I N S TA L L AT I O N G U I D E FOR USE WITH NILES SW10JM JOIST MOUNT SUBWOOFER A N D N I L E S S W 1 0 W M WA L L M O U N T S U B W O O F E R SW10JM SW10WM
CONGRATULATIONS! Thank you for choosing Niles. This manual is for use with the Niles SW10JM Joist Mount Subwoofer or the Niles SW10WM Wall Mount Subwoofer. The SW10JM/SW10WM are custominstall passive subwoofers designed to blend seamlessly within a home’s interior. Combined with the Niles SWA-500M subwoofer amplifier, the SW10JM/SW10WM provide superior sonic quality in home theater and home audio bass reinforcement.
INTRODUCTION The Niles SW10JM Joist Mount Subwoofer is designed to fit discreetly in ceiling joists or subfloors. The Niles SW10WM Wall Mount Subwoofer is designed to fit discreetly in walls. When properly installed, the SW10JM/SW10WM are virtually unnoticeable, visible only through the included Microperf™ ceiling grille or floor/wall grille. You’ll hear deep, thunderous bass and save floor space.
FEATURES AND BENEFITS 10-INCH WOOFER WITH INJECTION MOLDED TCC™ (SW10JM ONLY) The SW10JM features a 10” injection molded TCC (Talc, Carbon and Ceramic) cone and ported enclosure for maximum bass response. 10-INCH REINFORCED FIBERGLASS CONE WOOFER (SW10WM ONLY) The SW10WM features a 10” shallow-depth reinforced fiberglass cone woofer that is extremely rigid to reduce break up, lower distortion, and provide enhanced bass response.
QUALITY YOU CAN COUNT ON Since 1978, Niles Audio has been a leading manufacturer of custom-installed home entertainment products. Recognized around the world for designing and manufacturing reliable, durable, application specific products, Niles has more than 500 individual products for whole-house distribution and integration of audio/video systems, speakers, receivers, amplifiers, automation devices, controls, and accessories. The SW10JM/SW10WM were designed in the USA by Niles engineers.
TOOLS NEEDED: • Pencil • Drywall Saw • Phillips Screwdriver • Drill (and assorted Bits) • Qty. 2; 2 x 4s (48” in length) • Wire strippers • Tape Measure • Level (Optional) • Awl (optional) • Staple gun (optional) • Protective safety gear • Tools suitable for cutting opening in the applicable flooring/wall material CAUTION: ALWAYS CHECK FOR ELECTRICAL, HEATING, PLUMBING, CONDUIT, ETC., BEFORE CUTTING INTO CEILINGS OR FLOORS.
SW10JM PLACEMENT Before you begin, carefully plan the location of the SW10JM, keeping in mind that the SW10JM will be installed parallel with the rooms’ joist construction. For maximum bass performance, we recommend positioning the SW10JM so that the grille/vent is near a corner or sidewall and is as close to the main speakers as possible. Keep in mind that the SW10JM is not magneticallyshielded and could cause interference if placed near a video display.
SW10JM IN-CEILING/IN-FLOOR INSTALLATION The SW10JM subwoofer mounts directly to ceilings or sub-floors between joists and accommodates both 16" and 24" on-center joist construction. The included cardboard template matches the dimensions of the SW10JM and is used to position the subwoofer, the 2 X 4s that will support the subwoofer, and for marking the 4 pilot holes for cutting out an opening for the grille.
SW10JM INSTALLATION – FLOOR APPLICATION FLOOR APPLICATION – BEFORE FINAL FLOORING APPLIED Pre-Construction Floor 1. Use template to determine a suitable installation location. Place the SW10JM cardboard template in the desired location making sure the template is level and aligned correctly. You may want to staple the template in place for added ease. 2a. Measure the width between the joists/ studs and cut two 2 X 4’s to match this width. The 2 X 4’s will be used to cross brace between joists. 2b.
2x4 4. Attach the supplied front and rear brackets to the 2 x 4’s using the supplied 1.5" wood screws. NOTE: REMOVE THE STOP BLOCK FROM THE SW10JM PORT. THE STOP BLOCK IS INCLUDED TO PREVENT THE SUBWOOFER FROM DISENGAGING FROM BRACKETS UNTIL THE GRILLE IS INSTALLED. 2x4 Front Bracket Rear Bracket Screws 5. Place the SW10JM subwoofer into the brackets aligning the attachment pins to the slots in the brackets. Begin with the ported end first. Subwoofer Front Bracket Subwoofer Rear Bracket 6.
SW10JM INSTALLATION – FLOOR APPLICATION Floor (CONTINUED) 3" Screws 7. Install Trim Out Panel to protect cabinet from debris until trim out using the supplied screws. Cover Hole Cut-out 8. For trim out, remove Trim Out Panel. 9. Install the included floor grille into the cutout opening using the same screws from the Trim Out Panel. Floor 3" Screws Grille Hole Cut-out OPTIONAL: The grille can be painted to match most decors but should be painted before installation.
SW10JM INSTALLATION – FLOOR APPLICATION FLOOR APPLICATION – COMPLETE INSTALLATION New/Existing Construction Floor 1. Use template to determine a suitable installation location. Place the SW10JM cardboard template in the desired location making sure the template is level and aligned correctly. You may want to staple the template in place for added ease. Template 2a. Measure the width between the joists/studs and Template cut two 2 X 4s to match this width.
SW10JM INSTALLATION – FLOOR APPLICATION (CONTINUED) 2x4 4. Attach the supplied front and rear brackets to the 2 x 4’s using the supplied 1.5" screws. NOTE: REMOVE THE STOP BLOCK FROM THE SW10JM PORT. THE STOP BLOCK IS INCLUDED TO PREVENT THE SUBWOOFER FROM DISENGAGING FROM BRACKETS UNTIL THE GRILLE IS INSTALLED. 2x4 Front Bracket Rear Bracket Screws 5. Place the SW10JM subwoofer into the brackets aligning the attachment pins to the slots in the brackets. Begin with the ported end first.
7. Install the included floor grille into the cut-out opening using the supplied screws. OPTIONAL: The grille can be painted to match most decors but should be painted before installation. Additionally, paint the grille separately from the loudspeaker frame. For best results when painting the grille, use a spray gun or airless sprayer. Thin the paint to prevent clogging of the grille holes and apply several light coats instead of one heavy one.
SW10JM INSTALLATION – CEILING APPLICATION CEILING APPLICATION – BEFORE DRYWALL APPLIED Pre-Construction 1. Use template to determine a suitable installation location. Place the SW10JM cardboard template in the desired location making sure the template is level and aligned correctly. You may want to staple the template in place for added ease. Template 2a. Measure the width between the joists/studs and X Minimum cut two 2 X 4’s to match this width.
4. Place the SW10JM subwoofer into the brackets aligning the attachment pins to the slots in the brackets. Begin with the ported end first. Front Bracket Subwoofer Subwoofer Rear Bracket Screw Stop Block 5. Install the stop block between the bracket and cabinet at rear of cabinet as indicated in drawing. Screw Subwoofer Stop Block 6. Install Trim Out Panel to allow drywall installer exact location of cut-out.
SW10JM INSTALLATION – CEILING APPLICATION (CONTINUED) 7. For trim out, remove Trim Out Panel. Hole Cut-out Ceiling Cover 3" Screws 8. Install the included ceiling grille frame into the cut-out opening using the supplied screws. Hole Cut-out Ceiling Grille 3" Screws 9. Install the included ceiling grille into the frame. OPTIONAL: The grille can be painted to match most decors but should be painted before installation. Additionally, paint the grille separately from the loudspeaker frame.
SW10JM INSTALLATION – CEILING APPLICATION CEILING APPLICATION – COMPLETE INSTALLATION New/Existing Construction 1. Use template to determine a suitable installation location. Place the SW10JM cardboard template in the desired location making sure the template is level and aligned correctly. You may want to staple the template in place for added ease. 2a. Measure the width between the joists/studs and cut two 2 X 4’s to match this width. The 2 X 4’s will be used to cross brace between joists.
SW10JM INSTALLATION – CEILING APPLICATION (CONTINUED) Screws Rear Bracket Front Bracket 4. Attach the supplied front and rear brackets to the 2 x 4’s using the supplied 1.5" screws. 2x4 NOTE: REMOVE THE STOP BLOCK FROM THE SW10JM PORT THE STOP BLOCK IS INCLUDED TO PREVENT THE SUBWOOFER FROM DISENGAGING FROM BRACKETS UNTIL THE GRILLE IS INSTALLED. 2x4 5. Place the SW10JM subwoofer into the brackets aligning the attachment pins to the slots in the brackets. Begin with the ported end first.
7. Install the included ceiling grille into the cut-out opening using the supplied screws. Hole Cut-out Ceiling Grille 3" Screws 8. Install the included ceiling grille into the frame. OPTIONAL: The grille can be painted to match most decors but should be painted before installation. Additionally, paint the grille separately from the loudspeaker frame. For best results when painting the grille, use a spray gun or airless sprayer.
AMPLIFIER REQUIREMENTS & WIRING The SW10JM is a passive (non-powered) subwoofer and must be used with a power amplifier. We strongly recommend the Niles SWA-500 subwoofer amplifier. Use with any other amplifiers could result in less than optimal performance. Left & Right LineLevel Output Home Theater Receiver L Optional R SWA-500M Back 1st Subwoofer 2nd Subwoofer (Optional) Figure 3.
The SW10JM has 5-way binding posts that accept all types of wire ends. Figure 4. 5-way binding posts Be sure to wire the subwoofer “in-phase”— positive (red) terminal on the amplifier output must be connected to the corresponding positive (red) terminal on the subwoofer and likewise negative (black). Most speaker wires have markings along one or both conductors to help you make the correct connections. Take care to wire the subwoofer correctly in-phase, before floors/ceiling are sealed.
SW10WM (WALL MOUNT) SUBWOOFER The SW10WM Wall Mount subwoofer includes the following items: Preconstruction package: • 1 Ported cabinet (back box) with trim-out panel • 1 set of installation brackets with screws • 1 set of rubber feet Installation package: • 1 Baffle mounted passive driver • 1 MicroPerf™ grille with frame • 1 Template for subwoofer placement TOOLS NEEDED: • Pencil • Drywall saw Figure 5.
SW10WM PLACEMENT Before you begin, carefully plan the location of the SW10WM subwoofer, keeping in mind that the SW10WM will be installed parallel with the room’s stud construction. For maximum bass performance, we recommend positioning the SW10WM so that the grille/frame is near a corner or sidewall and is as close to the main speakers as possible. Keep in mind that the SW10WM subwoofer is not magnetically-shielded and could cause interference if placed near a video display.
SW10WM IN-WALL INSTALLATION The SW10WM subwoofer mounts parallel within the room’s standard 2 X 4 stud construction. The included cardboard template matches the dimensions of the SW10WM and is used to position the subwoofer. Be sure to mount the SW10WM securely, as the bass output could cause unwanted vibration if the SW10WM is able to move. Be sure the studs to which the SW10WM is mounted are securely braced so that the distance between them does not change and they are not able to move or shift.
2b. Determine suitable wire routing method. The SW10WM is provided with terminal cups at both the bottom and top of the unit for convenience. Top Bottom Preparing the cabinet 3a. Remove the large bolts located at the top of the cabinet and flip the brackets over re-installing brackets with the same bolts, leaving them loose. Ensure the flange surface with 4 holes is above the cabinet. Allow access for the installation hardware. 3b. Locate the feet inside the pre-construction package.
SW10WM IN-WALL INSTALLATION (CONTINUED) 5. Secure the brackets to the studs using the provided hardware. 6. Make necessary wire connections to terminal cups NOTE: THE SW10WM CABINET HAS THE NECESSARY TRIMOUT PANEL ALREADY INSTALLED. THIS WILL ALLOW SHEETROCK INSTALLERS THE EXACT LOCATION FOR CUTTING THE FRAME OPENING AND PREVENT DEBRIS FROM ENTERING THE CABINET DURING THE FINAL PHASES OF CONSTRUCTION. Installation Package 8. Remove Trim Out Panel from the cabinet and discard. 9.
12. Insert the frame into the cut-out hole securing the frame with the supplied 2" screws where needed to ensure a snug fit against the wall. 13. Insert the metal grille into the frame pressing firmly all the way around the perimeter. TIP. If the grille does not stay flush in some areas, remove grille, bending flange slightly outward in those areas, then re-apply grille to frame. OPTIONAL: The grille can be painted to match most decors but should be painted before installation.
AMPLIFIER REQUIREMENTS & WIRING The SW10WM is a passive (non-powered) subwoofer and must be used with a power amplifier. We strongly recommend the Niles SWA-500 subwoofer amplifier. Use with any other amplifiers could result in less than optimal performance. Figure 7. 1 or more SW10WM connected to the SWA-500 The SW10WM has two 5-way binding posts that accept all types of wire ends.
WIRING FOR NEW CONSTRUCTION For best results, avoid running speaker wire near AC wiring, as it may induce a 60Hz hum in the audio signal. It’s a good idea to run the speaker wire after the electrical wiring has already been completed, so that you can route the speaker wire at least three feet away from the electrical wiring. If speaker wire and AC wiring must run parallel, install the wire within a metal conduit. NOTE: THE SW10WM IS DESIGNED FOR INTERIOR INSTALLATIONS BETWEEN STANDARD STUD CONSTRUCTION.
TROUBLESHOOTING GUIDE If you experience a problem operating the SW10JM or SW10WM, consult this guide first. The most common problems relate to hook up. If the problem persists, or you have additional questions, call your local Niles dealer or Niles Technical Support at 1-800-289-4434, 305-238-4373 or techsupport@nilesaudio.com. Be sure to call from your telephone extension nearest the system. PROBLEM No Sound SOLUTIONS Short circuit or loose wire.
NOTES 30
NOTES NILES AUDIO CORPORATION – 1-800-BUY-HIFI or 1-305-238-4373 31
BLENDING HIGH FIDELITY AND ARCHITECTURE® Niles Audio Corporation 1 2 3 3 1 S . W. 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6 1-305-238-4373 1 - 8 0 0 - B U Y- H I F I – w w w. n i l e s a u d i o . c o m © 2 008 Niles Audio Corporatio n. All rights reser ved. Niles, the Niles logos and Blen d i n g H i g h F i d e l i t y a n d A r c h i t e c t u r e a r e registered trademarks of Niles Audio Corporation. TCC and MicroPerf are trade m a r k s o f N i l e s A u d i o C o r p o r a t i o n .
