS-232C terminal. RJ is not available, so use a commercial item.
INC VBA23001-R.3762.A D90 Inspection and Adjustment Software (J65119) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. Check the following operating environment which is required for installing this program on PC.
INC VBA23001-R.3762.A Because this is the self-extracting file, decompress the file before installing, and follow the next procedure. 1. Create a folder for installation under any drive and name. C: ￥DeskTopLauncher\D-SLR\D90 2. Paste the file (PD90.EXE) in the created folder. 3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts.
INC VBA23001-R.3762.A 4. When the decompression of file is finished, the file (D90.exe) is created. 5. The install is completed. 【Start-up of Program】 1. When "D90．EXE" is started, the following window will appear. So type in the user key. (ref. TIE07023) Caution: Once the user key is typed, from the next time, the adjustment screen will appear from the beginning. 2．Then the following window will appear. Click "OK".
INC VBA23001-R.3762.A 3．Click "OK". Program will start. 4. To display in Japanese, select the radio button of "Japanese" in "Language" at the lower right corner of the screen. However, the screen will not be displayed correctly by English OS. 5．To end the program, click "Close (×）" button at the top right hand corner of the screen or click "Quit". ※ When the camera body (excluding imaging) is inspected and adjusted, the USB connection will be reset in the process of writing the data into the camera.
INC VBA23001-R.3762.A Procedure for installing USB driver If this program is used by the USB interface, installing the USB driver is necessary. But if the OS is "Windows XP", the driver is already preloaded so it is not necessary to install it. (1) Connect the camera and PC by USB cable. Turn camera ON. (2) When "Add New Hardware Wizard" is displayed, click "Next". (3) Select "Search for a better drive than the one your device is using now. (Recommended)", and click "Next".
INC VBA23001-R.3762.A (5) Confirm that the driver is located at the right place, and click "Next". (6) Click "Finish". (7) Reboot the PC to complete the installation.
INC VBA23001-R.3762.
INC VBA23001-R.3762.A AE inspection and adjustment Inspection and Adjustment for AE ACCURACY When MAin PCB is replaced. When MAin PCB is not replaced. Writing in Initial values. Inspection and Adjustment for AE CCD POSITION. Inspection and Adjustment for AE SENSOR . Inspection and Adjustment for AE ACCURACY. Inspection and Adjustment for APERTURE CONTROL ACCURACY. Inspection and Adjustment for BUILT-IN SB LIGHT VOLUME . Adjustment for Battery Level Check. All the adjustments will be made sequentially.
INC VBA23001-R.3762.A ③ Inspection/adjustment of AE accuracy《USB communication》 Caution: Regarding AE accuracy, inspection is not made by using exposure value with shutter tester as seen in the traditional method. The metering value will appear on PC screen. Whenever the metering FPC unit is disassembled/replaced or the main PCB is replaced, make this adjustment. Device J18267 J19123 LENS AF50/1.4D SHUTTER TESTER EF-1(CE) LENS AF28/2.8D LENS AF70-300/4-5.6D OR LENS AF-SVR70-300/4.5-5.
INC VBA23001-R.3762.A AF inspection and adjustment Caution: When this adjustment software is used for the first time, prepare three D90 cameras, and measure by "Writing of AF adj. lens offset value" on the main menu. ① AF accuracy adjustment (All the adjustments items will be made in order.) Caution: Whenever the AF sensor unit is disassembled/replaced or the main PCB is replaced, make this adjustment.
INC VBA23001-R.3762.A ③ LARK adjustment (incl. CCD output adjustment)《USB communication》 Device J18267 J63070 LENS HOLDER LENS AF50/1.4D COLOR VIEWER J15259 AF ADJUSTING TOOL J15280 J18266 J15264 Z ADJUSTMENT LENS (FOR 1m) ILLUMINATION BOX FOR AF ADJUSTMENT J18344 MULTI CAM 2000 AF CHART ④ AF shift adjustment《USB communication》 Device J18393 J19124 Z-LIGHT SLANT CHART Changed page (Overall revision) - A90 ･ D90 - J18267 LENS AF50/1.4D October. 2.
INC VBA23001-R.3762.A 6.Back cover ・Attach Attach the double-stick tape (#403). ・Attach Attach the TFT monitor cover (#402). Double-stick tape (#403) TFT monitor cover (#402) Back cover (#401) ・Attach Attach the two sponges each (#404 and #405). (#405) (#404) (#404) (#405) ・Attach Attach the rubber (#433). ・Attach Attach the drip proof sheet (#44).
INC VBA23001-R.3762.A SD cover unit ・Attach Attach the label (#436). Label (#436) ・Mount Mount the SD cover unit (#B431) by fitting the end of spring into the hole of the body and fitting with the bosses. ・Tighten Tighten the two screws (#621).
INC VBA23001-R.3762.A Button / SW ・Attach Attach the selector lock lever (#416). ・Attach Attach the selector SW unit (#B420). ・Tighten Tighten the screw (ROHS) (#707). ・Attach Attach the multi selector (#412). ・Attach Attach the button (#414). ・Attach Attach the conducting rubber (#413). Multi selector (#412) Button (#414) Selector lock lever (#416) Conducting rubber (#413) Grease: GN-20SB Selector SW unit (#B420) Screw (ROHS) (#707) ・Attach Attach the button (#421) by fitting with the bosses.
INC VBA23001-R.3762.A TFT monitor ・Mount Mount the TFT monitor (#1057). ・Mount Mount the plate (#406). ・Tighten Tighten the screw (#710).
INC VBA23001-R.3762.A Rear display FPC unit ・Attach Attach the double-stick tape (#423) to the back of the plate (#415). #423 ・Peel off the backing paper of [#423], and adhere it to the rear display FPC unit (#B1034) as below.
INC VBA23001-R.3762.A ・Mount Mount [#B1034] by fitting with the bosses.
INC VBA23001-R.3762.A ・Mount Mount the plate (#422). Rear display FPC unit (#B1034) Plate (#415) Plate (#422) ・Tighten Tighten the three screws (#710) in numeric order（①→②→③）. （①→②→③）. →②→③）. ②→③）. →③）. ③）. ）..
INC VBA23001-R.3762.A ・Tighten Tighten the four screws (#670) and the six screws (#670) in numeric order as below. ・Connect Connect the connector.
INC VBA23001-R.3762.A ・Attach Attach the gasket (#483). ・Attach Attach the tape [TA0005 (12.5×12.5)]. (12.5 Gasket (#483) Tape [TA0005 (12.5 ×12.5)] ・Attach Attach the SD access lamp window (#408). ・Attach Attach the double-stick tape (#409) and the cover rubber (#407).
INC VBA23001-R.3762.A Mounting of Back cover ・Connect Connect the FPCs of the back cover to the connectors on the DG PCB. ・Mount Mount the back cover carefully not to pinch the FPCs. 7. External area ・Tighten Tighten the four screws (#657). ・Tighten Tighten the two screws (#608).
INC VBA23001-R.3762.A Bottom cover ・Mount Mount the bottom cover unit (#25). ・Tighten Tighten the two screws (#657), two screws (#658), one screw (#661), and two screws (#692) in numeric order as below. ・Tilt Tilt the battery chamber unit (#B151) at a 35-degree angle, and attach it.
INC VBA23001-R.3762.A Shooting-image Adjustment 1. Summary A103 △（Revision） When the D90 shooting image-related and listed parts on Page A104 are replaced, be sure to make this adjustment by the shooting image adjustment software for D90 (J65127). Use the D90 reference body beforehand, and get the reference value. Getting reference value will create the reference data "D90BSD.DAT" automatically. Make all of the adjustment items in numeric order.
INC VBA23001-R.3762.A 3. Hardware requirements OS： Windows2000, WindowsXP, Windows VISTA Japanese or English OS PC： CPU Pentium Ⅱ or more Memory 256MB or more USB1.1 or 2.0 Screen size: 1024×768 pixels or more 4. How to set up Create "C:\DeskTopLauncher\D-SLR\D90IMGIMG" folder is created in the hard disc of PC, so copy "PD90IMG.EXE". This file is an self-extracting file, so decompress it in the created folder. ※ Be sure to copy the above file in the same directory.
INC VBA23001-R.3762.A Image adjustment ① Gr/Gb compensation adjustment (G filter) Camera is faced to the light-emitting box (color viewer) of LV13 equiv. with SP2 (G filter) being put between them. G-line crawl (3895×2610 pixels) is divided into (29×25) blocks, and the adjustment is made so that the difference between Gr and Gb output can fall in the standard range.
INC VBA23001-R.3762.A ④ Shading adjustment The camera is faced to the color viewer (LV13 equiv.) with ND filter (-4 steps) being put between them. The adjustment of white balance distribution is made for 3 areas [Area ① : Central 1936×1926-pixel area; Area ② : All the divided areas except ③ -areas after dividing (3890×2606-pixels) into (29×25-pixels); Area ③ ; 4 corners of (4×6-pixels) after dividing (3890×2606-pixel) into (29×25-pixels)].
INC VBA23001-R.3762.A ⑥ Sensitivity ratio adjustment Using the shutter tester (LV9 equiv.) and tool lens (F5.6), the adjustment is made so that the R/G, B/G output becomes the same as the output ratio of the sensitivity ratio reference value that was calculated by the reference body. The adjustment is made only under the condition of ISO200, and the average value of (425 pixels × 425 pixels) which was deviated from the center by 425 pixels is used.
INC VBA23001-R.3762.A ⑩ TFT adjustment Flickering, color and luminance of TFT are adjusted. ※ Whenever the DG-PCB or TFT monitor are replaced, be sure to perform "WRITING THE TFT FIXED VALUE." Hue adjustment Usually default value is set and adjustment is not necessary. If some problem is found with hue by visual check, adjust and correct it by "+/-" button. Brightness adjustment Usually default value is set and adjustment is not necessary.
INC VBA23001-R.3762.A ⑫ Initial settings (Factory default settings) This restores factory default settings. Select the language and video mode. Because this setting of RP DG-PCB is blank, be sure to set the initial default setting when the DG-PCB is replaced. ⑬ Confirm data Saving/restoring of the system fixed values, image register, TFT register, EEPROM1, 2, 3. The functions of saving/restoring each data is for sending backup data to Service Planning for analysis, if some problem occurs. ⑭ Version No.
INC VBA23001-R.3762.A ∞ Infinity focus inspection & adjustment ・Replace the finder screen with the infinity focus check screen (J18394), and use the reference lens (J18010) and read the value. In case it is out of standard, increase or decrease washers (#266 selected from A to C) for adjustments. * Supply the power (Battery or EH-5) for checking. Caution: When [J18394] is put in to replace the finder screen, put it with the silver spacers upward, which are attached on both sides.
INC VBA23001-R.3762.A ＜ Measurement of Consumption current value ＞ When this camera is used for measuring the consumption current value, connect the battery tool (J61213), and turn the change-SW to OFF. Then make measurements based on the following. 7.8V 0.3Ω － ＋ ＋ － Ａ Turn change-SW to OFF. 《Inspection standards》 Main SW / OFF Test item Standard All operational buttons are NOT pushed. Main SW / ON (Half-release timer OFF) 250μA or less ref. above.
INC VBA23001-R.3762.A Cleaning between Penta prism and SI-LCD 《In case of cleaning by NOT removing the screen box》 ・Take out the two screws (#689), and remove the mirror receiving part. #689×2 ・Release the claw (indicated by the arrow) of the Screen box screen box retaining plate (#511), and lower [#511]. #511 ・Pull the screen box section down straightforward until the position shown in the picture. ＊ Do NOT pull down with force because the FPC is connected.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.A ﾊﾟﾜｰﾄﾞﾗｲﾌﾞ PCB （表） POWER DRIVE PCB (Surf face) ヒューズ FUSE IS460-012 ﾊﾟﾜｰﾄﾞﾗｲﾌﾞ PCB （裏） POWER DRIVE PCB (Reverse face) ヒューズ FUSE IS460-012 Phenomenon when FUSE has blown out. Camera can NOT be powered by battery (BUT by AC adapter). Camera can NOT be powered by AC adapter (BUT by battery).
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.A SB 基板（表） SB PCB (Surf face) ヒューズ FUSE IS460-012 Phenomenon when FUSE has blown out. Speedlight can NOT be charged. Shutter can NOT be released.
INC VBA23001-R.3762.A SB/IF 基板部組 SB/IF PCB UNIT ヒューズ IS460-012 Phenomenon when FUSE has blown out. Camera can NOT be powered by AC adapter (BUT by battery).
INC VBA23001-R.3762.
INC VBA23001-R.3762.
INC VBA23001-R.3762.A Inspection standards Items Judgment standard Remarks External view Step Btwn top cover & apron: 0.2 mm or less Visual check (height difference) Other parts: Digital micrometer 0.3 mm or less Moving parts: 0.5 mm or less Gap Btwn Top cover & Apron, I/F cover , back cover : 0.2 mm or less Visual check Btwn Top cover & Apron, I/F cover : 0.2 mm or less Thickness gauge SB case & Top cover; SB case & Apron (when built-in speedlight is stored) : 0.3 mm or less Other parts: 0.
INC VBA23001-R.3762.A Items Judgment standard Remarks AF accuracy Yaw Center：± 4 mrad PC Others: ± 10 mrad Special tool Brightness box Pitch Center：± 5 mrad Others: ± 11 mrad Block Def amount Others than Side: 0 ± 50 μm Side: 0 ± 75 μm AF-assist illuminator Lighting level AF50/1.4D Range from EV5.2 to 6.2 Brightness box 1/4000 ※：0.2±0.65EV AF50/1.4D（∞） Speed at less than 1/4000 ～ 1/2000 or More：± 0.65EV Shutter SpeedTestr AE accuracy Exposure on image Lower SPeed at less than 1/2000:±0.
INC VBA23001-R.3762.A Items Judgment standard Remarks Viewfinder Inner LCD lower panel Up-down position: No outstanding misalignment Visual check window position Tilt: １° or less AF50/1.4D, F5.6 Looking through Finder field frame Lens vignetting/distortion: No outstanding vignetting/distortion viewfinder, measure Tilt: (based on Bottom cover): 90°± 30’ a tilt of indication Relative angle to image sernsor : 0.
INC VBA23001-R.3762.A Items Operation time / consumption current Judgment standard Lens scan Constant Voltage AF50/1.8 accumulated Remarks Operation time: 1000 ms or less Consumption current accumulated: 500 mAsec or less Poewr Source 7.8 ＋ 0.3Ω LV12 AF70-210/4-5.6D Operation time: 2000 ms or less Oscilloscope Consumption current accumulated: 800 mAsec or less Preview (AF50/1.
INC VBA23001-R.3762.A Items Resolution Judgment standard Remarks Judgment method AFS80-200mm/F2.8D When TIFF/JPEG recorded: 105mm Take a shot by matching the angle of view of the chart’s vertical F5.6 direction. AE: M mode Adjust the speed so that brightness becomes 220 ± 5LSB (8bit) at Image size: L white part about the center of chart.
INC VBA23001-R.3762.A Items TFT unit Point defect Judgment standard Remarks Luminescent pixels: 3 or less (G ＝ 0, Others than "G" ≦ 1 in "A" section) There must not be 2 consecutive defective pixels. Black pixels: 3 or less (1 or less in "A" section) There must not be 2 consecutive defective pixels. Total of luminescent pixels and black pixels: 3 or less (1 or less in "A" area） A : 19.08×25.44mm A': 38.16×50.
INC VBA23001-R.3762.A 工具・ＴＯＯＬＳ ※：新規設定工具・NEW TOOL 工具番号 Tool No.
INC VBA23001-R.3762.A ※：新規設定工具・NEW TOOL 工具番号 Tool No. 名 称 Name of tool 備 考 Others J18267 ＡＦ５０／１．４Ｄ LENS AF50/1.
INC VBA23001-R.3762.A ※：新規設定工具・NEW TOOL 工具番号 名 Tool No.
INC VBA23001-R.3762.A ※：新規設定工具・NEW TOOL 工具番号 Tool No.
