User's Manual

califone.com
6
califone.com
7
4. SETUP AND INSTALLATION
4.1 USAGE AND POWER (WS-T & WS-R)
1. The WS-T and WS-R beltpacks may be worn on the belt for
personal use (battery operation) or may be plugged into a WS-
CR cradle for use on a tabletop or mounting to a wall.
2. Before use, for best performance be sure to recharge the
beltpacks using either the WS-CH 4x Charger or WS-CR cradle.
4.2 RECHARGING BELTPACKS WITH THE WS-CH
1. Connect the power adapter (WS-CHP) to the wall outlet and then
to the DC IN jack on the back of the WS-CH 4x Charger.
2. Connect up to 4 WS-T or WS-R beltpacks to the charging
leads on the WS-CH unit. The beltpacks will immediately begin
charging. A red LED on the WS-CH indicates the unit is charging.
A green LED indicates that charging is complete.
3. For charging more than 4 beltpacks simultaneously, up to 3 WS-
CH chargers may be daisy-chained to recharge 12 beltpacks
simultaneously.
NOTE: The beltpack may be operated while recharging.
4.3 RECHARGING A BELTPACK WITH THE WS-CR
1. Connect the power adapter (included with the WS-CR) to the
wall outlet and then to the DC IN jack on the back of the WS-CR
charging cradle.
2. Insert the WS-T or WS-R beltpack into the WS-CR unit until it
clicks into place. The unit will immediately begin charging. A red
LED on the WS-CR indicates the unit is charging. A green LED
indicates that charging is complete; however, the LED will only
turn green if the beltpack power is turned off.
NOTES:
• The beltpack may be operated while recharging.
• The cradle can be hung on the wall using standard screws.
4.4 POWER ON AND OFF (WS-T & WS-R)
1. To turn on the beltpack power, hold the power button for 2-3
seconds. The LCD will light up with the current settings. The
power LED on the top of the beltpack will light green.
2. To turn off the beltpack power, hold the power button for 2-3
seconds.
NOTE: When the battery is running low, the power LED will turn red.
4.5 MANUAL CHANNEL SELECTION (WS-T & WS-R)
1. First, turn on the power of the WS-T or WS-R beltpack using the
power on procedure in section 4.4.
2. For the WS-T transmitter, ensure that the channel you want to
use is not already in use and that the frequency is clear of any
interference.
3. Change the channel on the beltpack. To do this, rst ensure that
the CHANNEL LOCK switch on the back of the unit is switched
to OFF
.Then press the CHANNEL UP or CHANNEL DOWN
buttons to change the channel. To move quickly through the
channel list, hold the CHANNEL UP or CHANNEL DOWN button.
4. Once the desired channel is selected, it’s suggested to put the
CHANNEL LOCK switch in the ON
position so that the channel
is not changed accidentally.
WS-C R
CHARGING CRADLE
CHARGING
1
4
3
2
6
5
1. TX Power Indicator
2. Channel Number
3. Channel Frequency
4. Channel Lock Indicator
5. Walkie-Talkie Mode Indicator
6. Battery Level Indicator
7. Volume Level Indicator
WS-T LCD Screen Layout
1
4
3
2
7
6
1. RX Power Indicator
2. Channel Number
3. Channel Frequency
4. Channel Lock Indicator
5. Sensitivity Mode Indicator
6. 85dB Limiter Indicator
7. Battery Level Indicator
8. Volume Level Indicator
WS-R LCD Screen Layout
7
8
5
WS-CR Charging Cradle WS-CR Power Adapter
WS-series Manual - JH 2010.01.13.indd 8-9 3/1/2010 11:23:51 AM