DS00329BCN-MSU140-1.
DS00329BCN-MSU140-1.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 2 S Y S T E M U N I T Features and Benefits The MSU140 offers a number of improvements over other IR Extender Main System Units: • Universal system—compatible with virtually all brands of A/V equipment and remote controls. • Accommodates one IR sensor or keypad. • Provides four flasher outputs via convenient 3.5mm jacks. • System feedback LED confirms operation. • 3-30V AC/DC status input.
DS00329BCN-MSU140-1.
DS00329BCN-MSU140-1.qxp I N F R 8/17/05 A R E 11:26 AM M D A I Page 4 S N Y S T E M U N I T MSU140 Parts Guide 1 3 2 POWER 1 2 3 4 +12V DC FLASHER OUTPUTS 4 3-30V AC/DC STATUS IN MSU140 IR MAIN SYSTEM UNIT INPUT 1 5 1. 12V DC Jack – Provides 12 volt DC power to MSU via a regulated power supply. 2. IR Flasher Outputs – 3.5mm jacks provide output for either single or dual (MF1, MF2, MF1VF, MF2VF) low-level flashers. 3. 3-30V AC/DC Status – 3.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E 11:26 AM M D A I Page 5 S N Y S T E M U N I T Installation Considerations IMPORTANT Do not place the MSU140 on top of or directly behind a television set. Some television sets produce intense electromagnetic interference which may disable your IR extender system. Placement of the MSU140 Place the MSU140 conveniently close to the equipment it will be controlling.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 6 S Y S T E M Wiring From every IR Sensor location you must “home-run” a category 5 cable back to the MSU140. Home run means that an individual cable is connected between each IR Sensor and the MSU140. See Figure 4. U N I T “TECH TIP” Remotely Located IR Sensor Figure 4: Home run the sensor cable from the sensor to the MSU140.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 7 S Y S T E M U N I T Intellipad Wiring When you are placing both a Intellipad and a sensor (or two keypads) in one room you may “daisy-chain” using a single cable. A cable is run between the keypad and the sensor and a single cable is run from the sensor back to the MSU140. To prevent data feedback an IN4003 Blocking Diode is inserted on the data (IR) line between the Intellipad and the sensor.
DS00329BCN-MSU140-1.qxp I N F R 8/17/05 A R E 11:26 AM M D A I N Page 8 S Y S T E M Sensor/Keypad Cable The MSU140 connects to IR sensors and the Intellipad with category 5 cable, with a maximum cable run of 500'. Flasher Cable Niles infrared flashers come supplied with a 10 foot 2-conductor 22 gauge cable. Should you need to extend it, use a 16 gauge 2-conductor cable (“zip-cord”). Shielding is not necessary for a flasher. Flasher wires can be extended up to 200 feet.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 9 S Y S T E M U N I T STEP DESCRIPTION 1. Connect and test the power supply. If it tests OK, unplug the connector from the power socket and proceed. A) Plug the supplied 12vDC power supply into an unswitched 120V AC outlet, 50-60 HZ . B) Plug the connector into the socket marked “Power” on the MSU140. C) If the Power LED does not light, test the unswitched 120 VAC outlet, 50-60 HZ with another appliance.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 10 S Y S T E M U N I T STEP DESCRIPTION 3. Test for shorts and interference. A) Reconnect the power supply. If the Power LED lights and the IR Test LED stays off, unplug the connector from the power socket and proceed to Step 4.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 11 S Y S T E M U N I T Testing the IR Extender System Test your IR Extender system by following these three principal guidelines: 1. All components can be operated. Test all of your remote controls for all of your equipment. 2. Operation is consistent. A good test is to repeatedly step from Pause to Play with your VCR, CD, DVD, or Tape player remote control.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 12 S Y S T E M U N I T Power Status — Introduction To properly wire an Intellipad to the MSU140, refer to Figure 5. By providing 3-30V AC/DC to the status input jack of your MSU140 you can send a status signal to sensors or an IntelliPad without running any additional wiring. Built into the MSU140 is a Niles status signal generator.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 13 S Y S T E M U N I T Power Status — Installation Considerations Proper Power Supply If status is being supplied from a switched outlet you must connect a Niles 12vDC wall adapter (Niles FG01035) into the switched AC power outlet of the preamp/receiver in your system. Any 12vDC power supply with a minimum of 100mA current capacity can be substituted.
DS00329BCN-MSU140-1.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 15 S Y S T E M U N I T Troubleshooting Guidelines There are three basic problems which prevent proper operation. In the order of probability the problems are: 1.– Bad Connections or Wiring If the connections or wiring are wrong, loose, shorted or open the system will not operate properly.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I N Page 16 S Y S T E M U N I T Solution: To eliminate EMI try the following methods: 1. Move the sensor or the sensor cable away from the EMI source or move the source of the EMI away from the sensor or the cable. 2. Connect the Sensor’s GND terminal to true earth ground (if this isn’t feasible use the main system unit’s GND terminal). 3.
DS00329BCN-MSU140-1.qxp I N F R A 8/17/05 R E D 11:26 AM M A I S Y S T E M U N I T Specifications Contents IR System MSU140 1 Compatible with virtually all brands of remotes using carrier frequencies between 26 and 105kHz. Screwless Connectors 1 In-line Power Supply 1 Wiring Requirements Self-Adhesive Rubber Feet 4 Individual home-runs of category 5 cable from each sensor/keypad.
DS00329BCN-MSU140-1.
DS00329BCN-MSU140-1.qxp 8/17/05 11:26 AM Page 19 Niles Audio Corporation www.nilesaudio.com 12331 S.W. 130 Street Miami, Florida, 33186 Tel: (305) 238-4373 Fax: (305) 238-0185 ©2005 Niles Audio Corporation. All rights reserved. Niles, the Niles logo, IntelliPad and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. MicroFlasher is a trademark of Niles Audio Corporation. Because we strive to improve our products.