WIRELESS THERMOMETER Instruction manual 1.Description of parts Fig.
Fig.
Fig. 3: Transmitter C1 Fig. 3 C1: Wall mounting hole C2: LED index C3: Battery compartment C4: Switch 1-2-3 for channel selection C5: TX button C2 C4 C5 C3 2. Before you start using it • Please make sure to read the instruction manual carefully. This information will help you to familiarise yourself with your new device, to learn all of its functions and parts, to find out important details about its first use and how to operate it and to get advice in the event of a malfunction.
• We shall not be liable for any damage occurring as a result of non following of these instructions. Likewise,we take no responsibility for any incorrect readings and for any consequences which may result from them. • Please take particular note of the safety advice! • Please keep this instruction manual for future reference. 3.Scope of delivery • • • • Wireless weather station (Receiver) Micro USB wire Outdoor transmitter (CH1) Instruction manual 4.
• Time date display. • Alarm function. 5. For your safety • This product is exclusively intended for the field of application described above. It should only be used as described within these instructions. • Unauthorized repairs, modifications or changes to the product are prohibited. ! Caution! Risk of injury: • Keep these instruments and the batteries out of the reach of children. • Batteries must not be thrown into a fire, short-circuited, taken apart or recharged.
. Getting started 6.1 Inserting the batteries in the receiver • Place both instruments on a desk with a distance of approximately 1.5 meter. Avoid getting close to possible interference sources (Electronic devices and radio installations). • Remove the protective foil from the display of the receiver. • Connect the basic station to the attached micro-usb wire,and put USB port into 5V/1A power part,like computer,the charger of phone,etc. (This way the backlight will be light all time.
6.2.1 Reception of the outdoor values • The outdoor values of the outdoor transmitter will be transmitted to the receiver. The displays of the outdoor values are flashing "--.-". • On the display of the receiver appear the channel number. • If receiver receive the signal, it will display the current temperature of transmitter in OUT position. • If the reception of the outdoor values fails within three minutes, "- -"appears on the display. Check the batteries of the transmitter and try it again.
• The RCC reception always takes place hourly between 2:00 and 5:00 o'clock in the morning. If the reception is not successfully received until 5:00 o'clock, the next receive operation is again at 2:00 o'clock in the morning.
Please take note of the following: • The recommended distance to any interfering sources like computer monitors or TV sets at least 1.5-2 meters. • Inside ferro-concrete rooms (basements,superstructures),the received signal is naturally weakened. In extreme cases, please place the unit close to a window to improve the reception. • During night-time, the atmospheric interference is usually less severe and reception is possible in most cases.
7.1.2 Setting of the 12 and 24 hours display • In the setting mode you can choose between the 12 - and 24 hour system. • In the 12 HR system AM or PM (after 12 o'clock) appears on the display. 7.2 Setting of the alarm time .• Press the ALSET SET button into ALARM mode, “ALARM” words displayed. • Hold the ALSET SET button for 3 seconds to set alarm time. • The setting sequence is shown as follows: Hour - Minute. • Press the or button to increase or decrease for setting.
9. Thermometer and hygrometer • If the measure values above the range,then temperature display "HH.H",humidity display "HH%". • If the measure values below the range,then temperature display "LL.L",humidity display "LL%". 9.1 Maximum/Minimum function • Press the MEM button in normal mode. • MAX appears on the display. • You can now get the highest values for the indoor temperature and humidity and outdoor temperature since the last reset. • Press the MEM button again. • MIN appears on the display.
10. Additional outdoor transmitters • For having more than one additional outdoor transmitter select with the 1/2/3 switch in the battery compartment of the outdoor transmitter for each single outdoor transmitter a different channel. The reception of the new transmitter will be transmitted automatically to the receiver. Press and hold the button on the receiver or restart the receiver according to the manual. • The outdoor values will be shown on the display of the receiver.
11. Positioning and fixing of receiver and the outdoor transmitter • With the foldable leg at the back of the receiver, the receiver can be placed onto any flat surface or wall mounted at the respective location by the hanging holes at the back of the unit. Avoid the vicinity of any interfering field like computer monitors or TV sets and solid metal objects. • With the hanging hole at the back of the outdoor transmitter, the transmitter can be wall mounted at the respective location.
13.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.