I N S TA L L AT I O N G U I D E WALL-MOUNT IR SENSOR WS110R
CONGRATULATIONS! Thank you for choosing the WS110R Wall-Mount Infrared Remote Sensor from Niles. With proper installation and operation, you should enjoy years of trouble-free use. Niles manufactures the industry’s most complete line of custom installation components and accessories for audio/video systems. To see the complete Niles product assortment, visit us on the internet at: www.nilesaudio.com.
INTRODUCTION The Niles WS110R is a wall-mount, Decora® style IR sensor designed for use with the Niles infrared extender systems. Installed in a remote room location, the WS110R receives the IR commands transmitted from your existing hand-held remotes in that room. The commands are carried via a CAT 5 cable to your A/V equipment in another room, and instantly “repeated”. The WS110R is compatible with all current Niles infrared systems.
FEATURES AND BENEFITS The WS110R offers a number of improvements over other wall-mount IR sensors.
INSTALLATION CONSIDERATIONS The WS110R is a Decora-style module and is designed to use standard Decora-style cover plates and mounting hardware. Decora cover plates (up to 6-gang) with color-matched plate screws are available from your Niles dealer. TOOLS REQUIRED • 1/8” Standard Slotted Screwdriver • 1/4” Standard Slotted Screwdriver • Wire Stripper TYPE OF CABLE The WS110R connects to the Niles infrared main systems unit or IRH610 sensor expansion hub with an individual home run of CAT 5 cable.
INSTALLATION CONSIDERATIONS (CONTINUED) RECEIVING RANGE AND PICKUP ANGLE The receiving range of the WS110R will vary according to the IR output strength of the remote control being used. Remote strength varies among brands depending on the number and size of batteries used, and how many IR emitters the remote has. For example, remotes that operate on two small AAA batteries and have only one IR emitter are generally not as strong as remotes that use the larger AA size batteries and have two emitters.
INSTALLATION CONSIDERATIONS (CONTINUED) the WS110R. If you must locate the WS110R near electrical devices, install it in a separate metal electrical box, ground the box to the electrical system ground, and route the WS110R cable several feet away from all electrical wiring. AVOIDING INTERFERENCE The WS110R is designed to work in most applications including plasma and LCD displays and in areas where CFL lighting and indirect sunlight are present.
INSTALLATION CONSIDERATIONS (CONTINUED) Niles IR Flasher Stereo Receiver 12V DC power supply (supplied with the MSU250 Main System Unit) plugged into an unswitched AC outlet powers the system MSU250 12V DC Power Supply (Not Supplied) plugged into the Switched Outlet Niles Stock# FG01035 Power, IR Data, and Power Status Signal via category 5 cable Figure 1 Wiring Diagram (Typical installation with an MSU250 Main System Unit) WS110 IR Sensor 6
INSTALLATION CONSIDERATIONS (CONTINUED) Figure 2 WS110R Parts Guide a e b (a) Electrical Box (b) CAT 5 cable (c) WS110 IR Receiver (supplied) (d) Snap-on Color Insert (supplied) (e) Device Screws (2 supplied) (f) Decora Faceplate (supplied) (g) Faceplate Screws (2 supplied) NILES AUDIO CORPORATION – 1-800-BUY-HIFI g c f d e g 7
INSTALLATION CONSIDERATIONS (CONTINUED) CHANGING THE COLOR OF THE WS110R The Decora-style insert on the WS110R is removable, allowing fast and easy color changes as needed. Inserts are available in a variety of colors. If you need to change the color of the WS110R: 1. Obtain the WS110R Decora-style insert in the desired color from your Niles dealer. 2. Hold the WS110R as shown in Figure 3. Locate the two plastic mounting tabs at the top rear of the Decora-style insert.
INSTALLATION CONSIDERATIONS (CONTINUED) USING THE WS110R WITH THE INTELLIPAD CI SYSTEM. The WS110R is fully compatible with the Niles Intellipad Ci line, follow the wiring instructions in Figure 4. For specific information see your Intellipad Ci manual. Figure 4 This color code is based on the industry standard T568A coding for the RJ45 connector. When connecting the WS110R to the Niles Ci system observe this pin configuration.
INSTALLATION If you are installing the WS110R into an existing wall, take time to consider any possible obstructions which may be hidden inside the wall, such as wood or metal studs, electrical, telephone or other types of wiring, plumbing, AC or heating conduit, etc. 1. Locate the connector plug. 2. Strip 1/4” of insulation from the end of each wire. 3. Use a small flathead screwdriver or your thumbnail to raise the locking tabs, exposing the holes on the removable connector plug. 4.
IOPERATION Operation of the WS110R is simple. Stand within the operational range of your WS110R. Aim your hand-held remote at the WS110R and press the button for the desired command. Your IR command is instantly repeated to your A/V equipment. GREEN “POWER STATUS” LED When the WS110R is correctly connected (as shown in Figure 1), the Green LED will stay lit as long as the preamp/receiver is on. When your preamp/receiver is off, the LED will stay off.
TROUBLESHOOTING This manual contains instructions for the WS110R only. For specific information on the adjustment and operation of your Niles infrared extender system, please refer to the instruction manual included with your Niles IR main system unit (MSU140, MSU250, MSU480, MSU440Z). The bi-color blue/green LED on the front of the WS110R is a useful troubleshooting aid. The led should light solid green when status is detected. The blue LED should light only when a remote command is being received.
TROUBLESHOOTING (CONTINUED) ELIMINATING OPTICAL FEEDBACK In some installations, two conditions combine to create an optical feedback loop. Symptoms can include: poor range, intermittent operation or no operation. The conditions which sometimes combine to create a feedback loop are: 1. Both a sensor and a flasher are located within the same room. 2. There is some low-level noise or interference on your system.
TROUBLESHOOTING (CONTINUED) IR TEST LED OFF: Optical Interference IR TEST LED ON OR FLICKERING: Electromagnetic Interference EMI (ELECTROMAGNETIC INTERFERENCE) Identify the source of the interference. The most common sources of electromagnetic interference are listed in the Installation Considerations section on page 3. To eliminate EMI try the following methods: 1. Move the sensor or the sensor cable away from the EMI source or move the source of the EMI away from the sensor or the cable. 2.
SPECIFICATIONS IR System Compatible with virtually all brands of remotes using carrier frequencies of 38 kHz, 40 kHz and 56 kHz IR Receiving Range Varies depending on remote strength; Typically 20 to 35’ Unit Dimensions 1-5/8” wide x 2-5/8” high x 1-1/4” deep Face Plate Dimensions Decora wall plate; 2-3/4” wide x 4-1/2” high IR Receiving Angle 60° off-axis (horizontal and vertical) at 20’ Mounting In-wall, fits into most 18 cu. in.
LIMITED WARRANTY Niles Audio Corporation (“NILES”) warrants its active products (those requiring AC or battery power) to the original purchaser to be free of manufacturing defects in material and workmanship for a period of two years from date of purchase. This Warranty is subject to the following additional conditions and limitations.
Detach here and return to: Niles Audio Corporation Warranty Registration Dept. P.O. Box 160818 Miami, Florida 33116-0818 WARRANTY REGISTRATION CARD Model Purchased __________________________________ Serial Number __________________________ Date Purchased (month/day/year) ______________________ Dealer Name and Location _________________ ❍ Dr. ❍ Miss ❍ Mr. ❍ Mrs. ❍ Ms.
BLENDING HIGH FIDELITY AND ARCHITECTURE® Niles Audio Corporation 1 2 3 3 1 S . W. 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6 3 0 5 - 2 3 8 - 4 3 7 3 • 1 - 8 0 0 - B U Y- H I F I www.nilesaudio.com ©20 07 Nil es Audio Cor po r ati o n. A l l r i g hts r e se r ve d. Ni l es , the Ni l e s l o go s , In t e ll ip ad, M i cro f l as he rs an d Bl en din g Hi gh Fi del i ty and A r c h i te c tur e a r e r e gi s ter ed tr a de mar ks o f Ni l e s Audi o C orpo rat i on .
