Specifications

+
-
+
-
BLUETOOTH
CEILING
SPEAKER
FLF-6BT/FLF-6BTS
CONNECTION
1.
3. Click “BT Speaker” to pair with your device.
Open the setting menu and select Bluetooth.
2. Turn on Bluetooth and search devices.
Ensure the speaker is connected to the power supply and turned on. Once the speaker
has powered up for 10 seconds, the power indicator flashes blue indicating that the
speaker is ready to pair. Any Bluetooth device (such as phones, tablets, laptops etc.) is
available for pairing. Once paired successfully, the power indicator will become steady blue.
SPECIFICATIONS
4 5
FLF-6BT Bluetooth Ceiling Speaker (Active)
Ø233x105mm(Ø9.2"x4.1")
6.5" Polypropylene Cone
0.75" Silk Dome
70Hz-20kHz
87dB
8Ω
2x30W/8Ω
V5.0
Active Speaker(Master)
10m (32.8 ft.)
DC 24V/2.5A
60W
6.5" Polypropylene Cone
Passive Speaker(Slave)
/
0.75" Silk Dome
70Hz-20kHz
87dB
8Ω
/
/
Dimensions
/
/
Woofer
Tweeter
Bluetooth Version
Bluetooth Distance
Amplifier Power
Nominal Impedance
Frequency Response
Sensitivity(1M/1W)
Power Supply
RMS Power
Speaker
FLF-6BTS Bluetooth Ceiling Speakers Pair (Active+Passive)
Ø233x105mm(Ø9.2"x4.1")
Cutout Size
Ø209mm (Ø 8.2")Ø209mm (Ø 8.2")
1) Bluetooth Pairing
Note:
2) Connect to a CD/DVD Player
1.
(Bluetooth Input has the priority when Bluetooth input and RCA input are
connected simultaneously.)
3. The RCA mode will be activated when the indicator light shows solid purple.
Connect to the speaker using a dual RCA left/right cable.
2. Switch the Bluetooth OFF on your device and wait for around 10 seconds.
Note: You need to wait around 30 seconds to activate the RCA mode if you have
restarted the speaker while no Bluetooth device is pairing.
3) Create Stereo Pair
1.
2. Slide the mono-stereo switch to the stereo position.
Connect the passive speaker to the phoenix connector output.
8
4) Remote Control
VOLME
TREBLE
BASS
RESET
PREV
PLAY/PAUSE
NEXT
BALANCE
+
ON OFF
POWER
+ +
---
a
b
c
d
e
f
g
h
I
j
a
Power On/Off
Press to turn on/off the speaker.
b
Mute
Press to turn off the sound
temporary, and press again to turn
the sound back.
c
Volume+/-
Press to increase or decrease the
sound level. You will hear a beep
when the volume reaches the highest
or lowest level.
e
Bass +/-
Press to increase or decrease the low frequency response. You will hear
a beep when the bass reaches the maximum or minimum value.
Tips:
The infrared remote control has effective scope of operating range which is less than 3m(10 ft.)
and at 60 degrees angle left or right away from the system.
The remote control is powered by a CR2025 lithium coin cell battery (included).
f
Balance L/R
Shift the balance of stereo output left and right. Note that turning the
balance control all the way in either direction causes output from the
other side to be eliminated entirely.
g
Reset
Short press repeatedly to select the sound effect: (1) Classical,
(2)Vocal Enhance, (3)Flat, (4)Bass Enhance, (5)Bass Weaken,
(6)Treble Enhance, (7)Treble Weaken, (8)Popular, (9)Rock, (10)Jazz.
Long press to resume the speaker to default setting. All parameters will
be reset to default values: volume is 26; sound effect is flat; treble and
bass is 0;L/R channel setting is balance.
d
Treble +/-
Press to increase or decrease the high
frequency response. You will hear a
beep when the treble reaches the
maximum or minimum value.
h
Previous
Short press for previous track.
I
Next
Short press for next track.
j
Play/Pause
Note:
CARE AND MAINTENANCE
Turn off the power to the speaker when unused for long periods of time.
Ensure all equipment is turned off prior to cleaning. Surfaces need only
occasional dusting/cleaning. Never use chemicals or solvents as they may
damage the surface. Always clean using a dry cloth.
Never touch the speaker drivers.
Only if the Bluetooth input is activated, the PREV, NEXT and RESET keys can work.
The customized volume and sound effect setting cannot be saved when the speaker is unplugged
from the mains directly without powering it off by the remote control first.
One device can only connect or control one Bluetooth speaker at a time.
If your device prompts a pairing code, type in the PIN “0000”.
If pairing fails the first time, restart all the equipment and then follow the above
instructions. If trouble persists, press the “reset button” located on the front of the
speaker or on the remote control.
If you are unable to reconnect a previously connected device, remove the “BT Speaker”
form the list of paired devices, and then follow the above instructions again.
The Bluetooth connection will be lost if the distance between the speaker and the
Bluetooth device exceeds 10m(32.8 ft.).