Instruction Manual

Lantern Wireless Charger
Speaker Instruction Manual
SL332
1 x Speaker
1 x USB to Micro-USB Charging Cable
1 x Instruction Manual
Model: SL332
Item No.: BC20789
Input: DC 5V/2A
Wireless output: DC 5V/1A
Battery capacity: 3.7V/3600 mAh
Speaker output power: 3W
⑨
(Be sure to fully charged the speaker before
Charging the Speaker
Connect the provided charging cable to a
power source and micro USB port on the
speaker (1).The LED indicator will flash red
when charging and turned into solid when
fully charged.
Wireless Charging:
• Short or long press the Play/Pause/ON/OFF
button (5), wireless Charging LED (8) will flash
red two times.
Front
Back
Pairing Setup:
Long press the Play/Pause/ON/OFF button (5),
the Bluetooth LED Indicator (8) will flash blue.
Turn on the Bluetooth function on mobile
device, select “BC20789” pairing name, the
Playing Music:
Short press “Play/Pause” key to pause or Play
music.
“Vol+/Next track”:
Short press - next track.
Long press - increase volume.
“Vol-/Previous track”:
Short press - previous track
Long press - reduce volume
1.
•
2.
3.
•
•
•
•
4.
•
Lantern:
Short press Lantern ON/OFF button sequentially
to enable the “High lightness” “Low lightness”
“Flash” “Lantern off”.
Long press Lantern ON/OFF button to turn on
the SOS function.
5.
•
•
1. Micro-USB charging port
2. Charging LED Indicator
3. Vol-/Previous Track
4. Lantern ON/OFF button
5. Play/Pause/ON/OFF
6. Vol +/Next Track
7. Wireless charging area
8. Bluetooth/Wireless charging LED Indicator
9. Lantern
What’s included:
Functions:
Instructions:
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F(0°C) or above
113°F(45°C).
Do not overcharge Phone. Unit may get
hot with excessive use. Remove Phone
when it is fully charged. Never charge for
more than 7 hours at a time.
The unit’s full performance is achieved
only after 2 or 3 completed charge and
discharge cycles.
To reduce the risk of injury, close
supervision is necessary when the product
is used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. For
professional. Incorrect reassembly may
or temperatures above 113°F may cause
explosion.
use only identical replacement parts to
ensure product safety
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
SAFETY PRECAUTIONS:
FCC Statement:
MADE IN CHINA
This device complies with Part 18 of the
FCC Rules.
The interference potential of the device or
system.
Maintenance of the system.
Simple measures that can be taken by the
user to correct interference.
For RF lighting devices, provide an advisory
statement, either on the product packaging
or with other user documentation, similar to
the following:
This product may cause interference to radio
•
•
•
•
•
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful
interference, and
(2)This device must accept any interference
received, including interference that may
cause undesired operation.
Warning:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate the equipment.
FCC ID : 2ABHA0077
• Place wireless charging supported mobile
device on top charging area, the Phone will
begin to be charged automatically. The LED
will glow red when device is charging.
LED will flash blue slowly if it is successfully
paired.
Speaker will automatically pair if the mobile
device has been paired before.
Long press the Play/Pause/ON/OFF button (5)
again to turn off the speaker.
equipment and should not be installed near
maritime safety communications equipment
or other critical navigation or communication
equipment operating between 0.45-30 MHz.