INS oR Fran Par TY rae TABLE OF CONTENTS LOL UTE cL) [ECE ERT [LEECH Considerable Installation 8 Operation Ll Specifications 10 @ Baker AMPLIFIER SELECTOR Introduction The AB-2) is a wall-mount, Debora” style speaker selector. The unit has one amplifier input and two speaker pair outputs. With the AB-2, you can select an amplifier to play into either pair of loudspeakers both pairs simultaneously Features and Benefits The AB-20 offers a number of improvements over other AB selectors.
Ser OVERSIMPLIFICATION SELECTOR # 100% tested, electronically and acoustically, for frequency response, distortion and power handling. ® isolated deft and right channel grounds make it safe for use with any amplifier. ® May be used with ohm speaker systems. ® ideal for both home and commercial sound installations. @® Only screwdriver and wire stripper required for installation. # Power handling: 600 watts/channel continuous power WORMS. ® Frequency response: Flat from kHz.
Strikebreaker TOOLS REQUIRED ECR REL REAR ET Slotted Screwdriver RRL] EEE EE CRETE Hee Hero pt LEC a impedance EE EY Pa speaker pairs are EET fra EY refer [roe installation Considerations The AB-2 is a Debora-style module and is designed fo use standard Debora-style cover plates and mounting hardware, Debora cover plates (up to 6-gang) with color-matched plate screws are available from your Nile dealer.
OVERSIMPLIFICATION § the use of a p-ring may be inappropriate, such as in a retrofit (existing) installation, or when building codes require that wall devices be enclosed in electrical boxes. Contact your local bulling code and inspection department if unsure. Type of Speaker Wire For most applications, we recommend you use 16 or 18 gauge, stranded copper speaker wire for the AB-2 connections. For wiring runs longer than 80 feet, 14 gauge wire is recommended.
SPEAKER! AMPLIFIER SELECTOR ® Near other wall controls (see caution below) DO NOT INSTALL THE AB-2 INTO ELECTRICAL BOXES ‘WITH 110 VOLT DEVICES. Some states or municipalities allow devices such as the AB-2 to be installed into the same electrical box as 110 volt devices, provided a “low-voltage partition” is used between the devices. We do not recommend this, Speaker wires can act as an "antenna" for electrical noise.
SPEAKER SACRIFICIAL SELECTOR from you) until the insert paps free from its mounting slots. harlot 3. Hold the AB-2 as shown in {Figure 2). Remove bath buttons from the switches using your fingers, DO NOT use Do not exert pliers or other tools as these may damage the buttons. Locate the new Debora insert. Hold the AB-2 so that it mounting tabs. is facing you. Insert the two bottom tabs into the bottom slots first, followed by the two tabs on the top.
Oversimplification SELECTOR {8 Electrical Box © (0) Speaker Wire AB-20) Speaker Selector supplied) {d) Snap-on Color Insert (supplied) (6) Buttons (2 supplied) {6 Device Screws (2 supplied] {g) Debora Face plate (supplied) {h) Face plate Screws {2 supplied)
installation # you are installing the AB-2 into an existing wall, take time to consider any possible obstructions which may be hidden inside the wall, such as wood and metal studs; electrical, tel. phone or other types of wiring; plumbing; conduit; old wall safes; etc. 1. Install the electrical box or p-ring in the usual manner. 2. Run all the necessary wiring to the AB-2. Label the wires for future reference. 3. Make the connections to the AB-2.
Seg TAKERS Ea Figure 4 Loosening the Screws for a Flush Fit FILES SELECT 4. Secure the AB-2 to the electrical box or prong. Insert the 1 1/4" long device screws anti the oblong-shaped screw holes or the top and bottom of the AB-2. Note that the oblong shape of the screw holes allow you to position the AB-2 so that it Is vertical. Position the AB-2 so that the screws are aligned with the threaded holes in the electrical box or prong. Tighten the screws using a fillips screwdriver. DO NOT OVER-TIGHTEN.
Operation 1. Make sure the amplifier or receiver power is OFF and set the volume to minimum. 2. Set both selector buttons on the AB-2 to the OFF poi son (buttons out). 3. if you are using a Nile speaker selection system in conjunction with the AB-2, locate the ON/OFF button which corresponds to the AB-2, Set it to the ON position. 4. Turn on the amplifier or receiver and select a source, such as the tuner or CD player §. Using the selector buttons on the AB-20, select the speaker pairs you wish to play. 6.
[NES J [rear [rrr ree ER [EER ELE Fax: {305) 238-0185 wo corr pis ion A Sikh ei i ce Bee Sane te oor Pat te acre iid i : :
Can © JU pup Topsy dale seed {x on 2 4G000UM VSI Ui BOR ry Corruption SORRY SHIN 2002 & STUN & Place stamp here Nile Audio Corporation Customer Service Department PO. Box 160818 Miami, Florida 33116-0818 WARRANTY AND REGISTRATION CARD CONGRATULATIONS ON YOUR PURCHASE OF A LINES PRODUCT. WHEN PROPERLY INSTALLED AND OPERATED, YOUR NEW LINES PRODUCT WILL GIVE YOU YEARS OF TROUBLE FREE USE. A) LINES.
LIMITED WARRANTY Ties Auto Commemoration [HILLEL) w ants fis passive products those not equipping AC or battery power} ta the original paraphrase MANILA. truing footsie in serial and workman ship for a period of ten years from dale of purchase. Sites Auto Corporation [‘NILE'S) warrants #5 passive loudspeaker products firehouse not requiring AC or battery owes) 10 the original purchaser manufacturing defects in material and workmanship for & per or of fve Years fro hate of purchase.