NSB TESTY (RIE) PAGER E PC LEE Benefits [ATE EET [at] EET Considerations 5 [OEE ELE Testing the 1R Extender System Power Status Trouble Specifications 17 Addendum Li [pH ARES Mason System Ulnar Introduction An infrared (IR) extender system enables you to contra your IR remote controlled A/V equipment from a remote location. This enables you to place your A/V components out of sight {behind cabinet doors, in the rear of a room, or in a different room) and still conveniently operate your equipment.
INFRARED MAIN SYSTEM Features and Benefits The GYMSLIP offers a number of improvements over other IR Extender Main System Units: « Universal system—compatible with virtually all brands of AN equipment and remote controls, Accommodates four IR sensors or keypads. Provides eight flasher outputs via convenient 3.5mm jacks. System feedback LED confirms operation. 3-30 AC/DC status input. Provides system status to connected sensors and keypads.
INFRARED Main MSU430 Parts Guide LINES Wa. SEE id © [eo] wo 3 1. 12V DC Jack ~ Provides 12 coll DC power to MSU via a regulated power supply. 2. IR flasher outputs ~ 3.5mm jacks provide output for either single or dual (MF1, MF2, METE, MFUME} tow-level flashers. 3.3.30 AC/DC Status — 3.
CIMFRAREDIMAIN SYSTEM UNIT IMPORTANT Do not place the [ERIE Eee pr FICA prune Ea sets produce intense electromagnetic interference which EL IR extender system. Installation Considerations Placement of the M5U480 Place the MSU4B0 conveniently close to the equipment it will be controlling. Generally, the unit is placed in a concealed location because its controls and indicators are only used during installation.
Enter earn Mass System UNIT Wiring ar ” From every IR Sensor location you must “home-run” a hi re category S cable back to the MSU4B0. Home run means that an individual cable is connected between each IR Sensor and the MSU480 (Figure 4). Remotely Located JR sensors Figure 4: Home run the sensor cable from the sensor ic the HAMSUN.
INFRARED Main System Unit Figure 5 An IR sensor cable is “daisy-chained” from an Intel iPad, to 2 ‘sensor and back to the: MSL480. Intelligent Wiring When you are placing bath an Shinsplints and a sensor (or two keypads) in one room you may “daisy-chain” Using a single cable. A cable is run between the keypad and the sensor and a single cable is run from either the sensor back to the MSU480.
INFRARED Main System System Expansion System expansion is easily achieved (Figure 6) through the use of an IRHB10 Infrared Sensor Expansion Hub. Please see your authorized Nile dealer of refer to the AIRHEAD manual for details. Installation Before you begin, make sure that the somatosensory cables, the flasher cables and the 12VDC power supply cable will all reach the proposed location of the MSU480.
infrared Milan System Univ 1. Connect and test the power supply. If it tests OK, unpin the connector trim the power socket and proceed A) Plug the supplied 12VDC power supply into an switched 100-240V AC outlet . 8) Plug the connector into the socket marked “Power” on the MSU480, Cf the Power LED does not light, test the switched 100-240 AC outlet with another appliance. If the outlet tests OK, you have a defective power supply which must be replaced for you to continue. 2.
Infra Red Main SYSTEM Und EP 4. Plug the flashers into the Route the connecting wire to the IR Main System Unit, Connect flasher outputs. IF you need the 3.5mm fig into the jack labeled “Flasher Output” on the to extend the wire, use MSU4E0. a 2-conductor 16 gauge WARNING! or fr or Tech Tip Before connecting flashers to ports 7 & 8 set the HZ LOW switch. <5 to the appropriate position. Depending on the flashers being used: 1. MFT, MF2, MOTIVE, MF2VF LOW position. 2. RBI. Hi position.
INFRARED MAIN System Testing the IR Extender System Test your IR Extender system by following the three principal quinidine: 1. All components can be operated. Test all of your remote controls for all of your equipment. 2. Operation is consistent, A good test is to repeatedly step from Pause to Play with your VCR, CID, DVD, ot Tape player remote control. Operation should be identical to standing in front of the component with the remote control pointed directly at the sensor window. 3.
INFRARED Main System Univ 12 Volt Trigger Output The Nile M3U480 provides 2 12VDC output that can be trig. greed one of two ways: 1. The presence of status voltage on the 3-30V AC/DC status input jack. 2. Discrete infrared on and off commands. The discrete on and off commands are available for download at: This output can be used to rigger any device that requires 12V0DC to be activated. Examples include: * Dropping a motorized screen, * Activating a television lift.
Incinerated Mar System Contact Closure The Nile SWIMSUIT provides a contact closure that can be triggered one of two ways: 1. The presence of status voltage on the 3-30V AC/DC status input jack, 2. Disinterestedness on and off commands. Set the contact do sure dip switch, located above the screw less connector, to the appropriate position for triggering {Figure 8). The discrete on and off commands are available for download at wwwinilesaudio.
INFRARED Main System Univ Power Status — Installation Considerations Proper Power Supply You may connect a Nile 12vDC wall adapter (Nile FG00665) into the switched AC power outlet of the receivership in your system. Any 3-30¥ AC/DC power supply with a minimum of 20mA current capacity can be substituted. Extending the Cable If you must extend the cable from the wall adapter to the MSU480's status input jack be sure to maintain correct polarity.
infrared Main SYSTEM 2. Optical or Electromagnetic Interference Direct sunlight, reflections, neon signs and other sources of infrared fight or television sets, fight dimming controls and other sources of electromagnetic fields can induce noise and interference into your IR extender system. Symptoms can include: flashback LED's continuously flickering or on without any remote control use, poor range, intermittent operation of no operation. 3.
[N Feared Maw Specifications 1R System Compatible with virtually all brands of remotes using carrier frequencies between 26 and 105kHz. Wing Requirements Individual home-runs of category 5 cable from each somatosensory. Unit Dimensions 71/16" wide x high x 3 deep. Power Requirements TDC 1.25A regulated power supply Conclude.
INFRARED Mar System Unit Addendum: Using the MSU480 with the IntelliControl® automation system Using the MSU480 with the Controlling Home Theater automation system When connecting an MSU flasher output to an intercontinental “Home Theater” port, 2 150-Ohm resistor must be placed between the data and the ground fine of the intelligence IR sensor input (see figure above).
part ol ATTIC LATE) BALLROOM [24 fb [2A] FINE O IAL BATH RM 3 [i] fashionable BERM fC) 5a BEDROOM BOARD RM BONUS RM BREAKFAST [IRS [Krista y [ed DECK DEN PTE] ENTRY FAMILY FIVER [2 TE 4 GALLEY Re 30 [ers 20 3 peu [Vc OR UT SAUNA Lo ecru ER Ri GUEST RRM.