SCRUBTEC 770 S SCRUBTEC 770 L SCRUBTEC 784 S SCRUBTEC 784 L SCRUBTEC 795 S SCRUBTEC 795 L Operator's Manual U.S. Patent No. 6,760,947; No. 6,105,192; No. 6,493,896 (Deluxe Machines) READ THIS BOOK This book has important information for the use and safe operation of this machine.
Table of Contents Operator Safety Instructions ............................................................................................................................. 3 Introduction ....................................................................................................................................................... 4 Machine Specifications ....................................................................................................................................
OPERATOR SAFETY INSTRUCTIONS DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities. WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture. Keep the electrical components of the machine dry. Wipe the machine down after each use. For storage, keep the machine in a dry building.
Machine Specifications SPECIFICATIONS: Model Motor, Vac Scrubtec 795 S 1 HP (.74kw) three stage tangential discharge Power Supply 36 volt (6-6V batteries) 250AH, 330AH Solution Tank 30 gallon (114 liter) Recovery Tank 30 gallon (114 liter) Motors, Brush (2) 1 hp PM (.74kw) Motor Traction .50 hp PM (.37kw) Brushes (2) 19 inch (48cm) w/.5" (1.5cm) overlap Brush Speed 200 rpm Brush Pressure Variable 150 lbs. - 220 lbs. Speed, Forward Variable to 230 ft./min. Speed, Reverse Variable to 180 ft./min.
Machine Specifications SPECIFICATIONS: Model Motor, Vac Scrubtec 795 L 1 HP (.74kw) three stage tangential discharge Power Supply 36 volt (6-6V batteries) 250AH, 330AH Solution Tank 30 gallon (114 liter) Recovery Tank 30 gallon (114 liter) Motors, Brush (2) 1 hp PM (.74kw) Motor Traction .50 hp PM (.37kw) Brushes (2) 19 inch (48cm) w/.5" (1.5cm) overlap Brush Speed 200 rpm Brush Pressure Variable 140 lbs. - 220 lbs. Speed, Forward Variable to 230 ft./min. Speed, Reverse Variable to 180 ft./min.
PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: The machine is heavy. Make sure you use two able persons to assist the machine in climbing the ramp. 1. Make sure the loading ramp is at least 2.4m long, and strong enough to support the machine. 2. Make sure the ramp is clean and dry. 3. Put the ramp in position. 4. Remove squeegee assembly, brush housings, & brushes or pad drivers before loading. 5. Turn key switch "ON". 6. Align the machine on a level surface 3.
SYMBOLS USED ON SCRUBTEC 770, 784, 795 SYMBOLS USED ON SCRUBTEC 770 S, 784 S & 795 S SCRUBTEC 770 L, 784 L, 795 L Hazard Alert Symbol On/Off Key Switch SYMBOLS USED ON SCRUBTEC 770 S, 784 S & 795 S Power SYMBOLS USED ON SCRUBTEC 770 L, 784 L & 795 L Squeegee Up/Down Additional Brush Pressure Traverse Speed Control Solution Control Brush Up/Down Hour Meter Switch Brush Up/Down Charge/Battery Meter Page -8- Solution Control Charge Indicator CLARKE TECHNOLOGY One Touch Switch Operator's Manual
SYMBOLS USED ON SCRUBTEC 770, 784, 795 WARNING WARNING READ OPERATOR'S MANUAL BEFORE OPERATING THIS MACHINE READ OPERATOR'S MANUAL BEFORE OPERATING THIS MACHINE EXPLOSIVE GASES, CAN CAUSE SEVERE INJURY, DEATH OR DAMAGE TRANSFORMER. • Keep flammable materials away from batteries. Charge in a cool well ventilated area. RISK OF FIRE • Use only commercially available floor cleaners and waxes intended for machine operation. • Do not use flammable materials. 71018A BATTERIES CONTAIN SULFURIC ACID.
MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S Key Switch (See Figure #1, Item "A") The key switch turns "ON" the power to the control panel. "0" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #1, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left.
MACHINE CONTROL PANEL SRUBTEC 770 S, 784 S & 795 S B G F F E C D A M L K J I H N Figure #1 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 - 11 -
MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Key Switch (See Figure #2 Item "A") The key switch turns "ON" the power to the control panel. "O" is "OFF" and "I" is "ON". Traverse Speed Switch (See Figure #2, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left.
MACHINE CONTROL PANEL SRUBTEC 770 L, 784 L & 795 L Circuit Breakers (See Figure #2, Item "K", "L", "M") The circuit breaker reset buttons are located on the control panel. The breakers are located as follows: "M" - Brush Motors (35A); Item N - Key Switch (5A). Item "L" and If a circuit breaker trips, determine which motor is not operating and turn the key switch "OFF". Wait five minutes and push the reset button back in. Turn the key switch "ON", and try again.
Display Screens For SCRUBTEC 770 L, 784 L, 795 L Position arrow indicating current position of squeegee (up or down) 3 Indicators are on all the time showing current settings. SCREEN 1 Water “droplets” off when solution is off and they are flashing when solution is on. Screens Available to Operator “Battery” blinks when low voltage occurs. Arrows indicating vacuum status. They are flashing when vac is on and off when vac is off. SCREEN 2 Example SCREEN 3 (Diagnostic) The Diagnostic only.
EN MACHINE CONTROLS & FEATURES Squeegee Lift Handle ("S Class" models only) See Figure #3a, 3b, & 3c. The squeegee lift handle is located below the control handles on the right side. It is used to raise or lower the squeegee. The vac motor is turned on when the handle is lowered. Parking Brake (Optional)See Figure #4. The parking brake prevents movement of the machine. The brake is located on the left hand side of the transaxle motor.
HOW TO PREPARE THE MACHINE FOR OPERATION To Install the batteries, follow this procedure: 38720B The Scrubtec machines use six 6-volt batteries. The batteries are located in the battery compartment under the recovery tank. 38720B 38722B How To Install The Batteries 1. Turn key switch off. 38722B 2. Make sure both tanks are empty. 3. Disconnect the hoses from the recovery tank (upper tank) & unplug the vac motor and float switch. 38720B 38722B 4. Remove the tank support bracket. Figure #6a 5.
HOW TO PREPARE THE MACHINE FOR OPERATION Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventive maintenance. WARNING: Correct fill level Working with batteries can be dangerous. Always wear eye protection and protective clothing when working near batteries. NO SMOKING! To maintain the batteries in good condition, follow these instructions: Figure #7 1. Keep the electrolyte at the correct level. The correct level is between 6.
HOW TO PREPARE THE MACHINE FOR OPERATION How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. Keep sparks and flames away from batteries. NO SMOKING! To charge the batteries, follow this procedure: 1. Make sure the key switch is in the “OFF” position. 2.
HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers To install the brushes or pad drivers on the machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the front of the machine. 5. Unlatch right and left brush housings and remove them. See figure #9. Figure #9 6. Put a brush or pad driver under the brush motor plate. See figure #10. 7.
HOW TO OPERATE THE MACHINE How to Operate the One Touch System ("L Class" models only) One touch cleaning is a feature on the new Scrubtec Walk-behind Scrubber. The factory defaults for this setting are two bars of brush pressure and four bars for solution flow and squeegee in the down position. 1. Press and release the green button for all cleaning functions to begin, see figure #11, item A. 2. The squeegee and brush head lower to the floor and the vacuum starts.
HOW TO OPERATE THE MACHINE How To Operate the Squeegee ("S Class" models only) The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. Use your right hand to lower or raise the squeegee handle. To operate the squeegee, follow this procedure: 1. To lower the squeegee and start the vac motor move the squeegee lever to the right and down. See figure #12. 2. To raise the squeegee, lift the squeegee lever up. See figure #13.
HOW TO OPERATE THE MACHINE How To Traverse Machine NOTE: Put the machine in the slow traverse speed (see figure #17). Use the machine in an area that has no furniture and objects until you can do the following: 1. Move the machine in a straight direction, forward and backward. 2. Stop the machine safely. 3. Move the machine in a straight direction after you turn the machine. To move the machine, follow this procedure: 1. Turn the key switch “ON” position. 2. Put the brush switch in the "UP" position.
HOW TO OPERATE THE MACHINE How to Clean a Very Dirty Floor To clean a very dirty floor, follow this procedure: 1. Apply solution to the floor. 2. Do not lower the squeegee. 3. Do not activate the vacuum motor. 4. Lower the brushes and scrub the floor. 5. Leave the solution on the floor long enough for the solution to begin cleaning the floor. 6.
MAINTENANCE Do These Procedures When You End Your Work 1. Drain the solution tank (Figure #21, item A) and the recovery tank (Figure #21, item B). To drain the tanks , follow this procedure: a. Turn the key switch “OFF”. b. Remove the drain hose from the back of the machine. B A c. Put the end of the hose over a drain or bucket. d. Recovery Tank: Turn the valve housing to the left (see figure #22). To open the valve completely, turn the housing fully to the left and pull the housing off of the valve.
MAINTENANCE These Maintenance Procedures Must Be Done Every Week: WARNING: Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and the recovery tank before doing any maintenance. Keep all fasteners tight. WARNING: Always wear eye protection and protective clothing when working near batteries. Do not put tools or other metal objects across the battery terminals or the tops of the batteries.
MAINTENANCE 7. Check the squeegee and the scrub brushes or the pad drivers for damage. 8. Check the squeegee and the vacuum hose for dam age, leaks and obstructions. Maintenance For The Squeegee To remove the squeegee, follow this procedure: 1. Remove the squeegee assembly by loosening the two knobs that attach the squeegee to the machine. Pull the squeegee assembly off. See figure #26. Figure #26 2. Inspect the squeegee blade. 3.
MAINTENANCE Adjusting Squeegee Blades When properly installed the front blade should be approximately .06 above the rear blade. See figure #29. Adjusting Squeegee Support Wheels: The support wheels should be set at .12 above the floor with the rear blade touching the floor. See figure #31. WARNING: Maintenance and repairs must be done by authorized personnel only . WARNING: Electrical repairs must be done by authorized personnel only. .
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM The machine does not remove all the water from the floor. The batteries do not give the normal running time. The cleaning is not even. CAUSE ACTION The squeegee is up Lower the squeegee. The vacuum tank is full. Drain the tank. The screen filter is dirty. Clean the screen filter. There is an obstruction or damage in the squeegee, squeegee hose or standpipe. Remove the obstruction or repair the damage. The vacuum motor is not running.
SCRUBTEC 770 L, 784 L, 795 L Common Error Codes ERROR CODE CAUSE ACTION 3100 3101 3102 3103 3104 3105 Probable short circuit of output device. Check the traction, brush and vac motor connections on the trio and check wiring from these connectors down to the traction, brush and vac motors. 7600 Open circuit on brush motors or brush motor wiring. Check the brush motor connection on the trio and check the wiring from this connector down to the brush motor.
SCRUBTEC 770 / 784 / 795 Accessories - 2/05 ACCESSORIES Description Part No. Power Wand System Kit 10892A ESP Recycle System Kit 10894A Soft Caster Asm. 52127A Care Kit 14607A Squeegee Asm.
SCRUBTEC 770 S SCRUBTEC 770 L SCRUBTEC 784 S SCRUBTEC 784 L SCRUBTEC 795 S SCRUBTEC 795 L Section II Parts and Service Manual (70935A) U.S. Patent No. 6,760,947; No. 6,105,192; No.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Solution Tank Assembly Drawing 9/05 1 2 3 46 35 47 33 34 4 36 37 6 40 38 39 10 42 43 7 8 9 41 30 To Electrical Panel 5 44 11 12 31 32 31 12 30 29 13 22 28 21 23 24 -32- 16 17 18 15 45 Page 19 21 27 26 14 20 25 21 CLARKE TECHNOLOGY 24 Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Solution Tank Assembly Parts List 9/05 Ref # 1 2 2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 46 47 Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Recovery Tank Assembly Drawing 2/05 1 2 5 3 7 6 8 3 4 9 37 38 39 10 11 12 36 15 23 35 13 22 16 17 9 26 18 14 34 27 33 24 28 20 20 32 20 21 11 29 19 25 30 31 Page -34- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Recovery Tank Assembly Parts List 9/05 Ref # Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S Electrical Panel Assembly Drawing 9/05 Drawing # 10849E 41 39 40 38 36 10 47 34 26 28 27 16 5 15 44 37 2 50 1 5 13 14 12 30 7 11 17 31 5 45 5 6 18 5 35 9 20 32 46 49 18 29 10 48 33 21 43 42 25 24 20 19 6 3 23 22 5 8 7 4 Page -36- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S Electrical Panel Assembly Parts List 9/05 Drawing # 10849E Ref # Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Electrical Panel Assembly Drawing 9/05 Drawing # 10855E 29 30 18 10 5 21 20 35 31 32 5 13 31 33 12 2 1 5 18 16 9 15 17 27 14 7 11 6 5 2 34 5 5 26 19 20 6 25 3 24 22 5 23 28 8 7 Page -38- CLARKE TECHNOLOGY 4 Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Electrical Panel Assembly Parts List 9/05 Drawing # 10855E Ref # Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Control Panel Assembly Drawing 9/05 7 7 10 12 6 9 14 8 4 13 3 14 11 15 16 1 2 3 20 23 22 17 19 21 18 24 30 32 25 28 29 31 31 32 26 30 27 30 36 9 35 34 33 17 18 24 32 37 31 28 29 40 39 26 30 38 43 30 42 44 41 Page -40- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Control Panel Assembly Parts List 9/05 Ref. # Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Squeegee Swing Arm Assembly Drawing 2/05 55 53 2 1 7 2 53 3 6 50 8 53 57 4 9 10 16 6 15 23 16 53 11 25 12 13 24 26 52 51 17 14 58 5 18 6 19 20 22 27 21 10 29 6 28 31 32 48 30 33 56 37 NOTE: #51 and #52 are on top of the bracket for the "S" models 32 28 34 47 41 42 35 43 40 38 39* 37 36 54 44 45 46 49 Page -42- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Squeegee Swing Arm Assembly Parts List 2/05 Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Part No. 57275A 87623A 60452A 86004A 85730A 81104A 38021A 61679A 51613A 920110 60332A 920256 81105A 920296 962798 87624A 80015A 53423A 68016A 170915 64905A 980651 60678C 25201A 35192A 61267A 34260B 81301A 59971A 65975A 920248 980645 59950A 980638 Description Pulley Washer, Nylon 1¼x¼x1/8 Swing Arm, Front Screw, .
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Traverse System Assembly Drawing 2/05 18 24 25 26 27 16 8 23 10 9 7 6 5 15 7 23 4 19 28 19 14 20 3 3 29 2 30 1 11 21 30 32 13 31 13 12 Page -44- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Traverse System Assembly Parts List 2/05 Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 66531A 836711 81104A 69877A 85811A 57275A 87623A 86004A 962288 85700A 920110 899769 81105A 59116E 15 16 85730A 59969A 59955A 81221A 980614 61594A 65963A 87625A 80011A 81207A 170883 58419A 980205 69639A 980645 962244 980638 32417B 18 19 20 21 23 24 25 26 27 28 29 30 31 32 NI Description Swing Arm Pin Hair Pin Nut, .25-20 ESNA Swing Bracket Screw, .312-18 x .
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Brush Head Assembly Drawing 2/05 1 2 3 4 5 55 6 8 1 9 7 2 10 11 54 12 49 50 51 49 47 48 13 53 20 14 15 16 17 46 18 19 13 45 52 44 43 27 42 40 39 41 38 37 20 21 30 22 29 28 23 36 31 27 26 25 24 32 35 17 34 Page -46- CLARKE TECHNOLOGY 33 Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Brush Head Assembly Parts List 2/05 Ref # 1 2 3 4 5* 6 7 8 9 10 11 12*** 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Part No.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Brush Motor #45036A 2/05 13 7 12 12 1 13 2 Seam Location 3 14 16 Rotation 4 5 15 6 17 8 9 10 11 Ref # Page -48- Part No. Description 1 2 3 4 5 46734A 40318A 902654 902550 51840A 6 7 8 9 10 11 12 13 14 15 16 17 50520A 56480A 962546 50517A 448396 40826A 55657A 55656A 59805A 50515A 80501A 54238A Qty Stator Assembly (w/Magnets & Clips) Armature Asm.(w/B.E. & F.E. bearings) Bearings B.E. Bearing F.E.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Gear Box #54238A 2/05 9 8 7 6 5 4 3 2 1 Ref # 1 2 3 4 5 6 7 8 9 NI Part No. 57846A 507641 52050A 56668A 51176A 58316A 902605 54883A 58144A Description Ring, Snap Seal, Oil, Small Cap End O'Ring Bearing, Large Shaft & Gear, Gearbox Bearing, Small Housing Seal, Oil Large Darina Grease CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 Qty 1 1 1 1 1 1 1 1 1 4oz.
CLARKE TECHNOLOGY SCRUBTEC 770 / 784 / 795 Vac Motor Assembly #45019A 2/05 13 18 2 1 14 4 3 6 15 5 16 7 8 14 9 15 19 14 10 11 17 12 Ref # 1 2 3 4 5 6 7 8 9 10 Page Part No. 51913A 54809A 53905A 85303A 40830A 51914A 50618A 53100A 902679 902648 -50- Description Clip (optional) Housing Fan Screw - 8-32 x 3/8 Carbon Brushes Clamp Bracket Disc Bearing - Ball Bearing - ball, radial Qty 2 1 1 4 2 2 1 1 1 1 Ref # 11 12 13 14 15 16 17 18 19 CLARKE TECHNOLOGY Part No.
Part No. 53384A 53385A 80121A 80122A 3 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 2 4 17 5 6 Parking Brake Spare Parts Description Pad, Friction Hub, Shaft Key, 4 MM - Hub Set Screw, M3 - Hub 1 7 8 To replace coupler remove these two screws (Black) to separate the motor from gearbox to allow access to coupler 9 Qty 1 1 1 1 10 4 16:1 Ratio 36 VDC 15 Cont Volt AMP. Duty Date 11 Ser. No. Mount Shaft 4BC-2800 1200 Ins. Cl. Model RPM .
CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S Control Panel Connection Diagram 2/05 CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S (Front of Machine) Connection Diagram 2/05 Page -52- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Control Panel Connection Diagram CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L (Front of Machine) Connection Diagram 2/05 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 - 53 -
CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S Electrical Plate Connection Diagram 9/05 Page -54- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Electrical Plate Connection Diagram 9/05 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 - 55 -
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Control Housing Connection Diagram 2/05 Page -56- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 S / 784 S / 795 S Electrical Schematic 9/05 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 - 57 -
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Electrical Schematic (pages 58 - 59) 9/05 Page -58- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795
CLARKE TECHNOLOGY SCRUBTEC 770 L / 784 L / 795 L Electrical Schematic (pages 58 - 59) 9/05 CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 - 59 -
CORPO HEADQUARTERS DENMARK Nilfisk-Advance Group Sognevej 25 2605 Brøndby Denmark Tel: (+45) 43 23 81 00 SUBSIDIARIES AUSTRALIA ALTO 48 Egerton St. PO Box 6046 Silverwater NSW 2128 Australia Tel: (+61) 2 8748 5966 Fax: (+61) 2 8748 5960 AUSTRIA ALTO Österreich GmbH Nilfisk Advance AG Metzgerstrasse 68 5101 Bergheim/Salzburg Austria Tel: (+43) 662 456 400 11 Fax: (+43) 662 456 400 34 E-mail: verkauf@-alto.at www.-alto.at BRASIL Wap do Brasil Ltda. Rua das Palmeiras, 350-Bairro Capela Velha 83.
GREAT BRITAIN ALTO Division of Nilfisk-Advance Ltd. Bowerbank Way Gilwilly Industrial Estate Penrith Cumbria CA 11 9BQ Great Britain Tel: (+44) 1 768 86 89 95 Fax: (+44) 1 768 86 47 13 E-mail: sales@-alto.co.uk www.-alto.co.uk HUNGARY ALTO Hungary Kft Csengery ut.
CLARKE TECHNOLOGY LIMITED U.S. WARRANTY This Clarke Technology Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service, when operated and maintained in accordance with Clarke Technology's Maintenance and Operations instructions. The warranty period is subject to the conditions stated below.